Verkada CD22 Bedienungsanleitung

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

Install Guide

CD22 CD32 CD42 CD52

Indoor Dome Camera

Document

Document Details

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

V1.7 (20230901)

(V1.0 first published 20211208)

Firmware

Firmware version can be verified on

Verkada Command command.verkada.com.

Product Models

This install guide pertains to models CD22-HW,

CD32-HW, CD42-HW, CD52-HW.

Introduction

What’s in the box

What you’ll need

●A working Internet connection

●802.3af Power over Ethernet (PoE)

switch, or a PoE injector. For operation

below -20° C, use 802.3at PoE.

●A smartphone or laptop

●A #2 Phillips screwdriver or power drill

with a #2 Phillips driver bit

●1/4 inch (6.5mm) drill bit for wall

anchors

●1/8 inch (3mm) drill bit for pilot holes

●A Cat5 or Cat6 Ethernet cable with a

0.2-0.25 inch outside diameter

(5-6.5mm)

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

Indoor Camera Mount plate

(Attached to camera)

Mounting template

3 M4 x 50mm machine screws,

wing nuts, and washers

4 Wall anchors T10 Security Torx screwdriver4 M4 x

25mm PH2

wall screws

Connect

For easy registration and setup, scan the QR

code on the product.

If you prefer to manually register your product,

please proceed to: verkada.com/start

Placement

Mount the camera on a wall or ceiling. Try to

keep the camera 8 to 10 feet above the

ground.

For best night vision, avoid overhangs or

obstructions. These may reflect the camera’s

IR illumination and reduce the image clarity in

night mode.

Introduction

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

LED Behaviors

Regular operation

Solid Orange

Camera is on and booting up.

Flashing Orange

Camera is updating firmware.

Solid Blue

Camera is running, connected,

and recording data.

Flashing Blue

Generic network error. Contact support.

Network errors

1 Blue, 1 Orange

Camera is connected with PoE, but

unable to connect to the Switch.

1 Blue, 2 Orange

Camera has not received an IP address.

1 Blue, 3 Orange

Camera is not able reach the

configured Gateway.

1 Blue, 4 Orange

Camera has detected duplicate IP

addresses on the LAN.

The LED will flash in a specific order,

depending on the error state. You will

see 1 blue flash, followed by a number of

orange flashes.

Example of 1 Blue, 5 Orange flash sequence

1 Blue, 5 Orange

Camera is not able to resolve Verkada

hostnames.

1 Blue, 6 Orange

Camera is not able to receive a

response from the NTP Server.

1 Blue, 7 Orange

Camera is not able to certify the SSL

connection, likely due to SSL inspection.

1 Blue, 8 Orange

Verkada endpoints are not reachable

after boot up.

–

Status LED

Installation

Assembly 1/2

Note

Please keep the protective film adhered to the clear

bubble until completing the final step of installation.

Use the provided T10

Security Torx security

screwdriver to loosen the

screws and lift the cover.

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

Connect the camera to

an 802.3af/at Power

over Ethernet port on

your network.

Installation

Assembly 2/2

Note

The status LED will turn orange to indicate the camera has power. The LED

will turn blue to indicate the camera is active. See additional LED states and

definitions under LED Behavior.

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

Gently pull the cable through the

through-hole so it has some

slack, but will not interfere with

the top cover.

Pulling the Ethernet cable too

tight will strain the cable which

may impact data performance.

Too much slack in the Ethernet

cable may create top cover

installation issues.

Installation

Mounting

Note

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

1. Use the provided T10 security torx security screwdriver to

loosen the screws and lift the cover. To remove the

mount plate, loosen the mount plate screws and twist

the camera counter-clockwise. Lift the camera vertically

off the base plate and set aside.

2. Use the provided mounting template to mark wall

mount holes. For a junction box mount, use the

mounting template to determine the correct hole

pattern.

3. For a solid material like wood or metal, drill 1/8 inch pilot

holes. Drive mounting screws directly into the pilot holes.

4. For drywall, drill 1/4 inch holes. Insert plastic anchors into

holes and drive mounting screws into anchors.

5. To secure the camera, place it over the mount plate

screws and twist counter-clockwise. Tighten the mount

plate screws with a Phillips screwdriver.

Installation

Adjust

Note

Adjust your camera to the desired viewing angle. Use the online stream to

confirm image orientation.

Image can be flipped 180˚ online in Command.

Default image orientation is indicated by markings on the lens face. Video

orientation is also adjustable from within the Verkada application.

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

Installation

Secure

Note

After positioning your camera correctly, align the top shell security holes

with the baseplate and place the top shell back into its original position.

Tighten the security screws using the provided T10 security torx screwdriver.

Remove plastic film after top cover is secured.

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

Appendix

CD22 CD32 CD42 CD52 Compliance

Caution 1. Maintenance and repair work must always be carried out by qualified technical personnel.

Disconnect power from the unit when performing a maintenance task.

2. Wiring methods used for the connection of the equipment to earth shall be in accordance with the

National Electrical Code, ANSI/NFPA 70, and the Canadian Electrical Code, Part 1, CSA C22.1.

3. The product must be installed and protected in a location that is not easily accessible and is away

from impacts or heavy vibration.

4. The device is only to be connected to PoE networks without routing to outside plants.

5. If powered by a power adapter, the adapter should be properly grounded.

6. Please contact certified dealers for power adapters.

PoE

Adapter

To reduce potential safety issues, only use the PoE adapter provided with the product, a replacement PoE

adapter provided by Verkada, or a PoE adapter purchased as an accessory from Verkada.

Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401

[email protected]

All specifications are subject to change without notice

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Verkada Sicherheitskamera Handbücher

Verkada

Verkada CM41-E Bedienungsanleitung

Verkada

Verkada CB51 Bedienungsanleitung

Verkada

Verkada CD41 Bedienungsanleitung

Verkada

Verkada CD52 Bedienungsanleitung

Verkada

Verkada D30 Bedienungsanleitung

Verkada

Verkada CD31 Bedienungsanleitung

Verkada

Verkada CD32-E Bedienungsanleitung

Verkada

Verkada CB51 Bedienungsanleitung

Verkada

Verkada D50 Bedienungsanleitung

Verkada

Verkada CB61 Bedienungsanleitung

Verkada

Verkada CB51 Bedienungsanleitung

Verkada

Verkada CD22-E Bedienungsanleitung

Verkada

Verkada CM41-S Bedienungsanleitung

Verkada

Verkada CB52 Bedienungsanleitung

Verkada

Verkada CM41 Bedienungsanleitung

Verkada

Verkada D40 Bedienungsanleitung

Verkada

Verkada D80 Bedienungsanleitung

Verkada

Verkada CD51 Benutzerhandbuch

Verkada

Verkada CD31-E Handbuch

Verkada

Verkada CD62 Bedienungsanleitung

Verkada

Verkada CD32 Bedienungsanleitung

Verkada

Verkada CF81-E Bedienungsanleitung

Verkada

Verkada CM61 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung