Uniden DSS 7805 WP Bedienungsanleitung
DSS7805WP
Accessory Waterproof
handset for
DSS7800 Series
ELITE Series
DSS7900 Series
Welcome
Congratulations on your purchase of the Uniden DSS7805WP acces-
sory waterproof handset and charger. You can place this fully featured
cordless handset anywhere your home has AC power even outside by
the pool!
Notes:
Illustrations in this manual are used for explanation purposes.
Some illustrations may differ from the actual unit.
JIS7 Specs is a water submersion standard. The cordless
handset is designed to withstand submersion in water at a
depth up to 1metre for a duration up to 30 minutes.
Important!
The DSS7805WP accessory handset will not operate until it is
registered to a Uniden main base. This can be done after activating and
then charging the handset. This manual describes how to set up your
new handset and use its key functions. For more detailed instructions
on operating your new handset, please refer to the manual supplied
with your base as the functions available on the DSS7805WP handset
are set by the main base at time of registration.
•
•
1
Terminology Used in this Manual
Base The main part of the phone that connects to
your phone line and lets you make and receive
calls.
Charger A cradle that charges an accessory handset. It
connects to power but not to a phone line.
Accessory Handset A handset that works with an expandable
phone base. Accessory handsets must be
registered to a base.
Standby The handset is not in use. If it is off the cradle,
no line has been activated. No dial tone is
present.
Station Any handset or the base.
Talk A telephone line has been activated on the
handset or the base, enabling a dial tone.
Compatible Bases
Your phone is compatible with the following Uniden 5.8 GHz Digital
Expandable Systems:
Please visit our website at; Australian model: www.uniden.com.au ,
New Zealand model: www.uniden.co.nz for the most up-to-date list of
compatible bases.
2
DSS7960+1
DSS7915+1
DSS7955
DSS7955+1
DSS7955+2
DSS7815
DSS7815+1
DSS7855
DSS7855+1
DSS7855+2
ELITE8815
ELITE8815+1
ELITE8855
ELITE8855+1
Installing the Accessory Handset
Checking the Package Contents
Make sure your package contains the following items. If any items are
missing or damaged, contact your place of purchase.
Activate the handset
The handset is powered by a rechargeable
battery pack already installed in the handset’s
battery compartment. Before charging the bat-
tery for the st time, push the pin for activation,
located on the bottom of the handset (see label
with instructions). Once activated, remove the
label and pin and then place the handset in the
charger.
Notes:
Use only the Uniden (BT-446)
rechargeable battery pack supplied with
your cordless telephone.
Caution:
Keep magnetic items away from the
handset.
Don’t place the handset where it will be
subjected to direct sunlight for long periods
of time.
•
•
•
Cordless Handset
Charging Cradle
AC adaptor, model
No: AAD-7805WP
Input: 240V AC 50Hz
Output: 21V DC 100 mA
•
•
•
Rechargeable NiMH Battery
Pack, model No: BT-446
Capacity: 800 mAh, 3.6V
Beltclip
Printed Material
•
•
•
3
Charging the Accessory Handset
The handset is powered by a rechargeable battery pack that automati-
cally recharges when the handset is placed in the charger. Unlike your
typical household phone chargers, your new waterproof accessory
handset uses an enclosed charging method called magnetic inductive
charging. This type charger allows us to charge your handset without
exposing any electronic components; therefore, making it safer to use
around water or in highly humid environments.
1. Connect the AC adapter to the
DC IN 21V jack and to a 240V
AC outlet that is not controlled
by a wall switch.
Caution: Use only the
Uniden AAD-7805WP adapter.
2. Set the charger on a desk or
tabletop, and place the handset
in the charger with the
keypad facing forward.
3. Make sure that the charge LED illuminates. If the LED does not
illuminate, check to see that the AC adapter is plugged in.
4. Charge the handset battery pack for at least 25 hours before using
your new handset for the rst time.
Notes:
The charger is not water submersible. Wipe off dirt or shake
water from handset before placing in the base.
Due to the enclosed type of magnetic inductive charging used
with this model, it will be normal for the bottom of the handset
tobewarmerthanroomtemperaturewhenyourstremove
it from the charging cradle. However, the warmth should not be
excessive or uncomfortable to touch.
•
•
4
Registering the Handset
You must register the handset to the base before you can use it. Only
one handset can be registered at a time. (If an accessory handset has
previously been registered to a base, you must reset the handset before
you can register it to a new base.)
1. Select your base model from this list and follow these directions:
MODEL DIRECTIONS:
DSS7815
DSS7815+1
DSS7915+1
DSS7855
DSS7855+1
DSS7855+2
DSS7960+1
DSS7955
DSS7955+1
DSS7955+2
5
Make sure there is no handset sitting in the
main base charger before starting.
Disconnect the base AC adapter.
While holding the[ndhandset], reconnect
the AC Adapter.
On the handset, press and hold[#] until the
display reads HANDSET REGISTERING
and you hear a beep.
Make sure there is no handset sitting in the
main base charger before starting.
Disconnect the base AC adapter.
While holding the[ash/ndhs], reconnect
the AC Adapter.
On the handset, press and hold[#]until the
display reads HANDSET REGISTERING
and you hear a beep.
•
•
•
•
•
•
•
•
Make sure there is no handset sitting in the
main base charger before starting.
• On the base, press the MENU soft key.
• Scroll down to REGISTER HANDSET and
press the OK soft key.
• On the handset, press and hold [#] until the
display reads HANDSET REGISTERING and
you hear a beep.
•
2. When REGISTRATION COMPLETE. is displayed; the handset
has been registered to the base. If REGISTRATION FAILED.
appears, please try these steps again.
6
ELITE8855
ELITE8855+1
Make sure there is no handset sitting in the
main base charger before starting.
From the base, press [menu/select] and select
System Setup menu.
Select Register Handset, and press
[menu/select].
On the handset, press and hold the [#] key until
the display reads HANDSET REGISTERING
and you hear a beep.
•
•
•
•
ELITE8815
ELITE8815+1
Make sure there is no handset sitting in the
main base charger before starting.
Press and hold the Registration button at the
underside of the base.
Keep pressing the Registration button until the
handset charge LED on main base starts to
blink.
On the handset, press and hold the [#] key until
the display reads HANDSET REGISTERING
and you hear a beep.
•
•
•
•
Replace the rechargeable handset battery pack
1. Remove the 4 screws holding the
battery compartment with a screwdriver
and take off the battery cover. Remove
the old battery pack in the battery
compartment.
2. Plug the replacement battery
connector (red & black wires) into the
small, black jack inside the battery
compartment. (The connector notches
t into the grooves of the jack only
one-way.) Match the wire colors to
the polarity indicated in the battery
compartment, connect the battery and
listen for a click to insure connection.
3. Make certain you have made a good
connection by slightly pulling on the
battery wires. If the battery connector is
not securely connected, the handset will
not charge properly.
4. Before placing the battery cover back on
the handset, make sure there is no
foreign matter under the rubber seal
located on the under side. By
inserting the bottom rst, place the
battery cover back on the handset and
tighten the 4 screws.
Recheck that the screws are
tightened. You may void the Warranty
if the battery cover is not screwed on
rmlyandmoistureallowedto
seep in.
If the rubber seal appears worn, nicked,
or dried out, replacement seals are
available. Please see our website at;
Australian model: www.uniden.com.au ,
New Zealand model: www.uniden.co.nz.
Rubber Seal
7
Notes:
If there is any foreign matter on the rubber seal located on
the under side of the battery cover, the handset may not
be water resistant.
The rubber seal should be kept clean and replaced every 2
years to ensure the handset is water resistant even if the
seal does not look worn.
• Do not place an excessively dirty handset in the base.
Shake excess water from handset prior to placing back in the
charging cradle.
Installing the Belt Clip
Line up the tabs with the holes on each
side of the handset. Press the belt clip
down until both tabs click into place.
To remove the belt clip, pull both sides
of the clip to release the tabs from the
holes.
Resetting Handsets
If you want to register the handset to a different base or replace a hand-
set with another one, you must rst clear the registration information
from the base and the handset.
1. Press and hold[]and[#]
for at least 5 seconds, until the
SYSTEM RESET menu appears.
2. Select the DEREGISTER HS submenu. WHICH HANDSET?
appears in the display.
3. Move the cursor to select the handset ID to be de-registered from
the list, and then press the OK soft key. DEREGISTER HS
appears.
4. Move the cursor to select YES, and then press the OK soft key.
When ARE YOU SURE? appears, select YES. You will hear a
conrmation tone.
•
•
•
9JKEJ*CPFUGV!
*CPFUGV
*CPFUGV
$#%- $#%- 1-
8
Resetting the Handset without the Base
If the original base this handset was registered to is not available for
some reason (for example, it is lost or somehow incapacitated), you can
still reset the handset and use it with another base.
1. Press and hold[]and[#] for more than 5 seconds, until the
SYSTEM RESET menu appears.
2. Select the BASE UNAVAILABLE submenu. BASE UNAVAILABLE
appears in the display.
3. Move the cursor to select YES, and then press the OK soft key.
When ARE YOU SURE? appears, select YES. You will hear
a conrmation tone, and the handset deletes its own link to the base
without trying to contact the base.
Now you are ready to register the handset to the new base.
9
Inhaltsverzeichnis
Andere Uniden Zubehör Handbücher
