Verve EDWS Bedienungsanleitung

Installation Guide

Model: EDWS

Door / Window Sensor

Package Contents

▪Sensor and magnet

▪4 screws

Product Description

For use as both:

▪Entry Door Sensing

▪Outside Door / Window Sensing

The Verve Door/Window Sensor provides energy savings by

detecting when a door or window opens or closes.

It is a wireless solar-powered sensor that can be used on its own

to detect the open and closed status of entry doors or windows,

or it can be linked with occupancy sensors to more accurately

track when a room is occupied or vacant.

The sensor is easy to install on door and window frames, and

virtually anything indoors that opens and closes.

Features Include:

▪Sends wireless message to other devices whenever a door or

window opens or closes

▪Harvests ambient solar energy to power the sensor and send

wireless communication

▪Mounts easily on standard doors or windows

▪Works with motion sensors to track room occupancy

▪Supplemental battery option for extreme low-light condi-

tions

Specications

Power Supply Indoor light energy harvesting

(Optional) Supplemental battery

Transmission Range 80 ft. (25 m)

RF Communications EnOcean 315 MHz , 902 MHz

Charge Time

before Linking

2.7 hours @ 10 lux

3.7 minutes @ 200 lux

Light Required to

Sustain Operation

15 lux for 6 actuations/hour

50 lux for 30 actuations/hour

100 lux for 60 actuations/hour

Charge Time for

Full Charge

21 hours @ 200 lux (after startup)

42 hours @ 200 lux (cold start)

Operating Life in Dark-

ness (after full charge)

174 hours: heartbeat only

67 hours @ 10 actuations/hour

10 hours @ 100 actuations/hour

EEP (EnOcean

Equipment Prole)

D5-00-01

Maximum Sensor Gap 0.25 inch (6.4 mm)

Dimensions (Sensor) 3.15” L x 0.83” W x 0.59” D

(80 mm x 21 mm x 15 mm)

Dimensions (Magnet) 3.15” L x 0.47” W x 0.5” D

(80 mm x 12 mm x 13 mm)

Weight (Total) 0.97 oz. (27.5 g)

Environment • Indoor use only

• 32° to 131° F (0° to 55° C)

• 5% to 95% relative humidity

(non-condensing)

Agency Compliance FCC, IC

Planning

Take a moment to plan for the sensor’s successful operation and

optimal communication with other system components.

Remove the sensor from its packaging and place it under a

strong light to charge it for installation.

▪Ensure the location provides consistent and adequate light

▪Install according to the alignment requirements

▪Determine which sensor prole is appropriate (when linking

with EnOcean-based In-line Switch, Plug-in Switch or HVAC

Setback Modules (refer to the “Linking” and “Sensor Proles”

sections) - otherwise; when linking with 3rd party control-

lers, these proles aren’t relevant

Consider the construction materials, such as metal and concrete,

in the space and obstacles that may interfere with RF signals

Tools Required

▪Screwdriver

▪Leveling tool

▪Light meter

0.83”

21mm

0.47”

12mm

0.59”

15mm

3.15”

80mm

0.5”

12.7mm

Solar P

anel

Link Button

Alignment Ar

row

(Sensor)

Alignment Arrow

(Magnet)

LED Display

Alignment Requirements

The proximity of the magnet to the sensor is important for

proper detection. The alignment arrows on the sensor and the

magnet must point to each other and the gap between them

must not exceed .25 inch (6.4mm) in any direction.

Alignment Guidelines

gap is 1/4” (6.4mm)

or less

misaligned

arrows

gap is too wide

Front View End View

Installing

1. Based on your requirements, decide where you want to in-

stall the sensor and the magnet. For door installations, locate

the sensor:

• On the knob side of the door jamb, away from hinges.

• At least 1 ft. (30 cm) above the oor to avoid damage.

For window installations, make sure the location does not

expose the sensor to contact with water.

2. Follow the alignment requirements that are described in the

Planning section.

NOTE: For easy access and handling, it is recommends that

the sensor be linked to a transceiver before installing it, see

the Linking section.

3. Install the sensor on the interior side of the xed frame.

A. Remove the mounting

bracket from the sensor.

estimated time: 20 minutes

Tab lock

Notch

Tab lock

Notch

B. Position the mounting bracket and mark the two mount-

ing screw drill points.

C. Insert the rst screw loosely and level the mounting

bracket.

NotchesNotches

D. Install the second screw, and then hand-tighten the rst

screw.

E. Snap the sensor onto the mounting bracket where the

notches are located.

Tab lockTab lock

F. Slide the sensor on the bracket until it snaps into place

on the tab lock.

4. Install the magnet on the moving part of the door or win-

dow.

A. Use a screwdriver to press the tab lock and ex the mag-

net cover to remove it.

Tab lockTab lock

The cover is removed from the magnet body.

Door/Window Sensor • Installation Guide

The two mounting

holes are exposed.

B. Position the magnet with the proper spacing and align-

ment, and then install it with the provided screws.

C. Replace the magnet cover and snap it into place on the

tab lock.

NOTE: For low activity applications, the magnet can be

mounted with double-sided tape (not included).

5. Check the alignment arrows and the distance between the

sensor and magnet when the door or window is closed.

TIP: There is a faintly audible click when the sensor and mag-

net close and open.

Linking

Two or more EnOcean-based devices can be linked and cong-

ured to provide the desired control. There are two basic types of

devices in the system; transmitters and transceivers.

▪Transmit-only: Transmitters are simple energy-harvesting

devices that send RF messages to communicate a condition,

level, or state. Transmitters can only be linked to transceivers.

Examples > Self-powered Light Switches, Occupancy Sensors

▪Transmit & Receive: Transceivers are controlling devices

that send as well as receive RF messages. They also process

relevant control logic, and actuate the appropriate outputs

(switching a light on or off for example). Transceivers can be

linked with transmitters as well as other transceivers. A trans-

ceiver can have up to 30 devices linked to it.

Examples > Relays, Gateways

Cover

Mounting Holes

Cover

Mounting Holes

Fixed Frame

Moving Part

Fixed Frame

Moving Part

The Door/Window Sensor is a Transmit-only Device.

To link the Door/Window Sensor to a transceiver; the transceiver

must rst be powered, within wireless range, and set to accepts

links.

Next, the desired transmitter, or another transceiver, is triggered

to send a special link message. The awaiting transceiver receives

and stores the link permanently so the devices can interact to

provide a variety of intelligent control options.

Sensor Proles

The sensor prole determines how the sensor is used within the

system, whether it is for occupancy detection, HVAC control, or

single load control. How the sensor interacts with other devices

depends on where it is installed and how it is linked. There are

three sensor proles.

NOTE: These proles are supported for linking with EnOcean

EISM (In-line Switch), EPSM (Plug-in Switch), and EHSM (HVAC

Setback) controllers. Consult the manual for the respective con-

trollers to determine the capabilities of the solution.

Entry Door - for Occupancy Detection

For this prole, the sensor is installed on an entry door and

operates with a motion sensor as follows:

Door Opens Door Closes

The door/window ajar

timer starts. If the timer

runs out, shutdown mode

is activated on the HVAC

system.

The door/window ajar timer

is reset if all monitored doors

and windows are closed. The

vacancy check timer starts,

if the motion sensor detects

occupancy, normal mode is

activated on the HVAC system.

Window or Patio Door for HVAC Control

For this prole, the sensor is installed on a window or patio door

and operates as follows:

Window Opens Window Closes

The door/window ajar

timer starts. If the timer

runs out, shutdown mode

is activated on the HVAC

system.

The door/window ajar timer

is reset if all monitored doors

and windows are closed.

Normal mode is activated on

the HVAC system.

Closet Door for Single Load Control

For this prole, the sensor is installed on a closet door and oper-

ate as follows because it is the only linked device:

Door Opens Door Closes

The switched auto-off timer

starts and the light turns

on. If the timer runs out the

light turns off.

The light turns off.

Door/Window Sensor • Installation Guide

Verve Living Systems is a registered brand of

ZENO Controls, LLC p4

support@vervelivingsystems.com

(877) 874-8774

To Link or Unlink a Sensor

When a Door/Window Sensor is linked, the position of the

magnet indicates to the transceiver which type of sensor prole

is being used.

1. Set the desired transceiver to Accept a Link.

2. Do one of the following according to the desired prole:

A. Entry door for occupancy detection, place the magnet

beside the sensor (closed position).

B. Window or patio door for HVAC control, move the mag-

net way from the sensor (open position).

C. Closet door for single load control, move the magnet

away from the sensor (open position).

3. Press the Link button on the sensor once.

The Set button on the transceiver

will be solid green for 3 seconds.

The device is now linked.

Installing Supplemental Battery (optional)

If the sensor is installed where the light levels are consistently

too low or there are days of darkness, battery power can be

used to supplement the solar energy harvester. Only use a

CR1216 battery.

1. Press the tab lock to release the

sensor from the mounting bracket.

2. Slide the sensor about ½” (1 cm)

and remove it from the mounting

plate.

3. Insert the battery with the positive

pole (+) up and slide it between

the two contact terminals with

your nger.

WARNING: Ensure the battery is properly oriented. Improper

handling of lithium batteries may result in heat generation,

explosion, or re.

4. Replace the sensor on the mount-

ing plate and slide it until it snaps

into place.

5. Open and close the contact to test

for power.

6. There should be a faintly audible

click and a fast LED blink.

Tab lock

Notch

Tab lock

Notch

Contact Te rminalsContact Te rminals

Troubleshooting

Problem Solution Checklist

The sensor does not

generate a wireless

message

▪Verify there is a faintly audible click when the

contact is closed and opened

▪Verify the LED blinks once when the contact is

closed and opened

▪Verify the solar cell is charged properly

▪Check that the magnet is oriented to the sen-

sor properly

▪Check that the alignment arrows are not

spaced more than .25 inch (6.4 mm)

The linked device

does not respond

to wireless mes-

sages

▪Check for environment or range issues. Tip:

Reorienting the sensor may overcome adverse

RF conditions

▪Verify the device is linked

▪Check the transceiver connection and the wir-

ing for errors

▪Check if appropriate devices are linked accord-

ing to good system planning

902 MHz: Contains: 315 MHz: Contains:

FCC: SZV-STM311U FCC: SZV-STM311C

IC: 5713A-STM311U IC: 5713A-STM311C

This device complies with part 15 of the FCC rules and Industry Canada ICES-003. Operation is subject

to the following two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired operation.

IMPORTANT! Any changes or modications not expressly approved by the party responsible for

compliance could void the user’s authority to operate this equipment.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts

de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire

de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, meme

si le brouillage est susceptible d’en compromettre le fonctionnement.

IMPORTANT! Tous les changements ou modications pas expressément approuvés par la partie

responsable de la conformité ont pu vider l’autorité de l’utilisateur pour actioner cet équipment.

Door/Window Sensor • Installation Guide

Inhaltsverzeichnis

Andere Verve Zubehör Handbücher

Verve

Verve VOSC Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung