VarTech Systems DiamondVue VT201C Bedienungsanleitung

VT201 DiamondVue User Guide 150-021

VT201 DiamondVue Series

20.1” Flat Panel Series LCD Monitors

VT201C · VT201R

VT201P · VT201PSS

VT201W · VT201M · VT201MF

Transflectives:

VT201CTSR · VT201PTSR

VT201PSSTSR · VT201RTSR

VarTech Systems Inc.

Solutions for Demanding Applications

Industrial CRT and Flat Panel Displays

User’s Guide

Read these instructions completely before attempting to operate your new Color Display.

Table Of Contents

Page Page

Section 1 Section 4

Introduction 1 Touch screen 10

1.1 About LCD Monitors 1 4.1 Introduction 10

1.2 Product Safety Precautions 2 4.2 Installation 10

Section 2 Section 5

Display Setup 3 Troubleshooting Tips 11-12

Display Features 3

2.1 Unpacking The Display 4 Section 6

2.2 Included Parts 4 Cleaning & Maintenance 13

2.3 Connecting Your Display 4

2.4 Signal Connections 4-5 Section 7

Mechanical Drawings 14

Section 3 7.1 Panel Mount Procedure 14

Getting Started 6 20.1” Chassis Mount Mechanical Drawing 15-18

3.1 Adjusting the Display 6 20.1” Panel Mount Mechanical Drawing 19-20

3.2 Adjustment Procedure 7-9 20.1” Rack Mount Mechanical Drawing 21

20.1” Wall Mount Mechanical Drawing

20.1” Foxboro Configured Mechanical Drawing 22

Section 8

Display Specifications 23

VT201 DiamondVue User Guide 150-021

LCDs

INTRODUCTION

Section

About LCD Monitors

What you gain by using an LCD monitor in your industrial controls

are the future of display technology. CRTs although they have

dropped in cost significantly, do not offer the performance, reliability,

and mounting options available with LCDs. LCD monitors consist

primarily of an LCD, Video Board and a Back Light video. The LCD

determines to a large extent the viewing angle, brightness and contrast. Beyond that it is the

function of the video board which converts the analog RGB (Red, Green, Blue) signals from a

standard video card to a high quality, digital RGB that the LCD can display.

Recently the video card has taken on a new role. It is the responsibility of this device to “scale” a

particular video resolution to the “native” resolution of the LCD. Simply, consider that a computer is

putting out a VGA [640x480] resolution signal, yet the LCD that is connected is an XGA

[1024x768] display. The displayed picture would be in the center 1/3 of the LCD. With the

introduction of the scaling engine. The converter will mathematically recalculate the 640x480 to

1024x768. This may sound simple but it is in fact a complex algorithm that adjusts for different

aspect ratios and pixel alignment, essentially smoothing text and graphics to produce a picture

that is pleasant to the eye.

All Vartech displays from 12.1” (800x600) to 23.1 (1600x1200) incorporate scaling engines in the

converter card.

1.1

Product Safety Precautions

 Ensure that sufficient space is available around the display to provide the circulation

necessary for cooling.

 Ensure that the ambient air temperature will not exceed the specified maximum

temperature.

 Do not attempt to service this display yourself. The rear chassis has a seal so that non

qualified personal will not expose themselves to dangerous voltages or other risks.

 To protect from electrical shock, unplug the display power supply from the wall before

moving.

 Do not expose the display to direct sunlight or heat.

 Do not use this display near water

 Do not place any heavy objects on the power cords. Damage may cause electrical shock.

 Unplug the power supply from the wall or unit if one of the following conditions exists.

 Power cord or plug is damaged or frayed

 Liquid is spilled into the display or the display is exposed to rain or water.

 The display does not operate normally when the operating instructions are

followed.

 The display has been dropped or the enclosure has been damaged.

 The display exhibits a distinct change in performance, indicating a need for

service.

1.2

VT201 DiamondVue User Guide 150-021

Section

2 DISPLAY SETUP

DISPLAY SETUP

VT201 Series Display Features

 Capable of displaying unlimited colors in a continuous spectrum. The high contrast LCD

enhances the image with no geometric distortion.

 The VT201 DiamondVue Series directly accepts an analog 5 wire RGB with separate H/V sync

or 4 wire RGB with separate combined sync or 3 wire SOG.

 The VT201 DiamondVue Series is auto synchronous adjusting the display to the appropriate

input between VGA, SVGA,XGA, and SXGA.

 The VT201 DiamondVue Series is supplied with a Anti-Reflective Screen unless equipped with

an optional Touch System.

 The VT201 DiamondVue Series has an integrated 115/220VAC or 90/264VAC supply as stan-

dard on all models.

2.1

 VT201C, VT201P, VT201P-SS, VT201R, VT201MF, VT201W, VT201M LCD Monitor or

VT201CTSR, VT201PTSR, VT201PSSTSR, VT201RTSR Transflective

 5 ft Video Cable

 10-32 Mounting Hardware. (For use with Panel Mount only)

 6 ft RS232 or USB Touch Interface Cable (Optional when touch is installed)

 CD ROM with Touch Screen Drivers (Optional when touch is installed)

 Users Guide (Printed or on CD)

2.2 Unpacking and setting up your display

Your LCD monitor package will consist of the components listed below. Open shipping

container and lay all components on a flat clean surface.

2.3 What is included with your display

2.4 Connecting the Display

1. Connect all cables to the computer first. This would include the VGA cable and the optional

RS 232 serial or USB touch screen connection.

2. After connecting the cables between the LCD monitor and the computer, plug the customer

supplied +12VDC or 90/264 VAC source to the 12V connection on the rear.

3. Once the +12V connection is made, the display is active.

4. If your computer was off, turn on your computer.

5. Your display should now operate as a normal computer display showing your windows or

whatever video is being sent to the flat panel.

Note: If for any reason the display goes blank and gives an “out of Range” or “No Input Signal”,

your computer or video source is putting out a signal that is out of range of the LCD’s video

board. If this happens, reboot the computer or video source and make sure you are inputting

the correct signal. If the display doesn’t work properly, it may be because:

(a) The resolution is to high or low for the LCD.

(b) The refresh rate is set to high. Refresh on an LCD is different than a CRT. Set the refresh to

60Hz. CRT’s need a high refresh rate to avoid flicker. The refresh rate has no impact on

LCD’s.

(d) The unit is malfunctioning. If you believe this to be true, disconnect the video cable from the

rear of the LCD and connect to a known good computer CRT display. If the computer

display is working satisfactory and the video is within the appropriate range, then contact

Vartech Customer service for a RMA number at 800-223-8050.

2.5 Signal Connections

To avoid irregular operation and /or damage to the display, please insure correct video is being

supplied as shown on the following page.

VT201 DiamondVue User Guide 150-021

2.5 Signal Connections Cont.

Standard Resolution Supported

 640 x 480 (VGA)

Pin assignments for the HD15

video connector.

1 Red Video

2 Green Video

3 Blue Video

4 Not Used

5 Return

6 Red Video Ground

7 Green Video Ground

8 Blue Video Ground

9 No Connection

10 Sync Ground

11 Not Used

12 Bi-Directional Data

13 Horizontal Sync

14 Vertical Sync

15 Data Clock (SCL)

Composite Video Input Connector: CVBS 1.0V p-p

S-Video: S-VHS

LUMA Signal Input 0.7V p-p

CHROMA Signal Input 0.7V p-p

You can use an HD-15 connector cable or a BNC adapter cable to connect the flat panel

monitor to the host computer. The HD-15 video cable (supplied in the kit) you use with this

monitor is equipped with a conventional HD-15 connector at each end.

Note:

The following figure is the view looking into the pin end of the male connector or solder term

end of the female connector.

Optional BNC Adaptor Cable

A 5BNC-to-HD15 adapter cable is available. The functions of the cables are described below.

 R, B, and G: Red, Green, and Blue input connectors to establish color.

These are used for RS-343 analog signals.

 HS/CS: Separate horizontal/composite sync signal from the video

source.

 VS: Separate vertical sync signal from the video source.

BNC Adapter Cable

This table describes the signal types you can use with the connectors:

2.5 Signal Connections Cont.

BNC Signal Type Description R G B HS/ CS VS

Sync-on-Green

(Not Available)

Use the three video connectors.

Horizontal and vertical syncs are

supplied on the green video line. X X X

Composite Sync

(Not available)

Use the three video connectors

plus the horizontal sync/

composite sync input X X X X

Separate Horizontal

and Vertical Sync.

Use the three video connectors

plus the horizontal sync/

composite sync and vertical sync

input.

X X X X X

BNC Signal Types

VT201 DiamondVue User Guide 150-021

Vartech Systems, Inc

Menu Select Down Up Input

Section

3.1 Adjusting the display

The VT201 DiamondVue Series display has an embedded microprocessor in the converter

card. Once you have the unit displaying the resolution you desire for your application do the

following:

In order to navigate to the appropriate adjustments, press Menu and the OSD layout chart will

appear as indicated as shown below.

Definition of OSD (on screen display) Adjustments

There are seven membrane buttons (as shown above) located on the unit. They will activate

the OSD and allow navigation to all adjustments if your unit requires adjustment.

Press MENU and a major adjustment category will appear. Press DOWN or UP and you will

see the remaining adjustment categories. The actual adjustment categories are listed under

each major category (bold) as shown below.

ADJUSTMENT

Brightness, Contrast, Clock, Phase, H Position, V Position, Auto

COLOR ADJUSTMENT

User, 6500, 9300

SETUP

Language, Image Size, OSD H Position, OSD V Position, Transparency, Zoom

PIP - Picture in Picture

PIP On / Off, PIP Source, PIP Size, PIP H Position, PIP V Position, PIP Image

3.2

GETTING STARTED

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere VarTech Systems Monitor Handbücher

VarTech Systems

VarTech Systems VT14A-D Bedienungsanleitung

VarTech Systems

VarTech Systems ColorVue VT190PC Bedienungsanleitung

VarTech Systems

VarTech Systems VT064C Bedienungsanleitung

VarTech Systems

VarTech Systems DiamondVue VT190C Bedienungsanleitung

VarTech Systems

VarTech Systems VT29B-M Bedienungsanleitung

VarTech Systems

VarTech Systems VT20A Bedienungsanleitung

VarTech Systems

VarTech Systems VT520 Bedienungsanleitung

VarTech Systems

VarTech Systems VT420D Bedienungsanleitung

VarTech Systems

VarTech Systems VT121CC Bedienungsanleitung

VarTech Systems

VarTech Systems VTPC2100VS Bedienungsanleitung

VarTech Systems

VarTech Systems VT420W Bedienungsanleitung

VarTech Systems

VarTech Systems GDM-5001PT Bedienungsanleitung

VarTech Systems

VarTech Systems VT084XHB Bedienungsanleitung

VarTech Systems

VarTech Systems VT121 DiamondVue Series Bedienungsanleitung

VarTech Systems

VarTech Systems VT420 Series Bedienungsanleitung

VarTech Systems

VarTech Systems VT190PVS Bedienungsanleitung

VarTech Systems

VarTech Systems VT213C Bedienungsanleitung

VarTech Systems

VarTech Systems VT14B-C1 Bedienungsanleitung

VarTech Systems

VarTech Systems VT190P2 Bedienungsanleitung

VarTech Systems

VarTech Systems VT170W Bedienungsanleitung

VarTech Systems

VarTech Systems VT150CHB Bedienungsanleitung

VarTech Systems

VarTech Systems VT320D Bedienungsanleitung

VarTech Systems

VarTech Systems VT181R2 Bedienungsanleitung

VarTech Systems

VarTech Systems VT084XA4 Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung