VADDIO IntelliSHOT Bedienungsanleitung
Using the IntelliSHOT Auto-Tracking Camera
Customize this document to create a guide that's specific to your IntelliSHOT installation.
Front of the Camera
The camera is available in black or white.
Camera and zoom lens – Up to 30x zoom.
Integrated microphone – No external microphone needed in typical installations. Echo-canceling microphone
picks up the voices of participants up to 10 ft. (3 m) away.
Status lights – The illuminated trim detail on the camera's face indicates the camera's current state. The status
lights can be turned off in the administrative web interface.
Pivoting head – Manually tilt the head as needed.
Note
By default, the camera's status lights are active during normal operation; however, they can be
configured to remain off when the camera is powered up. The camera may be sending video even if the
lights are off.
Document 411-0053-40 Rev A, May 2021
About Manual Operation
When you need to control the camera in manual mode rather than using Autoframing, you can use
nThe RF remote
nThe web interface (accessible from your computer's browser or using a Vaddio Device Controller)
nA third-party control device
When you use the manual controls, Autoframing pauses. It's similar to cruise control in a car:Using a preset or
directional control is like tapping the brake pedal. The camera remains under manual control until you resume
Autoframing.
Operating the Camera from the Web Interface
The web interface is available on the Vaddio Device Controller touch panel (if your installation uses one) or from
a computer’s web browser.
The operator's Camera page provides most of the same controls as the remote:
nAudio and video mute
nCamera standby
nPan, tilt, and zoom
nCamera presets, if any have been stored
nCustom color/lighting settings, if any have been stored
If your installation does not include a Vaddio Device Controller or other control surface, contact the system
administrator to find out how to access the web interface.
2
Muting Audio and Video
Use the audio mute button to stop sending audio. Use the video mute button to temporarily stop sending video
from the camera without placing it in standby.
Use the RF remote to control volume.
Managing the Camera Ready State
Use the Standby button to switch between low-power (standby) and ready states.
Moving the Camera
Use the arrow buttons for camera pan and tilt.The center button moves the camera to the home position.
Zooming In or Out
Use the Zoom + button to zoom in and the Zoom– button to zoom out.
Moving the Camera to a Preset Position
Use the Preset buttons (if available)to move the camera to any of its programmed positions. Presets are only
available if they have been set in the administrative interface or with the RF remote.
3
Operating the Camera with the RF Remote
The RF remote provides basic in-conference functionality – pan, tilt, zoom, presets, volume control, and muting.
You can also use it to get the camera's IP address. When you have the IP address, you can open the camera's
web interface.
Before you can use the remote, you will need to:
nInstall the batteries
nPair the remote with the camera
IntelliSHOT cameras are not compatible with IRremotes.
Installing the Batteries
The remote uses two AAA batteries.
1. Remove the cover from the back of the remote. You may need to press down on the inner edge while
sliding it off.
2. Install the batteries as shown in the diagram in the battery opening.
3. Slide and snap the cover back into place.
Pairing the Remote to the Camera
The camera does not recognize or respond to the remote until they are paired. Do this after the camera is
turned on and its status light is white.
1. Press and hold the IP button on the connector panel until the status light blinks cyan.
2. While the status light blinks cyan, press the pairing button on the remote. The camera's status light
changes to steady white when the pairing is complete. You may need to press the remote's pairing
button more than once.
3. If the status light changes from blinking cyan to blinking blue, this indicates a pairing error: The pairing
was not successful and pairing mode has timed out. Go back to step 1. If the problem persists, contact
Vaddio Technical Support.
4
RF Remote Quick Reference
Indicator and Power button – Set the camera to standby mode,
or return to full-power mode.
Function buttons – Reserved for future use.
Arrow buttons – Pan and tilt. Autoframing pauses if you use
these buttons.
Home button – Resumes Autoframing if it is paused.
Network button – Display the camera's IP address on the video
output.
Pairing button – Use when pairing the remote with the camera.
Mute button – Mute the microphone(s).
Reserved for future use.
Volume +/– button – Increase or decrease the volume from the
connected speaker.
Focus +/– buttons – Adjust the focal distance in or out, when
Manual focus mode is selected.
Zoom +/– button– Increase or decrease the zoom.
Auto and Man buttons – Select automatic or manual focus.
Preset buttons – Set, clear, or select preset shots. Autoframing
pauses if you use these buttons.
Other Things to Know About the Remote
Here are some common situations in which the remote can behave in ways you don't expect.
Environments with cameras in adjacent rooms – If the remote is currently paired to a camera and within range
of that camera, it will not pair with another camera.
The remote goes to standby mode after a brief period of inactivity – To return the remote to its normal
operating state, press a button.
5
Vaddio is a brand of Legrand AV Inc.· www.legrandav.com · Phone 800.572.2011 / +1.763.971.4400 · Fax
©2020 Legrand AV Inc.
Legrand AV Inc. grants permission to customers and end users to incorporate the content of this document into
their own branded guides for using the equipment described herein. For other uses, please contact Legrand AV
Vaddio is a registered trademark of Legrand AV Inc. All other brand names or marks are used for identification
purposes and are trademarks of their respective owners. All patents are protected under existing designations.
Other patents pending.
6
Andere Handbücher für IntelliSHOT
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere VADDIO Sicherheitskamera Handbücher
VADDIO
VADDIO WALLVIEW DVI/HDMI HD-20 Bedienungsanleitung
VADDIO
VADDIO RoboSHOT 12E HDBT Bedienungsanleitung
VADDIO
VADDIO CeilingVIEW 70 PTZ HideAway Bedienungsanleitung
VADDIO
VADDIO POWERVIEW HD-22 QSR Bedienungsanleitung
VADDIO
VADDIO RoboSHOT 12E USB Bedienungsanleitung
VADDIO
VADDIO IntelliSHOT 999-21100-000 Bedienungsanleitung
VADDIO
VADDIO ZOOMSHOT 20 Bedienungsanleitung
VADDIO
VADDIO WallVIEW D80 PTZ Bedienungsanleitung
VADDIO
VADDIO 999-6900-000W Bedienungsanleitung
VADDIO
VADDIO VADDIO/CANON BU Series Bedienungsanleitung
VADDIO
VADDIO DOMEVIEW HD Bedienungsanleitung
VADDIO
VADDIO WALLVIEW DVI/HDMI HD-20 Bedienungsanleitung
VADDIO
VADDIO RoboSHOT HDBT Series Bedienungsanleitung
VADDIO
VADDIO ZOOMSHOT WALLVIEW SR 999-6918-001 Bedienungsanleitung
VADDIO
VADDIO PowerVIEW HD-22 Bedienungsanleitung
VADDIO
VADDIO CLEARVIEW HD-20SE Bedienungsanleitung
VADDIO
VADDIO RoboSHOT 12 Bedienungsanleitung
VADDIO
VADDIO BU-45H Bedienungsanleitung
VADDIO
VADDIO WallVIEW PRO 300 Bedienungsanleitung
VADDIO
VADDIO WALLVIEW HD-22 Bedienungsanleitung
