Vestfrost FZ 316 Bedienungsanleitung

FZ 316 / 354 / 310 / 272 / 307 / 253 / 286 M

Instruction for use

Thank you for purchasing your new fridge/

freezer from Vestfrost. Please note that

these instructions apply to all fridge/freezers

in the FZ range. Illustrations and ﬁttings

may therefore not necessarily correspond

exactly to your model.

Warning

As the refrigerant used in this appliance is a

ﬂammable gas (Isobutane R600a), special

care must be taken to prevent damage

to the refrigerant circuit and piping during

transport and installation.

If damage does occur, avoid sparks or

naked ﬂame in the vicinity of the appliance,

ensure that the room is well ventilated,

disconnect the power supply, and contact

your supplier.

The unit must only be serviced by qualiﬁed

technicians from an approved service

centre.

Old appliances

Old refrigerators and freezers are often

ﬁtted with complicated latches that can

only be opened from the outside. If you

have one of these old units stored away

somewhere, or if you scrap one, remember

to destroy the latch ﬁrst in order to prevent

children from being exposed to danger by

getting locked inside the unit.

Disposal

This appliance contains recyclable

materials. Before disposing of the unit,

detach the plug from the cable and remove

the doors. If the doors are left on, the

appliance is highly dangerous for children

at play.

Environmental regulations on disposal must

also be observed. When disposing of the

appliance you should contact your local

authority technical department who will

inform you of how collection and recycling

of such units take place in your area.

Before use

Before operating your new appliance,

please read the following instructions

carefully as they contain important

information on safe installation, operation

and maintenance. Keep the instructions for

future reference.

On receipt, check to ensure that the

appliance has not been damaged during

transport. Transport damage should be

reported to the local distributor before the

appliance is put to use.

Remove the packaging. Clean the inside of

the cabinet using warm water with a mild

detergent. Rinse with clean water and dry

thoroughly (see cleaning instructions). Use

a soft cloth.

If during transport the appliance has been

laid down, or if it has been stored in cold

surroundings (colder than +5°C), it must be

allowed to stabilise in an upright position for

at least an hour before being switched on.

Contents

Get to know your fridge/freezer.........3

Installation and start-up.....................4

Electrical connection.........................6

Reversing the doors..........................7

Operation and function......................8

Refrigerator section.........................11

Freezer section...............................12

Cleaning and maintenance.............14

Fault ﬁnding....................................15

Warranty, spare parts and service..16

Get to know your fridge/freezer

ﬁg. 1

Control panel

Lighting

Shelf with storage boxes

Door shelf

Bottle rack

Large storage box

Glass shelf

Nameplate

Crisper bins

Freezing tray

Sealing strip

Freezer drawers

Door handle

Defrost water drain

Kick plate

Adjustable feet

Placement

For safety and operational reasons, the

appliance must not be installed outdoors.

The appliance should be placed on a level

surface in a dry, well ventilated room (max.

75% relative air humidity). Never place the

appliance close to sources of heat such as

cookers or radiators, and avoid placing it in

direct sunlight.

Room temperature

The climate class is stated on the

nameplate (see ﬁg. 1 on page 3 and ﬁg. 17

on page 13). This speciﬁes the optimum

room temperature.

Climate class Optimum room

temperature

SN +10 ºC to +32 ºC

N +16 ºC to +32 ºC

ST +18 ºC to +38 ºC

T +18 ºC to +43 ºC

Installation

The surface on which the appliance is to be

placed must be level. Do not use a frame or

similar.

The appliance can be installed as a free-

standing unit against a wall, built into a

kitchen element, or lined up with other

appliances (ﬁgs 2 and 3).

600

ﬁg. 2

ﬁ g . 3

Installation and start-up

Ventilation

It is important that the appliance be

well ventilated and that air can circulate

unhindered above, below and around it. The

ﬁgures below illustrate how the necessary

air circulation can be ensured (ﬁgs 6 and

7). If two fridge/freezers are placed side

by side, there must be at least 30 mm

clearance between them.

1650/1950

100

1560/1860

ﬁg. 6 ﬁg. 7

The appliance

viewed from above

If the appliance is placed beside a wall,

there must be sufﬁcient room for the freezer

door to be opened wide enough to allow the

drawers to be pulled out (ﬁg. 4).

600

610 ﬁ g . 4

Fitting the tilt-stop

A tilt-stop can be ﬁtted to prevent the

unit from tilting forwards when the door

is opened. Mount the tilt-stop on the wall

behind the appliance 80-100 mm from the

left or right side of the appliance depending

on the side on which the door is hinged.

The tilt-stop must always be ﬁtted on the

side opposite to the hinge (ﬁg. 5).

80 - 100 mm

ﬁg. 5

Setting up

It is important that the appliance be

absolutely level. To level the appliance,

remove the kick plate below the door and

screw the adjustable feet up or down (ﬁgs

8 and 9). Use a spirit level to check that the

appliance is absolutely level.

If the appliance is to be placed on a soft

surface, e.g. ﬂoorboards or a carpet, it is

best to recheck whether the appliance is still

level after a period of time as the underlying

surface may give under the weight of the

appliance.

ﬁg. 8

ﬁg. 9

Reversing the doors

The doors can be changed from right-hinged to left-hinged and vice versa as follows:

1. Lay the appliance on its back with the

doors uppermost.

8. Opposite the hinge, there are two

screws covered by plastic caps.

Remove the caps and screws.

13. Reﬁt the kick plate

14. Adjust the lower hinge and tighten.

2. Remove the upper hinge.

3. Move the plastic plugs to where the

upper hinge was ﬁtted.

4. Lift off the upper door and lay it aside.

9. Turn the central bridging plate and insert

the pins into the slots on the opposite side.

10. Reﬁt the screws and plastic caps.

15. Fit the lower door and attach the

middle hinge.

16. Adjust the hinge and tighten.

5. Remove the door-closer and reﬁt it on

the opposite side.

11. Remove the kick plate by pulling it

outwards and upwards.

17. Fit the upper door.

18. Keep the door-closer to the left.

19. Fit the upper hinge.

6. Remove the middle hinge by unscrewing

the screws.

7. Lift off the lower door and lay it aside.

12. Remove the screws holding the lower

hinge in place. Turn the pin on which

the door was mounted so that it points

in the opposite direction. Rotate the

hinge through 180° and reﬁt it on the

opposite side of the appliance.

20. Remove the door handles and reﬁt

them on the opposite side. Reﬁt the caps.

21. The appliance must be allowed to

stabilise in an upright position for at least

1.5 hours before being switched on.

22. After reversing the door(s), it is important to check that the sealing strip provides a tight seal all the way round.

If it does not, carefully heat the strip all the way round using a hair dryer. Then ease the strip outwards slightly so that it forms a tight

seal against the cabinet.

Be careful not to heat the strip so much that it melts!

The appliance is intended for connection

to alternating current. The required voltage

(V) and frequency (Hz) are stated on the

nameplate inside the appliance. Power

must be connected via an independent wall

socket outlet.

If the mains lead has been damaged, it

must be replaced with a corresponding

type supplied by the manufacturer or an

approved service centre.

Technical data

This appliance complies with CE marking

regulations, directives and standards.

Low Voltage Directive 73/23/EEC.

EMC Directive 89/336/EEC.

Council Directive 92/75/EEC on the energy

labelling of household appliances as

subsequently amended by 94/2/EC and

2003/66/EC.

Directive 96/57/EC on energy efﬁciency

requirements, and subsequent

amendments.

Electrical connection

Electronic controls

The appliance is factory set to maintain

+5°C in the refrigerator section and -18°C

in the freezer section. Following any power

failure, these settings are automatically

recalled.

After switching the appliance on, it takes a

few hours before the correct temperatures

are achieved. During this period, the control

lamp ﬂashes red and the acoustic alarm is

heard. It is therefore a good idea to switch

off the sound. To do so, press the alarm

button .

The electronic controls have the following

functions:

• On/off function

• Temperature setting

• Temperature display

• Automatic defrosting of refrigerator

section

• Automatic defrosting of freezer

section (frost-free models only)

• Super Freeze

• Acoustic and visual alarms

• Fault-ﬁnding, emergency and

service programs

On/off switch

Button for displaying and setting

refrigerator temperature

Button for displaying and setting

freezer temperature

Display showing temperature

Button for switching off the alarm

Super Freeze button

Control lamp

Four-star freezer symbol

Freezer temperature

Refrigerator temperature

Alarm on/off

Super Freeze

On/off switch

Concealed door switch

Display

Operation and function

ﬁg. 12

Starting up

Connect the appliance to the socket outlet.

Press the on/off switch .

The actual temperature in the freezer

section is shown on the display.

To display the actual temperature in the

refrigerator section, press the refrigerator

button once. After 1 minute, the display

returns automatically to the temperature

in the freezer section. Alternatively, press

the freezer button once to return to the

temperature in the freezer section.

Temperature setting

The temperature in the refrigerator section

can be set from +2°C to +9°C by pressing

the refrigerator button . The display

shows the temperature setting. Press the

button until the desired temperature setting

is displayed.

The temperature in the freezer section can

be set from -24°C to -16°C by pressing

the freezer button . The display shows

the temperature setting. Press the button

until the desired temperature setting is

displayed.

Note that the temperature in the freezer

section should be -18°C or lower in order to

prevent microorganisms from multiplying.

A temperature setting of 4°C is

recommended for the refrigerator section.

Super Freeze

Before freezing large quantities of fresh

food, it is recommended that the Super

Freeze function be activated.

To do so, press the Super Freeze button .

The control lamp lights yellow to indicate

that the Super Freeze function is switched

on.

Super Freeze is used to freeze large

quantities of fresh items and must be

activated up to 24 hours before placing

such items in the freezer.

When Super Freeze is switched on, the

compressor runs constantly and the

temperature in the freezer falls below the

normal setting. This temperature reduction

ensures that non-frozen items do not affect

the temperature and thus the quality of

frozen items already stored in the freezer.

Super Freeze is switched off automatically

after 24 hours.

Door-open alarm

If the door has been left open for longer

than two minutes, an acoustic alarm is

activated and the control lamp ﬂashes red.

Both these alarms are reset when the door

is closed. On pressing the alarm button ,

only the acoustic alarm is switched off.

High-temperature alarm

Visual and acoustic alarms are activated if

the freezer temperature has been higher

than -10°C for more than 90 minutes. If

the temperature drops again, the visual

and acoustic alarms remain active and

the display continues to show the highest

temperature recorded in the freezer. To

reset the alarms, press the alarm button .

This switches off the alarms and returns

the display to the actual temperature in the

freezer.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Vestfrost Kühlschrank Handbücher

Vestfrost

Vestfrost CX 232 W Bedienungsanleitung

Vestfrost

Vestfrost VICF 105177 S Bedienungsanleitung

Vestfrost

Vestfrost VC 10146 Bedienungsanleitung

Vestfrost

Vestfrost CNF 289 XB Bedienungsanleitung

Vestfrost

Vestfrost R-90i Bedienungsanleitung

Vestfrost

Vestfrost VR-FW916-1E0I Bedienungsanleitung

Vestfrost

Vestfrost VF566MSLV Bedienungsanleitung

Vestfrost

Vestfrost CVKS 611-670-671 Bedienungsanleitung

Vestfrost

Vestfrost SW Series Bedienungsanleitung

Vestfrost

Vestfrost VR-BB27612H1S Bedienungsanleitung

Vestfrost

Vestfrost VF 473 EW Bedienungsanleitung

Vestfrost

Vestfrost AKG 377 Bedienungsanleitung

Vestfrost

Vestfrost CLF384 EW Bedienungsanleitung

Vestfrost

Vestfrost FW M Series Bedienungsanleitung

Vestfrost

Vestfrost R-138 Bedienungsanleitung

Vestfrost

Vestfrost CW 397 R Bedienungsanleitung

Vestfrost

Vestfrost CFKS 471 Bedienungsanleitung

Vestfrost

Vestfrost BBR150 Bedienungsanleitung

Vestfrost

Vestfrost WAI 73664-2 M NF Bedienungsanleitung

Vestfrost

Vestfrost HOF KF 186 Bedienungsanleitung

Vestfrost

Vestfrost VLS 204A Bedienungsanleitung

Vestfrost

Vestfrost VR-FB373-2E0BG Bedienungsanleitung

Vestfrost

Vestfrost VF 473 EBH Bedienungsanleitung

Vestfrost

Vestfrost MK 304 Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung