UMAX Technologies Astra 1200S Bedienungsanleitung

UMAX Astra 1200S

Scanner Operation Manual

This operation manual contains all the information you need to install your scanner. For quick

installation instructions, see the Quick Start Guide accompanying your scanner.

!Make Sure the power is OFF before installing.

Important Safeguards

• Read all of instructions.

• Save these instructions for later use.

• Follow all warning and instructions marked on the product.

• When replacement parts are required, be sure that service technician has used

replacement parts specified by the manufacturer that have the same result in fire, electric

shock, or other hazards.

• Do not use this product near water or in rainy/moist situation.

• Do not place on an unstable table to avoid the series of damage to the product.

• The product should be operated only from the type of power source indicated on the

marketing label.

• Do not attempt o service this product yourself as opening or removing the enclosure may

expose you to dangerous voltage or other hazards.

• This unit has an autoranging input circuitry suitable for 120Vac and 240Vac.

• The sound pressure level at the operators position according to IEC 7041:1982 is equal or

less than 70dB(A).

• The following adapters are approved to be used with TUV-GS:

ADP-12CB Rev. B/Delta, ADP-12CB Rev. C, WP10XY/Dow Dec, HES 10-311/Hitron.

For UL CSA Listed products, the adapter shall be UL, CUL, or CSA Listed Class 2

Power Supply.

Part No.: 830504-00

FCC Declaration of Conformity

Declares that the products:

Product Name: Color Scanner Model No.: Umax Astra 600P, H5E0

Accessories: Transparency Adapters Model No.: UTA-2A, H760

FCC Rules: Tested to comply with FCC Part 15, Class B Op. Environment: For home or office use

FCC Compliance Statement:

This device complies with part 15 of the FCC Rules. Operation is subject to the following

conditions: (1) This device may not cause harmful interference, and (2) This device must accept

any interference receiver, including interference that may cause undesired operation.

Information to user:

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular

installation, if this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

1. Reorient/Relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment to an outlet different from the one to which the receiver is connected.

4. Consult the dealer or an experienced radio/TV technician for help.

Caution:

Changes or modifications not expressly approved by the manufacturer responsible for compliance

could void the user’s authority to operate the equipment.

The party responsible for product compliance:

Corporate Name: UMAX Technologies, Inc.

Address: 10460 Brockwood Dr.; Dallas, TX 75238; U.S.A.

Telephone No.: 214-342-9799

Contents

Preparation for Installation …………………………………………………………… 4

Installation on Macintosh ……………………………………………………………… 9

Installation on PC …………………………………………………………………….. 10

Completing First Scan ………………………………………………………………... 12

Troubleshooting ………………………………………………………………………. 14

Maintenance …………………………………………………………………………... 15

Specifications ………………………………………………………………………….. 16

Glossary ……………………………………………………………………………….. 17

Trademarks

IBM PC/AT is a trademark of International Business Machines Corporation. MS-Windows, Windows, and

MS-DOS are trademarks of Microsoft Corporation. Macintosh and MacSeries are trademarks of Apple

Computer, Inc. Photoshop is a trademark of Adobe Systems, Inc. Other names and trademarks appearing

herein are trademarks of their respective holders.

Preparation for Installation

Unpacking the Scanner

Please remove all packing materials from the scanner. Check if any damage has occurred during shipment

while you are unpacking the scanner. If you notice any damage, notify your dealer at once. Remember to

save all shipping and packing materials if you want to transport the scanner in the future.

Please find the following items in your scanner box:

1. UMAX Color Scanner

2. UMAX Scanner CD

3. SCSI Cable

4. Power Adapter

5. Manuals

6. SCSI Terminator

7. SCSI Interface Card (for PC only)

Unlocking Your Scanner

Before using your scanner ensure that the carriage lock is in the unlocked position. Likewise, turn the

restraint toward to the locked position, to avoid damaging the internal optics during transportation.

! Warning:

You must lock your scanner before transporting it, failure to do so can cause extensive damage to your

scanner. Ensure that the scanner’s optical assembly is secure and the lamp is in the home position before

locking your scanner.

Power on Your Scanner

Once the scanner has been unpacked and the optical assembly has been unlocked, the scanner is ready to

perform this test.

To power on the scanner, do the following:

1. Connect the power adapter to the scanner.

2. Connect the power adapter to a wall outlet.

3. Turn on the scanner’s power switch.

Wait for the Ready indicator to glow. When the Ready indicator has stopped blinking, the scanner

is ready for you to scan images.

4. Your hardware is installed. Once your software is installed, you can begin scanning.

Changing the SCSI ID Number

If you have other devices connected to your SCSI port, you need to check and see what SCSI ID’s are

already used. The scanner is preset at the factory to SCSI ID 5.

If, after checking other devices in the SCSI chain, you find that SCSI ID 5 is unused, you do not need to

change the ID on the scanner and you can go ahead with the installation.

If, however, after checking other devices in the SCSI chain, you find that another device uses SCSI ID 5,

you must change the SCSI ID on your scanner.

To change the SCSI ID, do the following:

1. Make sure the scanner is turned off.

2. Gently turn the switch until an unused number appears in the switch’s notch.

Note: Do not use SCSI ID 8 and 9 on your scanner. They are for factory use only.

Installation on Macintosh

Connecting the Scanner and your Macintosh

When the scanner’s SCSI ID is properly set (see “Changing the SCSI ID Number” section for instructions

on setting the scanner’s SCSI ID), do the following to connect the scanner to your computer:

1. Turn off your computer and unplug the power cord.

2. Locate the SCSI Cable. Connect the 25-pin cable connector to the Macintosh SCSI port.

3. Attach the other end of the cable to one of the SCSI ports on your scanner.

4. If your scanner is not chained to other SCSI devices, please connect the Terminator to the

remaining SCSI port of your scanner.

5. Connect the power adapter to the scanner.

6. Turn on the computer.

Installing the Scanner Drivers for Macintosh

Install the image editing software included with your scanner. Refer to the instructions included with the

appropriate software.

To install the scanner drivers, do the following:

1. Turn on your computer.

2. Install your image editing software first. (e.g. Photoshop, PhotoDeluxe, etc.)

3. Insert the UMAX Scanner CD into your CD-ROM drive.

4. Double-click on the UMAX Scanner CD Installer icon.

5. Follow the on-screen instructions to complete the installation.

6. Procedures on how to use the bundled software are provided in the Quick Start Guide.

Installation on PC

Interface Card Installation

Follow the steps below to install the card into an available 16-bit expansion slot*:

1. Turn off your computer and unplug the power cord.

2. Remove the housing cover from the computer. (Follow the instructions provided in the computer’s

reference manual).

3. Unscrew and remove the expansion slot cover from an empty expansion slot.

4. Gently insert the interface card into the slot until it is firmly seated in the slot.

5. Secure the card’s mounting bracket in place with the screw from the expansion slot cover.

6. Replace the housing cover. (Following the instructions provided in the computer’s reference

manual).

Warning: Static electricity can cause severe damage to your computer system and scanner, review

the section entitled “Maintenance: Static Electricity Precautions.”

* Your scanner connects to your computer via a SCSI connection. A proprietary card is provided to

make this connection. If you have an Adaptec compliant card already installed in your computer go to

next section “Connecting the Scanner and your PC”.

Connecting the Scanner and Your PC

Now that the interface card has been installed in the computer, the scanner can be connected. To connect

the scanner and computer, do the following:

1. Turn off your computer and unplug the power cord.

2. Locate the supplied SCSI Cable. Connect the 25-pin cable connector to the interface card you just

installed in your PC.

3. Attach the other end of the cable to one SCSI port of your scanner.

4. If your scanner is not chained to other SCSI devices or is the last device on the SCSI chain, please

connect the Terminator to the remaining SCSI port of your scanner.

5. Connect the power adapter to the scanner.

6. Turn on the scanner

7. Turn on the computer.

Inhaltsverzeichnis

Andere UMAX Technologies Scanner Handbücher

UMAX Technologies

UMAX Technologies PowerLook 1000 Bedienungsanleitung

UMAX Technologies

UMAX Technologies PowerLook 3000 Bedienungsanleitung

UMAX Technologies

UMAX Technologies Astra 610S Bedienungsanleitung

UMAX Technologies

UMAX Technologies Astra 2100U Bedienungsanleitung

UMAX Technologies

UMAX Technologies PowerLook 1000 Bedienungsanleitung

UMAX Technologies

UMAX Technologies AstraNET e5420 Bedienungsanleitung

UMAX Technologies

UMAX Technologies Astra 3400 Bedienungsanleitung

UMAX Technologies

UMAX Technologies Astra 1600U Bedienungsanleitung

UMAX Technologies

UMAX Technologies Astra MX3 Bedienungsanleitung

UMAX Technologies

UMAX Technologies PowerLook 1120 Bedienungsanleitung

UMAX Technologies

UMAX Technologies Astra 2400S Bedienungsanleitung

UMAX Technologies

UMAX Technologies Astra 2200 Bedienungsanleitung

UMAX Technologies

UMAX Technologies Astra 4400 Bedienungsanleitung

UMAX Technologies

UMAX Technologies Astra 1220 Series Bedienungsanleitung

UMAX Technologies

UMAX Technologies PowerLook 180 Bedienungsanleitung

UMAX Technologies

UMAX Technologies AV210 Bedienungsanleitung

UMAX Technologies

UMAX Technologies Mirage II Bedienungsanleitung

UMAX Technologies

UMAX Technologies 2000U/P Bedienungsanleitung

UMAX Technologies

UMAX Technologies PowerLook PowerLook III Bedienungsanleitung

UMAX Technologies

UMAX Technologies PowerLook 1100 Bedienungsanleitung

UMAX Technologies

UMAX Technologies Astra 6400 Bedienungsanleitung

UMAX Technologies

UMAX Technologies Astra 1220 Series Handbuch

UMAX Technologies

UMAX Technologies AstraNET e3420 Bedienungsanleitung

UMAX Technologies

UMAX Technologies AstraNET e3420 Bedienungsanleitung

Beliebte Scanner Handbücher anderer Marken

Plustek

Plustek Scanner Bedienungsanleitung

Z/I Imaging

Z/I Imaging PhotoScan 2001 Bedienungsanleitung

Renkforce

Renkforce DS100-5M Bedienungsanleitung

Image Access

Image Access WideTEK A2 Bedienungsanleitung

Canon

Canon imageFORMULA CR-120N Bedienungsanleitung

Fujitsu

Fujitsu FI-4860C2 Bedienungsanleitung

GeoSlam

GeoSlam ZEB Horizon Montageanleitung

Kodak

Kodak i5800 Scanner Bedienungsanleitung

Kodak

Kodak i7300 Bedienungsanleitung

Revopoint

Revopoint POP Bedienungsanleitung

Fujitsu

Fujitsu fi-4860C Bedienungsanleitung

Eddyfi Technologies

Eddyfi Technologies Floormap X Bedienungsanleitung

Faselase

Faselase F6 Bedienungsanleitung

Fujitsu

Fujitsu CardMinder Bedienungsanleitung

Uniden

Uniden BC340CRS Bedienungsanleitung

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Bedienungsanleitung

Mustek

Mustek PageExpress 4800 Pro Bedienungsanleitung

Optex

Optex 750830 Bedienungsanleitung