Vaultek PROMXI Bedienungsanleitung

Toggle LCD Brightness 19

Toggle Bluetooth® 20

Toggle Smart Key Modes 20

Toggle DMT Sensitivity 20

Toggle Dual Entry Mode 20

Vaultek™ App Features / App Pairing 21 / 22

Securing Your Safe 23

Modular Interior 23

Adjust Interior Shelf Height 23

Product Registration 24

FAQ 25 / 26

Troubleshooting 27

Customer Support / Warranty 28

Table of Contents

Product Overview 01 / 04

Introduction / Warnings 05 / 06

Battery Operation / Battery Maintenance 07 / 09

Battery Installation 07

Charging the Battery 08

Master Code Programming 10

Smart Align Biometric Programming 11 / 14

Helpful Programming TIPS 11

Programming 1st and 2nd Fingerprints 12

Programming Additional Fingerprints 3-20 13

Deleting Fingerprints 14

Smart Key Operation / Smart Key Warnings 15 / 18

Smart Key Pairing 15

Toggle Smart Key Access Modes 16

To Unpair Smart Key 16

Multiple Safe Management 17

Hot Keys 18 / 20

Tamper Detection 18

Toggle Stealth Mode 18

Toggle Travel Mode 19

View Battery Status 19

Delete Fingerprints 19

Toggle Interior Light 19

Box Contents

Vaultek™ MXi Safe

Smart Key and Battery

Rechargeable Battery

AC Power Adapter and Charging Cable

Tutorial Videos

Listed below are some of the various tutorials available at vaulteksafe.com under Support/Tutorials.

Programming and Setup

Twin Pistol Rack

Hardware Mounting Kit

Owner's Manual / Quick Start Guide

Backup Keys (2)

+ More videos online.

06. Safe Status

07. Safe Name

08. Battery Level

04. Numeric Keypad

05. Micro-USB Charging Port

01. Smart Align Biometric Scanner

02. Silicone Key Hole Cover

03. LCD Screen

09. Bluetooth®

10. Smart Key

11. Impact Detection

12. Sound

13. Interior LED

LCD Screen Format

09 10 11 12 13

14. Adjustable Shelf 16. PROGRAM Button

17. Pre-Drilled Mounting Holes

15. Module System

(Twin Pistol Rack)

18. LED Light Button

19. Battery Compartment

1816

Smart Align Biometric Scanner: Personalized access for up to 20 unique ngerprints. See pages 11 to 14 for

more information.

Keypad: The numeric keypad responds quickly for rapid access and has a built-in proximity sensor that lights up

when your hand brushes against the safe. See page 10 for more information.

The Vaultek™ MXi is a biometric, PIN access / Bluetooth® access safe. Its solid structure and penetration

resistant design makes it ideal for storing valuables such as rearms, jewelry, cash, and other personal items.

Smart Key: Remote for on demand access. See page 15 and 18 for more information.

Vaultek™ App: Open the safe with the Bluetooth app. See pages 21 and 22 for more information.

DMT (Impact Detection): Motion activated alarm can be disabled or enabled with three levels of

sensitivity (Low, Medium, and High) using the Vaultek™ app or hot key functions. See page 20 for information.

IMPORTANT Check page 18 for Smart Key warnings.

CONSEQUENTIAL, ARISING OUT OF THE USE OF, OR THE INABILITY TO USE THE VAULTEK™ SAFE.

The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of

such marks by Vaultek Safe, Inc. is under license.

Battery Operation

Your safe uses a 3.7V 18650 rechargeable lithium-ion with a at

top. A minimum 2000 mAh capacity is required, however 2200

mAh or higher can be used to increase operation time.

Battery Installation

To get started, insert one of your backup keys into the keyhole at

the top of the safe (see Figure A). Push key in and rotate the key

90 degrees clockwise to open the safe.

Locate the battery compartment inside the safe beneath the

control panel (see Figure B).

Remove the battery cover by pressing down on the tab near the

top of the cover.

Insert the 18650 rechargeable lithium-ion battery (included in

accessory box) into the battery compartment. Note that your

Vaultek™ safe automatically detects the polarity of the battery

and can be installed in either direction.

When the battery is inserted you will hear a short welcome tone

and the keypad will light up.

Once you hear the tone replace the battery cover. You are now

ready to program your safe.

Charging the Battery

Your Vaultek™ safe is powered by a rechargeable

lithium-ion battery and comes with a charging kit

which includes an AC power adapter and a micro-USB

cable. Safe and micro-USB cable can be used with all

international power adapters.

Under normal usage, a fully charged battery can last

2 months. To recharge the safe, plug the micro-USB

cable into the micro-USB receiving jack located on the

lower right side of the safe (Figure C) and connect to

a standard USB port or wall outlet using the AC power

adapter. Approximate recharge time is 2.5 hours.

When charging the LED light above the micro-USB jack

(Figure C) will be on.

Due to the powerful features within the MX Series it is

recommended to keep the safe plugged in. A specially

designed VT powerpack is available as a separate

accessory to extend operation time 4 to 5 months.

Continue on next page for more information about the battery.

Battery Maintenance

Testing the Battery Power

To check the battery level, press and hold '6' and '8' key together on the keypad for 3 seconds.

Master Code Programming

First time users should change the default code as soon as possible to prevent unauthorized access to your safe.

You will also use this master code to pair the Vaultek™ app on your smartphone, so it should be kept

condential.

TIP: Code Requirements

Enter default code 1-2-3-4 on the keypad to open your safe.

With the safe open, press and hold the '1' key then the

"PROGRAM" button together (3 seconds)(Figure D) until all

status bar LEDs turn RED and let go.

Enter your NEW master code.

Press and hold the '1' key then the "PROGRAM" button together

again (3 seconds) until all status bar LEDs turn RED and let go.

Enter your NEW master code a second time.

Press and hold the '1' key then the "PROGRAM" button together a third time (3 seconds) until the safe beeps and

all status bar LEDs turn GREEN and let go. This tone conrms that the password has been reset.

If you make a mistake and the new code will not work, simply start over with step 2.

Your code can be a minimum of 4 and a maximum

of 8 digits. We recommend a code 6 to 8 digits in

length using at least one of each key to make it more

dicult for someone to guess your code. For your

security, the safe will time out and sleep if 6 or more

incorrect entries are made.

Two keys cannot be pressed simultaneously.

Programming a new code will overwrite your

previous code.

TIP! The Vaultek™ app will ask for your safe’s master

code during pairing and anytime you change the

code the app will ask you to re-enter it.

IMPORTANT

Replace the battery when one or more of the following occurs: A) all four of the white LEDs above the micro-USB

jack and blinking or B) it takes than 4 hours to recharge the battery.

Use a 3.7V 18650 rechargeable lithium-ion battery with a at top. A minimum 2000 mAh capacity is required,

however 2200 mAh or higher can be used to increase operation time.

A high capacity battery upgrade is available as an accessory through our website.

The adapter used to charge the battery should output 5V/2000mA or above when using micro-USB.

Continue on next page for more information about the ngerprint scanner.

Programming the 1st and 2nd Fingerprints

The 1st and 2nd ngerprints will be recognized as administrative ngerprints and will be used to authorize

additional users.

Open the safe. Program 1st ngerprint by pressing and

holding the '2' key then the "PROGRAM" button together

(3 seconds)(Figure G) until the screen prompts you to scan

the 1st of ve scans.

Using the helpful programming tips provided on page 11

place your nger on the ngerprint scanner for the 1st of

ve scans. When the safe beeps, and the screen prompts

the next scan remove your nger. If the screen indicates a

failed to complete then start over with step 1.

Place nger again over the scanner until the safe beeps

and the screen prompts the next scan and lift. You will

repeat this process until all scans (1-5) are programmed.

Close lid and test to see if the safe will open using your ngerprint. If you experience issues refer to the helpful

programming tips listed on page 11 or check our tutorials online at vaulteksafe.com under Support/Tutorials.

Repeat steps 1 through 4 to add the 2nd administrative ngerprint.

Continue on next page to program ngerprints 3-20.

Helpful Programming TIPS

Place the core of the ngerprint at (Figure E+F) over

the center of the scanner in line with the side LEDs (this

allows the scanner to read where most of the ngerprint

detail is located) see (Figure E).

Adjust your nger slightly between scans for increased

accuracy.

Excessive moisture, lotions, or dirt will aect your

ngerprint and may cause inaccurate sensor reading.

If you are experiencing diculty try dierent ngers.

Each nger is unique and some ngers, such as your

thumb, contain more readable information than others.

To increase success rate register the same ngerprint

multiple times.

ATTENTION! (Figure F)

Position your nger at against the scanner to

increase the amount of readable information.

FIGURE G

authorized users have access to your valuables. The safe is capable of storing ngerprint data for up to 20 unique

Press and hold the '3' key then the "PROGRAM" button together until the safe beeps and the screen prompts you

to enter your master code.

Enter your master code on the keypad. If the code is correct, the safe will beep and the screen will indicate

deletion of all of the ngerprints.

Smart Align Biometric Programming

Programming Additional Fingerprints 3-20

The rst two ngerprints programmed into the safe are the administrative ngerprints. Any additional users

programmed require authorization from one of these ngerprints.

Open the safe. Program additional ngerprints by pressing and holding the '2' then "PROGRAM" button together

(3 seconds)(Figure G on page 12). The screen will prompt you to scan one of the administrative ngerprints.

Place one of the rst two programmed administrative ngerprints on the scanner and remove when the safe

beeps and screen authorizes the print. You can now program a NEW ngerprint.

TIP: If the administrative print is left on the scanner too long the safe will begin to program that ngerprint into

the safe again and not the NEW ngerprint. If this happens start over with step 1.

Using the helpful programming tips provided on page 11 place the NEW nger on the scanner. When the safe

beeps and the screen prompts the next scan remove your nger.

Place nger again over the scanner until the safe beeps and the screen prompts the next scan and lift. You will

repeat this process until all scans (1-5) are programmed.

Inhaltsverzeichnis

Andere Vaultek Andere Handbücher

Vaultek

Vaultek VT20i Bedienungsanleitung

Beliebte Andere Handbücher anderer Marken

GO Industries

GO Industries 38017 Bedienungsanleitung

Cissell

Cissell 30LBCMAN2 Bedienungsanleitung

RIDGID

RIDGID K-60SP Bedienungsanleitung

Gage Bilt

Gage Bilt GB751SH-5 Bedienungsanleitung

OVE

OVE SIERRA 60 Bedienungsanleitung

ReelCraft

ReelCraft 7800 OLB21 Bedienungsanleitung

Body Armor 4x4

Body Armor 4x4 ECO-SERIES Bedienungsanleitung

ROBLIN

ROBLIN DROP Benutzerhandbuch

EMG

EMG EMG-ACB BARREL Service-Handbuch

MiniSolar

MiniSolar MT-150 Bedienungsanleitung

Parkside

Parkside PSZ 250 B2 Bedienungsanleitung

ABB

ABB REM 610 Produkthandbuch

Parkside

Parkside 55992 Betriebsanleitung

Skyjacker

Skyjacker F250 Bedienungsanleitung

IBM

IBM IBM SYSTEM Z Installationsanleitung

Grech Motors

Grech Motors G28 Bedienungsanleitung

NOVAK

NOVAK BATTERY CARE SHEET Leitfaden

Telemotive

Telemotive blue PiraT Mini Benutzerhandbuch