Uniden GNC 701 Bedienungsanleitung

Quick-Start Guide

GNC 701/710

IP Camera

Use this Quick-Start Guide to connect the camera to the network

and for basic installation and setup procedure. For more detailed

instructions refer to the online Owner’s Manual on the Uniden

website www.uniden.com.au. This quick start guide is for reference

only. Slight difference may be found in user interface.

In the Box

Model GNC701 GNC710

QSG 1 1

Mounting Screw

Kit

1 1

Installation

Position Map

1 1

Hex wrench 1 -

If any item is missing or damaged, contact your place of purchase

immediately. Never use damaged products!

Need help? Get answers at our website:

www.uniden.com.au for Australian model

1. Do not drop, puncture or disassemble the camera.

2. DO NOT expose the camera to excessive water or moisture.

3. Never tug on the power cable to unplug from the power outlet. Always

grasp the AC adapter when unplugging.

4. Do not expose the camera to high temperature or leave it in direct

sunlight. Doing so may damage the camera or cause camera

temporary malfunction.

5. For your own safety, avoid using the camera or power off the camera

when there is a storm or lightning.

6. Remove the power adaptor during long periods between usages.

7. Use only the accessories and power adaptors supplied.

8. Please use correct power supply to operate the device

Important Safety Instructions

Getting to know your GNC701

1 Dome cover

2 Dome enclosure

3 Power Port

4 I/O Port

5 Network Port

6 Audio Input Port

7 Audio Output Port

8 Reset Button

9 SD Card Slot

GNC701 Installation

Step 1: Use the included inner hex

wrench to unfasten the dome enclosure.

Step 2: Install Micro SD card (optional).

Step 3: Place and stick the installation

position map on the ceiling or the wall to

suit your desired location.

Step 4: Find and drill the small cross

signs on the map to fit three plastic

expansion bolts holes. Insert the

expansion bolts into the holes.

Step 5: Position the dome body to

match the three screw holes. Fasten

the installation screws to secure the

dome body onto the ceiling or wall. Do not let the cable get caught in between the dome body

and the wall.

Step 6: Adjust the lens viewing direction by rotating the LED cover or rotate the dome bracket

or tilt it vertically. Range of adjustment: vertical (0°~64°), horizontal (0°~355°) & image rotation

(0°~355°).

Step 7: Put on back the dome enclosure according to the hole and fasten the three inner hex

screws firmly.

Getting to know your GNC710

1 Bullet cover

2 Network Port

3 Power Port

4 Reset Button

5 SD Card Slot

6 SD Card (not included)

7 Cover Plate

8 Cover Screw

GNC710 Installation

Step 1: Open the cover plate to insert SD Card (optional)

Step 2: Place and stick the installation position map on the ceiling or the wall to suit your desired

location.

Step 2: Mark and drill holes on the wall or ceiling.

Step 2: Insert the expansion bolt into the hole.

Step 3: Fasten the installation screws to secure the device on the wall or ceiling. You may move

device the cover back and forth and tighten the it.

Step 4: Please use screwdriver to loosen the adjusting screw and adjust the camera to desired

viewing direction and tighten back the screw.

Network Port Water Resistant Seal (Optional)

If you powered your camera over PoE, you can further protect it from water. You need a cabler

installer for this purpose.

Step 1: Fix the rubber ring into the network pork. Keep the smaller diameter hole outwards.

Step 2: Install the rubber ring into the main body of water resistant connector.

Step 3: Pull the Ethernet cable without Ethernet connector through the main body of water

resistant connector, fixing rubber ring and cover.

Step 4: Install the Ethernet connector onto the Ethernet cable.

Step 5: Connect the Ethernet Connector onto the network port.

Step 6: Pull and place the water resistant connector on the network port and rotate it clockwise

to lock firmly.

Step 7: Place the cover on the water resistant connector and rotate it clockwise to lock firmly.

Reset the Camera

To reset the GNC 701/710, press and hold the ‘Reset’ button for 10

seconds, then only release the ‘Reset’ button.

Troubleshooting

If... Try This...

The NVR cannot find

the camera

Make sure your network supports DHCP

protocol.

Make sure that the DHCP option is turned on.

Make sure the camera and your NVR

connected to the same switch/router.

Make sure the switch/router is properly

powered on.

Make sure the camera is properly powered on.

Make sure the WiFi router has enabled SSID

broadcasting.

The camera does not

obtain an IP address

Please reset the camera and try again.

Make sure the camera was powered up

correctly.

Connect the camera directly to NVR.

Please test it with another Ethernet cable.

Make sure the camera has the same subnet

mask and gateway as the NVR/switch/router.

As the Uniden App is constantly under development to enrich user

experience, the icons/screens shown in this QSG may vary slightly from

the actual app. This QSG uses icons from the iPad app.

Adding GNC 701/710 to existing GNVR 86xx /

87xx / 167xx System using a switch/router.

Please use PoE supported switch/router if you only want to power the

camera using Ethernet cable (not included) otherwise please supply

power using a power adapter (not included). Please make sure the NVR

and camera are on the same network/switch/router.

For more detailed instructions or modification refer to the online

Owner’s Manual for GNVR 86xx/87xx/167xx series on the Uniden

website www.uniden.com.au to add IP Camera into existing setup .

1. Right click with your mouse on the NVR live view interface to view

menu options. Select Remote Device to add GNC 701/710 into the

system.

3. Click IP search to search the IP address of GNC 701/710.

4. Once the GNC 701/710 IP address found, tick the device. You may

tick more devices if you have 2 or more GNC 701/710 connected to

the same network. Click Add to add selected device(s) to the Added

Device list.

5. When status showing green dot indicates the connection is good while

red dot indicates connection failed. You may click in the Added

Device box to edit GNC 701/710 password if the connection fail or

showing invalid password at live view interface. The default password

is “admin”.

6. Right click the mouse button to exit Remote Device window.

2. Remote Device window shows up.

is quick start guide is for reference only. User interface may be dierent from actual product.

If there is any unclear or controversy, please visit Uniden website or call Uniden Australia.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Uniden Sicherheitskamera Handbücher

Uniden

Uniden ULC58 Bedienungsanleitung

Uniden

Uniden APPCAM23 Service-Handbuch

Uniden

Uniden UDW10055 Benutzerhandbuch

Uniden

Uniden App Cam Solo+ Bedienungsanleitung

Uniden

Uniden Guardian App Cam Solo Bedienungsanleitung

Uniden

Uniden UDR744 Bedienungsanleitung

Uniden

Uniden UDS655 Bedienungsanleitung

Uniden

Uniden LightCam 40HD Bedienungsanleitung

Uniden

Uniden UDSC15 Bedienungsanleitung

Uniden

Uniden AppCam 25HD Bedienungsanleitung

Uniden

Uniden App Cam Floodlight Bedienungsanleitung

Uniden

Uniden App Cam Solo PT Bedienungsanleitung

Uniden

Uniden App Cam 4K Bullet-S Bedienungsanleitung

Uniden

Uniden App Cam Pano Series Bedienungsanleitung

Uniden

Uniden AppCam 4OPT Bedienungsanleitung

Uniden

Uniden APP CAM 25 HDA Bedienungsanleitung

Uniden

Uniden Pro710NPTZC Bedienungsanleitung

Uniden

Uniden Guardian GC45 Service-Handbuch

Uniden

Uniden APPCAM25HD Bedienungsanleitung

Uniden

Uniden UDS655 Bedienungsanleitung

Uniden

Uniden AppCam 50HD Bedienungsanleitung

Uniden

Uniden UDWC25 Bedienungsanleitung

Uniden

Uniden App Cam Home+ Bedienungsanleitung

Uniden

Uniden App Cam Spotlight+ Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung