Uplift Desk PDC003 Bedienungsanleitung
Package Contents
Clamp-on or Under-Mount Power with USB
SKU: PDC003
Clamp Assembly
Under Desk Assembly
Step 1
Loosen the thumbscrews and slide the unit onto your desktop.
It will t on desks up to 1.75” thick.
After ensuring the Clamp bracket is ush against the desk,
tighten the thumbscrews to secure it in place.
Step 1
UPLIFT Desktops have pre-drilled holes on the left and right
side for attaching a keypad. You can use one of these sets of
holes to attach the Desktop bracket.
If you don’t have an UPLIFT Desktop or if you want to mount
the unit in a location other than one of the keypad mounting lo-
cations, place the bracket where you want it and make a pencil
mark at each hole location. Make sure the Desktop bracket is
aligned as shown and ush with the front edge of the desktop.
If you own a drill, you can make this a little easier by drilling
pilot holes where you’ve made your pencil marks using a 1/8”
diameter bit.
Note: DRILL NO DEEPER THAN 1/2”. To ensure this, we
recommend wrapping a piece of tape around your drill
bit 1/2” from the tip. Stop drilling just before the tape
touches the desktop.
Install the four Woodscrews as shown to attach the
Desktop bracket to the desktop. Make sure the screws are fully
installed and ush with the bracket, but be careful to not over-
tighten them to avoid stripping.
Step 2
Plug the unit into a nearby 120V wall outlet. The power cord is
10’ long; if installing on a height adjustable desk, make sure it
has enough slack to raise and lower your desk safely and com-
pletely without straining the cord.
1/2’’
Main Unit with Clamp bracket
(as shipped)
Desktop bracket 2.5 mm Allen wrenchWood screw
(qty 4)
CAUTION: Read all instructions before assembly. Failure to assemble properly may result in
damage or personal injury.
CAUTION: To avoid overheating and possible damage to this product and other equipment,
do not use to power a device which exceeds the designed ratings.
CAUTION: This product must be installed and/or used in accordance with the
appropriate electrical codes and regulations. Plug into 120V grounded outlet only.
WARNING: Avoid getting any liquid on the unit, as it can cause shock & re. If unit gets wet,
disconnect the power at the circuit breaker, fuse or outlet. Ensure the unit
is completely dry before connecting this product to a power source.
WARNING: If unit fails to operate, it should be discarded. Do not open the unit or try to service it.
CAUTION: The UPLIFT Clamp-on Power with USB needs a path to ground to work properly,
and should only be plugged directly into a grounded outlet. Using any extension cord in con-
junction with an UPLIFT Clamp-on Power with USB will void all UPLIFT warranties. All con-
nected equipment should be plugged directly into your UPLIFT Clamp-on Power with USB.
CAUTIONS & WARNINGS
!
!
!
!
!
!
!
Copyright Notice:
This guide is a component of the Clamp-on Power with USB. This guide is a part of the scope of delivery, even if the item is resold. This guide is also available on the UPLIFT Desk website: upliftdesk.com. Excerpts or
copies may not be forwarded to third parties or used in any other published form without the prior written consent of UPLIFT Desk.
These instructions are subject to United States copyright law.
©
AI-PDC003-2.1
Step 3
After removing the two brackets that shipped installed to the
Main unit, slide the Main unit onto the installed Desktop bracket
as shown.
Once the Main unit is aligned underneath the Desktop bracket,
reinstall two of the Set screws removed in the previous step to
lock the unit in place and keep it from sliding off the Desktop
bracket.
Step 2
Use the 2.5mm Allen wrench to remove all four Set screws from
the two brackets that shipped installed on the Main unit. Then
slide the two brackets off of either side of the unit. Keep two of
the Set screws for use in the next step.
Note: these brackets may be tight but they will come off.
Inhaltsverzeichnis
Andere Uplift Desk Zubehör Handbücher
