Viavi OneAdvisor 800 400G Module Bedienungsanleitung

VIAVI//Public

OneAdvisor High-Speed Network Testing Platforms

QUICK CARD

https://www.viavisolutions.com/en-us/product-family/oneadvisor

Ethernet Y.1564 Layer 2 Traffic

This quick card describes how to set up the OneAdvisor 800 400G Module or OneAdvisor 1000 400G

Module to run an ITU Y.1564 Layer 2 Traffic Test for Metro Ethernet service activation.

LAUNCH TEST

1. Press the Power button to turn on the

OneAdvisor.

2. Press the 400G Module icon

at the top of the screen.

3. Using the Select Test menu, Quick Launch

menu, or Job Manager, launch the Ethernet

Layer 2 Traffic test for the desired data rate on

the desired port (P1 or P2). For example:

Ethernet ►400GigE Optical

►Y.1564 SAMComplete ►Layer 2 Traffic

►P2 Terminate.

4. Tap the button next to “Start a New

Configuration (reset to defaults)”

Figure 2: Launch Test

Figure 3: Start a New Configuration

Figure 1: Equipment Requirements

•OneAdvisor 800 or OneAdvisor 1000 equipped with the following:

o400G Transport Module

oTransport software release V4.0.0 or greater

oSoftware option for data rate to be tested:

✓CA10M1GE test option for 10/100/1000M

Copper or 1 Gigabit Optical Ethernet

✓CA10GELAN test option for 10 Gigabit Ethernet

✓CA25GE test option for 25 Gigabit Ethernet

✓CA40GE test option for 40 Gigabit Ethernet

✓CA50GE test option for 50 Gigabit Ethernet

✓CA100GE test option for 100 Gigabit Ethernet

✓CA200GE test option for 200 Gigabit Ethernet

✓CA400GE test option for 400 Gigabit Ethernet

•Optical Transceiver supporting the Ethernet data rate

to be tested (SFP, QSFP, or OSFP)

•Cables to match the optical transceiver and the line under test

•Fiber optic inspection microscope (P5000i or FiberChek Probe)

•Fiber optic cleaning supplies

VIAVI//Public

OneAdvisor High-Speed Network Testing Platforms

QUICK CARD

►The following Information is needed to

configure the test:

•Frame Size

•VLAN ID, if VLAN tagging is used.

•Committed Information Rate (CIR)

•Pass/Fail Threshold for Frame Loss

Ratio, Delay, and Delay Variation (Jitter)

1. Tap the button to display the

Local Network Settings 1 screen.

►Select the Frame Size you wish to

generate.

2. Tap to display the

Local Network Settings 2 screen.

►If you are testing a VLAN, set

Encapsulation to VLAN and enter

the VLAN ID.

CONFIGURE TEST

Figure 4: Work Order

Figure 6: Local Network Settings 2

Figure 5: Local Network Settings 1

VIAVI//Public

OneAdvisor High-Speed Network Testing Platforms

QUICK CARD

4. Tap to display the SLA Throughput

screen.

►Enter the Committed Information Rate

(CIR).

►If the you are testing at full line rate or if

traffic is not being policed, uncheck the

Policing checkbox.

5. Tap the button twice to display the

SLA Performance screen.

►Enter the Frame Loss Ratio, Frame Delay,

and Delay Variation pass/fail criteria.

6. Tap the button 5 times to display the

J-QuickCheck screen. Figure 8: SLA Performance

Figure 9: J-QuickCheck

Figure 7: SLA Throughput

VIAVI//Public

OneAdvisor High-Speed Network Testing Platforms

QUICK CARD

►For Optical Interfaces:

1. Use the VIAVI P5000i or FiberChek Probe

microscope to inspect both sides of every

connection being used (SFP, attenuators,

patch cables, bulkheads)

oFocus the fiber on the screen.

oIf it appears dirty, clean the fiber end-face

and re-inspect.

oIf it appears clean, run the inspection test.

oIf it fails, clean the fiber and re-run

inspection test. Repeat until it passes.

2. Insert desired Optical Transceiver into the

Port 1 SFP or QSFP slot on the top of the

OneAdvisor.

3. If necessary, insert optical attenuators into

the SFP/QSFP TX and/or RX ports.

4. Connect the SFP/QSFP to the port under

test using a jumper cable compatible with

the line under test.

►For Copper 10/100/1000BASE-T interfaces:

1. Insert Copper SFP into the Port 1 SFP or

slot on the top of the OneAdvisor.

2. Connect the copper SFP to

the port under test using CAT 5E or better

cable.

►Verify that Local Port status UP and Full

Duplex (FD)

►Tap the button.

►Verify that the Remote Loop is recognized.

►Tap the button to display the

Run Y.1564 Tests screen.

Figure 11: Local Port status

Figure 10: Inspect Before You Connect

CONNECT TO LINE UNDER TEST AND LOOP BACK DEVICE

Figure 12: Run J-QuickCheck

VIAVI//Public

OneAdvisor High-Speed Network Testing Platforms

QUICK CARD

Product specifications and descriptions in this

document are subject to change without notice.

Patented as described at viavisolutions.com/patents

To reach the VIAVI office nearest you,

visit viavisolutions.com/contact

+1 844 GO VIAVI

(+1 844 468-4284)

1. Tap the button three times to

display the Report screen.

2. Tap .

3. Tap buttons three times to

close the report and exit the Y.1564 test.

RUN TEST

1. Tap the button.

2. Wait for the test to complete and verify that

all tests pass or complete as indicated by a

green or blue checkmark.

CREATE REPORT

Figure 13: Run Y.1564 Tests

Figure 14: Create Report

Figure 15: Exit

Dieses Handbuch passt für folgende Modelle

Andere Viavi Prüfgeräte Handbücher

Viavi

Viavi ATC-5000NG Bedienungsanleitung

Viavi

Viavi NSC-100 Bedienungsanleitung

Viavi

Viavi AVX-10K Bedienungsanleitung

Viavi

Viavi T-BERD MTS 5800 Stücklistenhandbuch

Viavi

Viavi CT-X Bedienungsanleitung

Viavi

Viavi HST-3000 Stücklistenhandbuch

Viavi

Viavi IFR 6000 Bedienungsanleitung

Viavi

Viavi T-BERD/MTS 5800 Bedienungsanleitung

Viavi

Viavi IFR 6000 Bedienungsanleitung

Viavi

Viavi SmartClass Fiber OLS-85 Bedienungsanleitung

Viavi

Viavi T-BERD/MTS 4000 V2 Stücklistenhandbuch

Viavi

Viavi ONX 580 Bedienungsanleitung

Viavi

Viavi T-BERD MTS 5800 Bedienungsanleitung

Viavi

Viavi IFR 4000 Bedienungsanleitung

Viavi

Viavi FIT-82P03-PRO Bedienungsanleitung

Viavi

Viavi T-BERD/MTS-2000 Stücklistenhandbuch

Viavi

Viavi Certifier Series Bedienungsanleitung

Viavi

Viavi ALT-9000 Bedienungsanleitung

Viavi

Viavi OneAdvisor 1000 Bedienungsanleitung

Viavi

Viavi 7200 Series Bedienungsanleitung

Viavi

Viavi SmartClass Fiber OLTS-85 Bedienungsanleitung

Viavi

Viavi SmartOTDR Stücklistenhandbuch

Viavi

Viavi T-BERD MTS 5800 Stücklistenhandbuch

Viavi

Viavi 8000 V2 Platform Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung