Vicon SurveyorVFT SVFT-UPM-1 Bedienungsanleitung

XX138-10-01

MODEL SVFT-UPM-1 OUTDOOR

PARAPET MOUNT FOR SURVEYORVFT

CAMERA DOME SYSTEMS

Product specifications subject to change without notice.

Vicon and its logo are registered trademarks of Vicon Industries Inc.

Surveyor is a trademark of Vicon Industries Inc.

Teflon is a registered trademark of E.I. duPont de Nemours & Co.

Molykote is a registered trademark of Dow Corning.

VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788

TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116

24-Hour Technical Support: 800-34-VICON (800-348-4266)

UK: +44 (0) 1489-566300 WEB: www.vicon-cctv.com

Vicon part number 8009-8138-10-01 Section 3 Rev 1005

Introduction

The information in this manual covers the installation, operation, and maintenance of the SVFT-UPM-1

Parapet Mount. This unit should only be installed by a qualified technician using approved materials in

accordance with national, state, and local codes. Read these instructions through completely before

attempting installation.

The SVFT-UPM-1 is designed to allow the SurveyorVFT Camera Dome System to be mounted over a roof

parapet or similar structure. The parapet mount provides a sturdy installation capable of withstanding extreme

weather conditions. It allows the mounted equipment to be swiveled onto the roof for easy serviceability and

adjustment.

Installation

Installing the Mounts

The SVFT-UPM-1 Parapet Mount consists of the parapet mount neck, two wall bracket assemblies, a support

bracket, a cap, pipe sealant, and appropriate hardware. See Table 1. The hardware used to secure the

brackets to the mounting surface must be supplied by the customer and appropriate for the type of mounting

surface.

XX138-10-01 Rev 1005 SVFT-UPM-1 Parapet Mount Introduction •1

TABLE 1

MOUNTING KIT COMPONENTS

Item No. Component Quantity Function

1 Wall bracket 2 Secures parapet

mount to mounting

surface

2 Wall bracket cover 2 Secures parapet

mount in wall

bracket

3 Support bracket 1 Secures bottom wall

bracket

4 Cap 1 Closes off bottom of

mount but allows

cabling to be routed

5 5/16-18x1 in. screw 4 Secures wall bracket

cover

6 5/16 lock washer 5 Secures item 5 and

7 5/16x5/8x0.062 flat

washer

5 Secures item 5 and

8 5/16-18x3 in. bolt 1 Prevents parapet

mount from spinning

9 5/16-18 nut 1 Secures item 8

10 Pipe Sealant 1 Seals pipe thread

11 10-32 Nylon Tip Set

screw

1 Secures Dome,

optional

Note: The SVFT-UPM-1 is designed to support the weight of the SurveyorVFT Camera Dome. Refer to the

appropriate product specifications for the weights of these dome systems. Be sure that the mount is

installed in a location that can support the load. There should be a minimum parapet height of 18

inches (46 cm).

Note: For outdoor installations, it is recommended that stainless steel hardware be used. All mounting

hardware MUST have minimum pullout strength of 600 lb (272 kg) per bolt. When mounting to wood,

use screws long enough to penetrate at least 2.5 inches (6.4 cm). If mounting to a steel structure, drill

holes according to the mounting pattern. Screws should be long enough to accommodate lock washers

and nuts. In masonry or concrete, use lead anchors or expansion bolts installed according to the

manufacturer’s instructions.

Caution: Never mount the brackets directly into the end grain of wood.

2 •Installation XX138-10-01 Rev 1005 SVFT-UPM-1 Parapet Mount

Before beginning installation of the parapet mount, run all necessary cabling to the location selected for the

installation. Cables are routed up through the mount to the dome system.

1. Attach one wall bracket and the support bracket to the parapet surface using appropriate hardware for

the material of the parapet. Be sure that the wall bracket is against the parapet surface and the support

bracket is on top of the wall bracket, with the stop on the support bracket facing out from the parapet.

Refer to Figure 1.

2. Attach the second wall bracket to the parapet in the selected location, using appropriate hardware. The

suggested minimum distance between the wall brackets is 12.0 inches (30.5 cm).

3. Insert the cap supplied into the bottom opening of the parapet mount.

4. Place the parapet mount in the cutout contour of the wall brackets, align the wall bracket covers and

secure with the 5/16-18 x 1 inch screws, lock washers and flat washers supplied. To prevent the parapet

mount from spinning, secure it to the bottom wall bracket through the hole in the mount with the 5/16-

18x3 inch bolt, lock washer, flat washer, and nut provided.

5. Route the cables through the cap and up the mount to where the dome system is installed. Apply caulk or

RTV sealant around entrance opening in cap.

6. Install the SurveyorVFT housing. Screw the housing directly onto the parapet mount. Use the pipe

sealant to secure the fit and make it watertight. Refer to the instruction manual for installation of the

domed housing for specific installation instructions.

7. To swivel the dome system out over the parapet, loosen the bolts just enough to allow movement and

position the unit. Tighten the bolts to secure the mount into position.

8. For high vandalism areas, lock the Dome with the soft tip set screw supplied.

Note: If the optional 5/16-18 x 3 inch bolt was installed, it must be removed to swivel the unit.

XX138-10-01 Rev 1005 SVFT-UPM-1 Parapet Mount Installation •3

Figure 1

SVFT-UPM-1 Installation

4 •Installation XX138-10-01 Rev 1005 SVFT-UPM-1 Parapet Mount

Operation

To swivel the mount in from the parapet for access to the dome system, loosen the bolts enough to allow

movement. Swing the unit in from the parapet. Tighten the bolts. After servicing or adjustment is complete,

loosen the bolts, position the mount, and tighten bolts.

Maintenance

The SVFT-UPM-1 Parapet Mount requires no maintenance.

XX138-10-01 Rev 1005 SVFT-UPM-1 Parapet Mount Operation •5

Shipping Instructions

Use the following procedure when returning a unit to the factory:

1. Call or write Vicon for a Return Authorization (R.A.) at one of the locations listed below. Record the name

of the Vicon employee who issued the R.A.

Vicon Industries Inc.

89 Arkay Drive

Hauppauge, NY 11788

Phone: 631-952-CCTV (2288); Toll-Free: 1-800-645-9116; Fax: 631-951-CCTV (2288)

For service or returns from countries in Europe, contact:

Vicon Industries (U.K.) Ltd

Brunel Way

Fareham, PO15 5TX

United Kingdom

Phone: +44 (0)1489/566300; Fax: +44 (0)1489/566322

2. Attach a sheet of paper to the unit with the following information:

a. Name and address of the company returning the unit

b. Name of the Vicon employee who issued the R.A.

c. R. A. number

d. Brief description of the installation

e. Complete description of the problem and circumstances under which it occurs

f. Unit’s original date of purchase, if still under warranty

3. Pack the unit carefully. Use the original shipping carton or its equivalent for maximum protection.

4. Mark the R.A. number on the outside of the carton on the shipping label.

6 •Shipping Instructions XX138-10-01 Rev 1005 SVFT-UPM-1 Parapet Mount

Inhaltsverzeichnis

Andere Vicon Sicherheitskamera Handbücher

Vicon

Vicon Roughneck Pro V2000B Series Bedienungsanleitung

Vicon

Vicon V15CCM-IR-2 Series Rouchneck Bedienungsanleitung

Vicon

Vicon Surveyor 99 Betriebsanleitung

Vicon

Vicon ROUGHNECK V910 Bedienungsanleitung

Vicon

Vicon V960D-N312M Gebrauchsanweisung

Vicon

Vicon Roughneck AI V2000 Series Bedienungsanleitung

Vicon

Vicon IX 8000 IR Bedienungsanleitung

Vicon

Vicon V900-358-24C Bedienungsanleitung

Vicon

Vicon SN680D-A-WNIR Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Vicon

Vicon VC5050-DSP Bedienungsanleitung

Vicon

Vicon XX258-50-01 Roughneck Series Bedienungsanleitung

Vicon

Vicon V662-D-2 Betriebsanleitung

Vicon

Vicon Surveyor MKII Series XX282-20-00 Bedienungsanleitung

Vicon

Vicon V9360W Bedienungsanleitung

Vicon

Vicon XX235-01-01 Betriebsanleitung

Vicon

Vicon VC-700W Bedienungsanleitung

Vicon

Vicon V942D-W312MIR Bedienungsanleitung

Vicon

Vicon V920B-A Series Bedienungsanleitung

Vicon

Vicon V-CELL-HD Bedienungsanleitung

Vicon

Vicon V661D-312IR Betriebsanleitung

Vicon

Vicon SN240D Bedienungsanleitung

Vicon

Vicon Roughneck Pro V2000D Series Bedienungsanleitung

Vicon

Vicon V960D-N312 Gebrauchsanweisung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung

Lumens

Lumens VC-A50PNW Bedienungsanleitung