Velleman CAMCOLBUL28Z Bedienungsanleitung

CAMCOLBUL28Z

1/3" HIGH RESOLUTION SONY EFFIO DSP CAMERA WITH

72 IR LEDs

1/3" HR SONY EFFIO DSP CAMERA MET 72 IR-LEDS

CAMÉRA 1/3" HR SONY EFFIO DSP AVEC 72 LEDS IR

CÁMARA 1/3" DE ALTA RESOLUCIÓN SONY EFFIO DSP CON

72 LEDs IR

1/3" HOCHAUFLÖSENDE SONY EFFIO DSP-KAMERA MIT

72 IR-LEDs

USER MANUAL 3

GEBRUIKERSHANDLEIDING 13

NOTICE D’EMPLOI 23

MANUAL DEL USUARIO 34

BEDIENUNGSANLEITUNG 44

CAMCOLBUL28Z

V. 01 –13/06/2013 2 ©Velleman nv

video

power

voeding

vídeo

vidéo

alimentación

alimentation

Video

Stromversorgung

CAMCOLBUL28Z

V. 01 –13/06/2013 3 ©Velleman nv

USER MANUAL

1. Introduction

To all residents of the European Union

Important environmental information about this product

This symbol on the device or the package indicates that disposal of

the device after its lifecycle could harm the environment. Do not

dispose of the unit (or batteries) as unsorted municipal waste; it

should be taken to a specialized company for recycling. This device

should be returned to your distributor or to a local recycling

service. Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.

Thank you for choosing Velleman! Please read the manual thoroughly before

bringing this device into service. If the device was damaged in transit, don't

install or use it and contact your dealer.

2. Safety Instructions

Keep the device away from children and unauthorised users.

Risk of electric shock when opening the cover.

DO NOT disassemble or open the cover. There are no user-

serviceable parts inside the device. Refer to an authorized dealer

for service and/or spare parts.

3. General Guidelines

Refer to the Velleman® Service and Quality Warranty on the last pages

of this manual.

Familiarise yourself with the functions of the device before actually

using it.

All modifications of the device are forbidden for safety reasons. Damage

caused by user modifications to the device is not covered by the

warranty.

Only use the device for its intended purpose. Using the device in an

unauthorised way will void the warranty.

Damage caused by disregard of certain guidelines in this manual is not

covered by the warranty and the dealer will not accept responsibility for

any ensuing defects or problems.

Keep this device away from extreme heat.

CAMCOLBUL28Z

V. 01 –13/06/2013 4 ©Velleman nv

Protect this device from shocks and abuse. Avoid brute force when

operating the device.

DO NOT use this product to violate privacy laws or perform other illegal

activities.

4. Features

weatherproof

with B/W night vision (IR LEDs)

super high resolution

special functions via on-screen display (OSD) set-up menu

oshutter / AGC

owhite balance.

5. Overview

Refer to the illustrations on page 2of this manual.

IR LEDs

bracket

lens

zoom and focus adjust

light sensor

camera bolt

sunshield

6. Hardware installation

Refer to the illustrations on page 2of this manual.

Choose a location for the camera, keeping following guidelines in mind:

odo not install the camera in locations where extremely high or low

temperatures or excessive vibrations may occur.

oavoid mounting the camera near high electro-magnetic fields.

odo not aim the camera at the sun or other extremely bright objects

or reflections (e.g. metal doors).

Use the mounting bracket [5] to determine the location of the mounting

holes. Drill the holes and secure the bracket [5] using screws.

Attach the camera to the mounting bracket [5] with the camera

bolt [7].

Connect the power connector [B] to the 12VDC power supply (not incl.).

Connect the BNC connector [A] to a monitor (not incl.).

Point the camera towards the field of interest and tighten the position

bolt.

Manually adjust the zoom and focus with the screws [6].

CAMCOLBUL28Z

V. 01 –13/06/2013 5 ©Velleman nv

7. OSD Settings

There is a small joystick in the camera cable that allows you to adjust the

settings of the camera using an on-screen display (OSD).

Press the middle button to access the menu, or to

select an option.

Press the up and down buttons to move up and

down in the menu.

Press the left and right buttons to modify the menu

parameters.

In the OSD menu:

NEXT/BACK: select this option and press the middle button to go to the

next/previous page of options in the menu.

RETURN: select this option and press the middle button to return to the

previous level in the menu.

EXIT: select this option and press the middle button to leave the OSD

menu without saving the settings.

SAVE ALL: select this option and press the middle button to save all

settings.

CAMERA RESET: select this option and press the middle button to reset

the camera to the factory defaults.

The OSD menu settings are described in detail below.

7.1 Lens

The LENS menu is not applicable to this camera. You can leave the settings

as they are.

7.2 Shutter/AGC

Use this menu option to control how the camera responds to high and low

light settings using auto-gain and shutter settings. You can choose

automatic or manual control. Automatic control is usually sufficient for most

environments.

Display: SHUTTER/AGC

AUTO

SETUP

MODE = SHUT: the camera adjusts the image by changing

the shutter speed. You can configure high and low luminance

conditions.

HIGH LUMINANCE: use this to adjust bright images.

BRIGHTNESS: Set the brightness level for high luminance

mode. Default setting is 24.

Note: if you adjust this setting, we recommend that you do it

when there is a lot of light available.

CAMCOLBUL28Z

V. 01 –13/06/2013 6 ©Velleman nv

LOW LUMINANCE: use this to adjust dim images using

automatic gain control.

MODE: set to AGC to use automatic gain control. Set to

OFF to switch automatic gain control off.

BRIGHTNESS: Set the brightness level for low luminance

mode.

If you want to adjust this setting, we recommend that you do it

when it is very dark (night).

Note: AGC can introduce more noise in the image.

MANUAL

Use manual mode only in environments with the exact same

amount of light throughout the day. We recommend using the

automatic mode even under such conditions.

Note: if the scene becomes brighter or dimmer, the camera

will not adjust and the image may be over- or underexposed.

MODE = SHUT + AGC: you can set the shutter speed and

AGC as specified below:

SHUTTER: set the shutter speed between 1/50 and

1/10000. The slower the shutter speed, the brighter the

image. Faster shutter speeds are used if you want to

capture fast moving objects with less motions blur.

AGC: set the AGC between 6 and 44.8 dB.

7.3 White balance

Use this menu options to define the white balance adjustment.

Display: WHITE BAL

ATW

ATW = auto-tracking white balance. White balance makes sure

that white objects are always reproduced correctly. The ATW

option controls the automatic white balance adjustments. For

most environments, the default settings are sufficient.

SPEED: controls how fast the camera will adjust the white

balance. The higher the setting, the faster the adjustment.

Note: a too fast adjustment can result in colour oscillation.

DELAY CNT: specifies how often the camera checks for

colour changes and apply the ATW settings. The lower the

number, the more frequent the checks and adjustments.

ATW FRAME: sets the frame magnification for the camera to

identify the colour changes. (Recommended setting is 1.0.)

ENVIRONMENT: choose INDOOR for indoor environments,

and OUTDOOR for outdoor environments.

PUSH

This is a fixed setting.

CAMCOLBUL28Z

V. 01 –13/06/2013 7 ©Velleman nv

USER1

USER2

These are two user-definable setting that let you control red and

blue gain. This can be useful in environments that are saturated

with a single colour of light (for example bars or entertainment

venues), or it can help vision-impaired (colour-blind) users.

ANTI CR

Anti colour rolling. Some types of lighting can cause colour bars

rolling over the screen. Use this setting to compensate.

MANUAL

When you switch the camera on, it will acquire a white balance

value from the whitest object in view. The camera will then

reproduce white colour based on this value, regardless of

changes in colour temperature or other factors. If this value

gives insufficient colour quality, you can manually adjust the

balance between red and blue levels to improve the image.

PUSH

LOCK

Use this option to adjust white balance based on a white object

that you use as a baseline. Point the camera at the white object

and make sure it fills as much of the screen as possible. Click the

middle button on the joystick. The camera will now use the

colour of that white object as a baseline.

7.4 Back light

If there is a bright light in the background, for example from a window, the

image around it may be too dim to see clearly. In that case, use the

backlight function to compensate.

Display: BACKLIGHT

OFF

No backlight compensation

BLC

Back light compensation. The camera automatically brightens the

dim parts of the image.

HLC

Highlight compensation. Use this setting to compensate for extreme

differences between dark and light areas. For example, if someone

shines a bright light directly into the lens, the entire image can

become overexposed. With HLC, the camera masks the bright area

so that the area around the light source is still visible.

7.5 Picture adjustment

These are the common adjustments for video images: MIRROR to mirror

the image, BRIGHTNESS (brightness), CONTRAST (contrast),

SHARPNESS (sharpness), HUE (hue), and GAIN (gain).

7.6 ATR

Use the Adaptive Tone Reproduction (ATR) function to improve the colour

tones of subjects in images that contain both bright and dim areas (for

example, a wall with a window).

CAMCOLBUL28Z

V. 01 –13/06/2013 8 ©Velleman nv

Note: ATR can introduce noise in night-time images.

Display: ATR

OFF

ATR is switched off

ATR is active. Use the settings below.

LUMINANCE: Use this setting to adjust luminance.

CONTRAST: Use this setting to adjust contrast.

7.7 Motion detection

Use this function to see motion detection during live monitoring. You can

use:

Block display: in a grid of squares, select the areas where you want to

use motion detection. If the camera detects motion in one of the enabled

squares, the image in that square will ‘flash’.

Monitor area selection: you can select up to 4 separate areas for motion

detection. If the camera detects motion, the outer edge of the area will

‘flash’.

Display: MOTION DET

OFF

Motion detection is switched off

Motion detection is active. Use the settings below.

DETECT SENSE: Set the motion detection sensitivity. With a higher

sensitivity, slighter movements will be detected.

BLOCK DISP: block display. Use this option to select squares in a

grid for motion detection.

1. Set BLOCK DISP to ENABLE and press the middle button. The

grid appears on the screen. Use the navigation buttons on the

joystick to select the squares and click the middle button to

enable/disable each of them for motion detection. Motion is

detected in the squares that show the grid. Motion is not

detected in squares that show the camera image without grid.

When you have finished, press and hold the middle button for

3 seconds, then release.

2. Next, set BLOCK DISP to ON.

3. To disable block display, set BLOCK DISP to OFF.

MONITOR AREA: use this option to select a predefined rectangular

area for motion detection. You can define up to 4 areas.

1. First, set MONITOR AREA to ON.

2. Select which of the 4 areas you want to define in AREA SEL

(1/4 …4/4).

3. Use the TOP, BOTTOM, LEFT, and RIGHT settings to define the

top, bottom, left, and right edge of the area.

CAMCOLBUL28Z

V. 01 –13/06/2013 9 ©Velleman nv

7.8 Privacy

Use this function to block a part of the image where you don’t want to view

activity. For example, if part of the image shows a public area where

recording may be illegal. You can define up to 8 areas.

Display: PRIVACY

OFF

Privacy is switched off

Privacy function is active. Use the settings below.

Select which of the 8 areas you want to define in AREA SEL

(1/8 …8/8).

Use the TOP, BOTTOM, LEFT, and RIGHT settings to define the

top, bottom, left, and right edge of the area.

COLOR: sets the colour of the privacy area.

TRANSP: sets the transparency for the privacy area.

MOSAIC: creates a mosaic pattern in the privacy area. This is

useful if you want to make an area private, but still want to use

it for motion detection.

7.9 Day / night

The camera can switch automatically between colour images in day

conditions and black-and-white images in night conditions. Use this function

to control the day/night behaviour of the camera.

Note: black-and-white images are much clearer and contain less noise at

low light levels.

Display: DAY/NIGHT

COLOR

The camera always makes colour images.

B/W

The camera always makes black-and-white images.

BURST: you can switch burst on or off to improve the image

quality. The burst function sends a colour signal to the

monitor in B/W mode. This may degrade the clarity of the

image.

AUTO

The camera makes colour images during the day and black-and-

white images during the night. Use the settings below.

BURST: you can switch burst on or off to improve the image

quality. The burst function sends a colour signal to the

monitor in B/W mode. This may degrade the clarity of the

image.

DELAY CNT: delay counter. Defines the delay before the

camera switches from day to nigh mode or vice versa. This

prevents the camera from switching over too quickly if the

light conditions change only briefly.

DAYNIGHT: sets the threshold for switching from day to

night mode. The lower the setting, the less light is required

CAMCOLBUL28Z

V. 01 –13/06/2013 10 ©Velleman nv

to switch to night mode. Recommended settings are 40-75

for indoors, and 150 for outdoors.

NIGHTDAY: sets the threshold for switching from night to

day mode. The higher the setting, the more light is required

to switch to day mode. Recommended settings are 50-85 for

indoors, and 175 for outdoors.

Remarks:

The DAY>NIGHT setting must always be lower than the

NIGHT>DAY setting.

Make sure that the difference between the two settings is

large enough. If the settings are too close together, the

camera will switch too often between the two modes.

7.10 Noise reduction

Use this function to set the noise reduction mode.

Display: NR

OFF

Noise reduction is switched off.

Use only luminance (Y) noise reduction.

Use only colour (C) noise reduction.

Y/C

Use both luminance (Y) and colour (C) noise reduction

(recommended setting).

Set Y LEVEL for luminance and C LEVEL for colour noise reduction.

7.11 Camera ID

Use this function to give the camera a name. The name will appear on the

monitor. You can define where the name appears on the screen.

Display: CAMERA ID

OFF

No name for the camera.

You can enter two lines of 26 characters for the camera name.

Note: make sure that CHR1 is selected.

Position the cursor in the text line by selecting the arrow icons

 on the OSD screen.

Use the navigation buttons on the joystick to select the

characters for the name. Press the middle button to confirm and

move to the next character.

Select CLR to delete a character.

Select POS to position the name on the monitor. Use the

navigation buttons on the joystick to move the text to the

desired position, and press the middle button to confirm.

Inhaltsverzeichnis

Sprachen:

Andere Velleman Sicherheitskamera Handbücher

Velleman

Velleman Etiampro ECAMTVI101 Bedienungsanleitung

Velleman

Velleman CAMCOLD16 Bedienungsanleitung

Velleman

Velleman CAMCOLBUL2N Bedienungsanleitung

Velleman

Velleman CAMCOLBUL2 Bedienungsanleitung

Velleman

Velleman CAMCOLD3 Bedienungsanleitung

Velleman

Velleman ECAMIP501 Bedienungsanleitung

Velleman

Velleman camcolvc21 Bedienungsanleitung

Velleman

Velleman CAMSETW12 Bedienungsanleitung

Velleman

Velleman CAMCOLD12 Bedienungsanleitung

Velleman

Velleman CAMIP1 Bedienungsanleitung

Velleman

Velleman CAMTVI13 Bedienungsanleitung

Velleman

Velleman CAMSETW6 Bedienungsanleitung

Velleman

Velleman EtiamPro ECAMIP601 Bedienungsanleitung

Velleman

Velleman CAMTVI7N2 Bedienungsanleitung

Velleman

Velleman CAMTVI10 Bedienungsanleitung

Velleman

Velleman CAMCOLBUL5H4 Bedienungsanleitung

Velleman

Velleman CAMCOLD21 Bedienungsanleitung

Velleman

Velleman CAMD3 Bedienungsanleitung

Velleman

Velleman CAMCOLD1 Bedienungsanleitung

Velleman

Velleman CAMCOLMHA8 Bedienungsanleitung

Velleman

Velleman CAMCOLVC1 Bedienungsanleitung

Velleman

Velleman CAMD13 Bedienungsanleitung

Velleman

Velleman CAMTVI16N Bedienungsanleitung

Velleman

Velleman CAMCOLBUL23 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung