Vents TT PRO Series Bedienungsanleitung

INLINE MIXEDFLOW FANS

User’s manual

www.vents-us.com

TT PRO

CONTENTS

Delivery set................................................................................................................................................................................................................7

Brief description .....................................................................................................................................................................................................7

Operation guidelines ..........................................................................................................................................................................................8

Installation .................................................................................................................................................................................................................8

Technical maintenance......................................................................................................................................................................................9

Storage and transportation regulations..................................................................................................................................................10

Manufacturer’s warranty...................................................................................................................................................................................11

This user’s manual is a main operating document intended for technical, maintenance, and operating staﬀ.

The manual contains information about purpose, technical details, operating principle, design, and installation

of the TT PRO unit and all its modiﬁcations.

Technical and maintenance staﬀ must have theoretical and practical training in the ﬁeld of ventilation systems

and should be able to work in accordance with workplace safety rules as well as construction norms and

standards applicable in the territory of the country.

All user’s manual requirements as well as the provisions of all the

applicable local and national construction, electrical, and technical

norms and standards must be observed when installing and

operating the unit.

Disconnect the unit from the power supply prior to any connection,

servicing, maintenance, and repair operations.

Only qualied electricians with a work permit for electrical units

up to 1000 V are allowed for installation and maintenance. The

present user’s manual should be carefully read before beginning

works.

Check the unit for any visible damage of the impeller, the casing, and

the grille before starting installation. The casing internals must be free

of any foreign objects that can damage the impeller blades.

While mounting the unit, avoid compression of the casing!

Deformation of the casing may result in motor jam and excessive

noise.

Misuse of the unit and any unauthorised modiﬁcations are not

allowed.

Do not expose the device to adverse atmospheric agents (rain, sun,

etc.).

Transported air must not contain any dust or other solid impurities,

sticky substances, or ﬁbrous materials.

Do not use the unit in a hazardous or explosive environment

containing spirits, gasoline, insecticides, etc.

Do not close or block the intake or extract vents in order to ensure the

eﬃcient air ﬂow.

Do not sit on the unit and do not put objects on it.

The information in this user’s manual was correct at the time of the

document’s preparation.

The Company reserves the right to modify the technical

characteristics, design, or conﬁguration of its products at any time in

order to incorporate the latest technological developments.

Never touch the unit with wet or damp hands.

Never touch the unit when barefoot.

This appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a person

responsible for their safety.

Children should be supervised to ensure that they do not play with

the appliance.

If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent, or similarly qualiﬁed persons in order

to avoid a safety hazard.

If the cord set is damaged, it must be replaced by a special cord set

available from the manufacturer or its service agent.

THE PRODUCT MUST BE DISPOSED SEPARATELY AT THE END OF ITS SERVICE LIFE.

DO NOT DISPOSE THE UNIT AS UNSORTED DOMESTIC WASTE.

CAUTION: In order to avoid a safety hazard due to inadvertent

resetting of the thermal cut-out, this appliance must not be supplied

through an external switching device, such as a timer, or connected

to a circuit that is regularly switched on and oﬀ by the utility.

Ensure that the appliance is switched oﬀ from the supply mains

before removing the guard.

Precautions must be taken to avoid the back-ﬂow of gases into the

room from the open ﬂue of gas or other fuel-burning appliances.

DELIVERY SET

Fan — 1 pc.

Screws and dowels — 4 pcs.

Plastic screwdriver (for models with a timer) — 1 pc.

User’s manual — 1 pc.

Packing box — 1 pc.

BRIEF DESCRIPTION

The product described herein is a mixed-ﬂow inline fan for supply or extract ventilation of premises.

The fan is designed for connection to ø 100, 125 and 150mm air ducts.

The unit is equipped with a two speed motor.

INSTALLATION

The fan is suitable both for horizontal or vertical mounting on the ﬂoor, on the wall or on the ceiling (Fig. 1).

The fan can be installed independently or as part of a set with parallel or in-series connection (Fig. 2).

Install minimum 3.28 ft long air duct on the intake spigot side in case of horizontal fan mounting or a hood in

case of vertical fan mounting.

The outlet spigot must always be connected to the air duct. The fan mounting sequence is shown in Fig. 3-11

OPERATION GUIDELINES

The fan is rated for connection to single-phase AC 120 V/60 Hz power mains.

The fan is rated for continuous operation.

The unit is rated as a class II electric appliance.

Air motion direction in the system must match the pointer on the fan casing.

Ingress protection rating against access to hazardous parts and water ingress — IPX4.

The fan is rated for operation at the ambient air temperature from +34 °F up to +104 °F.

Transported air temperature — from -13 °F up to +140 °F.

Ø D B H L

TT PRO 100 97 195,8 226 302,5

TT PRO 125 123 195,6 226 258,5

TT PRO 150 148 220,1 247 289

CONTROL LOGIC

It is possible to control the fan rotation speed without options by voltage, as well as by thyristor controllers.

The speed controller is purchased separately.

Warning!

When adjusting the voltage, make sure there is no unusual noise or vibration at reduced motor speed.

The motor current may exceed the rated current during voltage regulation.

The fan is equipped with a thermal switch with no self-reset.

To reset the thermal relay, switch oﬀ the power supply.

Find and eliminate the cause of overheating.

Make sure the motor has cooled down to operating temperature.

Switch on the power supply.

TECHNICAL MAINTENANCE

The fan surfaces must be regularly cleaned (once in 6 months) from dirt and dust (Fig. 12-19). Disconnect the

fan from power mains prior to any maintenance operations. To clean the fan, use a soft cloth or a brush wetted

in a mild detergent solution. Do not allow water or liquid come into contact with electric components (Fig. 18).

Wipe the surfaces dry after cleaning.

STORAGE AND TRANSPORTATION REGULATIONS

• Store the unit in the manufacturer’s original packaging box in a dry closed ventilated premise with

temperature range +5...+40 ˚С and relative humidity up to 70 %.

• Storage environment must not contain aggressive vapors and chemical mixtures provoking corrosion,

insulation, and sealing deformation.

• Use suitable hoist machinery for handling and storage operations to prevent possible damage to the unit.

• Follow the handling requirements applicable for the particular type of cargo.

• The unit can be carried in the original packaging by any mode of transport provided proper protection

against precipitation and mechanical damage. The unit must be transported only in the working position.

• Avoid sharp blows, scratches, or rough handling during loading and unloading.

• Prior to the initial power-up after transportation at low temperatures, allow the unit to warm up at operating

temperature for at least 3-4 hours.

TROUBLESHOOTING

Problem Possible reasons Troubleshooting

When the unit is connected to power

mains, the fan does not rotate and

does not respond to any controls.

No power supply.

Make sure the power supply line

is connected correctly, otherwise

troubleshoot the connection error.

Internal connection fault. Contact the Seller.

Low air ﬂow. The ventilation system is clogged. Clean the ventilation system.

Increased noise, vibration.

The impeller is clogged. Clean the impeller.

The fan is not secured well or is not

mounted properly. Troubleshoot the installation error.

The ventilation system is clogged. Clean the ventilation system.

Andere Handbücher für TT PRO Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Vents Lüfter Handbücher

Vents

Vents VKV Series Bedienungsanleitung

Vents

Vents KSB EC Series Bedienungsanleitung

Vents

Vents TwinFresh Comfo RA1-25 Bedienungsanleitung

Vents

Vents TwinFresh Comfo RA-50 Bedienungsanleitung

Vents

Vents VCUN Bedienungsanleitung

Vents

Vents 100 Style Eco Bedienungsanleitung

Vents

Vents VKMz 125 Bedienungsanleitung

Vents

Vents Solo RA1-35A-9 P Bedienungsanleitung

Vents

Vents VV 180 Bedienungsanleitung

Vents

Vents VENTS TT Series Bedienungsanleitung

Vents

Vents TT Silent-M 450-4E Bedienungsanleitung

Vents

Vents VDO Series Bedienungsanleitung

Vents

Vents TwinFresh Comfo RA-50 V.3 Bedienungsanleitung

Vents

Vents RO Series Bedienungsanleitung

Vents

Vents VKV EC Series Bedienungsanleitung

Vents

Vents TwinFresh Comfo SA-50 Bedienungsanleitung

Vents

Vents Boost 315 Bedienungsanleitung

Vents

Vents KSA Series Bedienungsanleitung

Vents

Vents CBF 200 Bedienungsanleitung

Vents

Vents TwinFresh Comfo RA1-50 Bedienungsanleitung

Vents

Vents VN Series Bedienungsanleitung

Vents

Vents VKV Series Bedienungsanleitung

Vents

Vents CBF LP 110 DC Bedienungsanleitung

Vents

Vents TwinFresh Expert Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung