Viessmann Vitocell 100-E Kurzanleitung

Installation and service instructions

for contractors

VIESMANN

Vitocell 100-E

Type SVPB

Heating water buffer cylinder

600 to 950 l

VITOCELL 100-E

6154019 GB 4/2020 Please keep safe.

Please follow these safety instruc-

tions closely to prevent accidents

and material losses.

Safety instructions explained

Danger

This symbol warns against the risk

of injury.

!Please note

This symbol warns against the risk

of material losses and environmen-

tal pollution.

Note

Details identified by the word "Note"

contain additional information.

Target group

These instructions are exclusively inten-

ded for qualified contractors.

■Work on electrical equipment may only

be carried out by a qualified electrician.

■The system must be commissioned by

the system installer or a qualified per-

son authorised by the installer.

Regulations to be observed

■National installation regulations

■Statutory regulations for the prevention

of accidents

■Statutory regulations for environmental

protection

■Codes of practice of the relevant trade

associations

■Relevant country-specific safety regu-

lations

Working on the system

■Isolate the system from the power sup-

ply (e.g. by removing the separate fuse

or by means of a mains isolator) and

check that it is no longer live.

■Safeguard the system against recon-

nection.

!Please note

Electronic assemblies can be dam-

aged by electrostatic discharge.

Prior to commencing any work,

touch earthed objects such as heat-

ing or water pipes to discharge

static loads.

Danger

Hot surfaces can cause burns.

■Before maintenance and service

work, switch OFF the appliance

and let it cool down.

■Never touch the hot surfaces of

uninsulated pipes and fittings.

Safety instructions

6154019

Danger

Floors that are wet or damp with

water or glycol based liquids can

cause injury due to slipping and fall-

ing.

■Keep the floor clean and dry dur-

ing installation and maintenance

work.

■Wear non-slip shoes.

Danger

Broken-off fragments of insulation

material can cause death by suffo-

cation if inhaled or swallowed.

■Do not let children play in the

installation room.

■Keep the installation room clean

after installation and maintenance

work.

Repair work

!Please note

Repairing components that fulfil a

safety function can compromise the

safe operation of the system.

Replace faulty components only

with genuine Viessmann spare

parts.

Auxiliary components, spare and wearing parts

!Please note

Spare and wearing parts that have

not been tested together with the

system can compromise its func-

tion. Installing non-authorised com-

ponents and making non-approved

modifications or conversions can

compromise safety and may invalid-

ate our warranty.

For replacements, use only original

spare parts supplied or approved by

Viessmann.

Safety instructions

Safety instructions (cont.)

6154019

1. Information Disposal of packaging ............................................................................ 5

Symbols ................................................................................................. 5

Intended use .......................................................................................... 5

Product information ................................................................................ 6

System examples .................................................................................. 6

Spare parts lists ..................................................................................... 6

2. Preparing for installation Connections ........................................................................................... 7

3. Installation sequence Siting the cylinder .................................................................................. 8

Fitting the lower thermal insulation mat and aligning the cylinder body 8

Fitting the thermometer sensor (if supplied) and cylinder temperature

sensor .................................................................................................... 9

Mounting the Vitotrans ........................................................................... 10

Fitting the thermal insulation jacket ....................................................... 12

Fitting the cover strips ............................................................................ 13

Fitting the cover ..................................................................................... 15

Making the connections on the heating water side ................................ 15

Connecting the equipotential bonding ................................................... 16

4. Commissioning/service

reports

................................................................................................................ 17

5. Specification ................................................................................................................ 18

6. Disposal Final decommissioning and disposal ..................................................... 19

7. Certificates Declaration of conformity ....................................................................... 20

8. Keyword index ................................................................................................................ 21

Index

6154019

Please dispose of packaging waste in line with statu-

tory regulations.

Symbols

Symbol Meaning

Reference to other document containing

further information

Step in a diagram:

The numbers correspond to the order in

which the steps are carried out.

Warning of material losses and environ-

mental pollution

Live electrical area

Pay particular attention.

■Component must audibly click into place.

■Acoustic signal

■Fit new component.

■In conjunction with a tool: Clean the sur-

face.

Dispose of component correctly.

Dispose of component at a suitable collec-

tion point. Do not dispose of component in

domestic waste.

Intended use

The appliance is only intended to be installed and

operated in sealed unvented systems that comply with

EN 12828 / DIN 1988, or solar thermal systems that

comply with EN 12977, with due attention paid to the

associated installation, service and operating instruc-

tions. DHW cylinders are only designed to store and

heat water of potable water quality. Heating water buf-

fer cylinders are only designed to hold fill water of pot-

able water quality. Only operate solar collectors with

the heat transfer medium approved by the manufac-

turer.

Intended use presupposes that a fixed installation in

conjunction with permissible, system-specific compo-

nents has been carried out.

Commercial or industrial usage for a purpose other

than heating the building or DHW shall be deemed

inappropriate.

Any usage beyond this must be approved by the man-

ufacturer for the individual case.

Information

Disposal of packaging

6154019

Information

Incorrect usage or operation of the appliance (e.g. the

appliance being opened by the system user) is prohibi-

ted and results in an exclusion of liability.

Incorrect usage also occurs if the components in the

system are modified from their intended use (e.g.

through direct DHW heating in the collector).

Adhere to statutory regulations, especially concerning

the hygiene of potable water.

Product information

Vitocell 100-E, type SVPB (600, 750 and 950 l

capacity)

■Steel heating water buffer cylinder for storing heating

water in combination with heat pumps, solar thermal

systems, solid fuel boilers and heat recovery.

■With the option to fit a Vitotrans 353

■Suitable for systems to EN 12 828 and DIN 4753.

■For dimensions and weight, see page 18.

System examples

Available system examples: See www.viessmann-

schemes.com.

Spare parts lists

Information about spare parts can be found at

www.viessmann.com/etapp or in the Viessmann

spare part app.

Information

Intended use (cont.)

6154019

Information

Front

Back

AThermometer sensor fixing (underneath the thermal

insulation)

BThermometer, up to 4 pce (accessories)

CHeating water flow G 1

DReturn stratification G 1

EHeating water return G 1

AHeating water flow 1 (to the heating circuits)/air

vent valve

BHeating water flow 2 (from the heat generator)

CClamping system for cylinder temperature sensor

(behind the thermal insulation)

DThermometer sensor fixing (behind the thermal in-

sulation)

EHeating water flow 3

FHeating water return 1

GClamping system for cylinder temperature sensor 2

and thermometer sensor (behind the thermal insu-

lation)

HHeating water return 2 (from the heating circuits)

KClamping system for cylinder temperature sensor 3

and thermometer sensor (behind the thermal insu-

lation)

LHeating water return 3 (from the heating circuits)

MClamping system for cylinder temperature sensor 4

(behind the thermal insulation)

NHeating water return 4 (to the heat generator)/drain

OThermometer sensor fixing (behind the thermal in-

sulation)

Preparing for installation

Connections

6154019

Installation

!Please note

Exposure to frost can damage the appliance.

Install the buffer cylinder in a room that is free

from the risk of frost and draughts. Otherwise,

the buffer cylinder must be drained if there is a

risk of frost while it is not in use.

■Provide adequate clearance from the wall to allow for

operation of the temperature controller (if installed).

■Placing the heating water buffer cylinder on a plinth

will make the room easier to clean.

■Use adjustable feet to level the buffer cylinder.

!Please note

The thermal insulation must not come into con-

tact with naked flames.

Exercise caution when welding and brazing.

Fitting the lower thermal insulation mat and aligning the cylinder body

Fig. 1

ABag containing type plate

BBag containing 3 adjustable feet

3. Insert the adjustable feet into the legs as far as

they will go, then adjust them to level the cylinder

body.

Installation sequence

Siting the cylinder

6154019

Installation

Note

Only use one or two of the adjustable feet to level the

cylinder body. At least one of the adjustable feet must

remain fully screwed in.

≤35

Fig. 2

Do not extend the adjustable feet beyond a total

length of 35 mm.

Fitting the thermometer sensor (if supplied) and cylinder temperature sensor

Fig. 3

1. Guide the thermometer sensor through the cover

strip and insert the thermometer.

Installation sequence

Fitting the lower thermal insulation mat and… (cont.)

6154019

Installation

2. Guide the upper thermometer sensor through the

lifting eye, insert it into the clamping bracket as far

as it will go and tighten the wing nut.

Note

The cover strip is held in its vertical position by the

coiled capillaries. This is necessary for the remain-

der of the installation.

3. Route the thermometer sensor capillaries to the

back of the cylinder.

4. Undo the nuts.

5. Place the clamping system onto the threaded studs

and align.

6. Tighten the nuts.

7. Depending on where the sensor is being fitted,

secure the thermometer sensor in the clamping

bracket or push as far as it will go into clamping

systems A.

Push cylinder temperature sensor into the

clamping system as far as it will go.

Note

■Never wrap insulating tape around the sensors.

■When the thermal insulation is being fitted, the

cylinder temperature sensor leads are routed

outwards through the apertures (slots) in the rear

cover strip.

Mounting the Vitotrans

Fig. 4

Installation sequence

Fitting the thermometer sensor (if supplied) … (cont.)

6154019

Installation

Andere Handbücher für Vitocell 100-E

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Viessmann Boiler Handbücher

Viessmann

Viessmann Vitotherm ES4 Bedienungsanleitung

Viessmann

Viessmann VITOCELL 300B Betriebsanleitung

Viessmann

Viessmann Vitodens 200-W System Betriebsanleitung

Viessmann

Viessmann VITOCELL 300 EVI Series Bedienungsanleitung

Viessmann

Viessmann Vitosol 111-F Betriebsanleitung

Viessmann

Viessmann VITOWELL EASY C1 Bedienungsanleitung

Viessmann

Viessmann VITOCELL 300V Gebrauchsanweisung

Viessmann

Viessmann Vitodens 111-W Bedienungsanleitung

Viessmann

Viessmann VITOWELL EASY P1 Bedienungsanleitung

Viessmann

Viessmann Vitocell 100-E SVW 200 l Kurzanleitung

Viessmann

Viessmann Vitocell 100-E Betriebsanleitung

Viessmann

Viessmann VITOCELL 300W Service-Handbuch

Viessmann

Viessmann Vitocell 360-M Kurzanleitung

Viessmann

Viessmann VITOCELL-V 100 Bedienungsanleitung

Viessmann

Viessmann Vitocell 140-E Betriebsanleitung

Viessmann

Viessmann VITOCELL 300 EVI Series Bedienungsanleitung

Viessmann

Viessmann VITOCELL 100-VH Handbuch

Viessmann

Viessmann EHA Series Gebrauchsanweisung

Viessmann

Viessmann VITOCELL-H 300 Bedienungsanleitung

Viessmann

Viessmann VITOCELL 100-B Betriebsanleitung

Viessmann

Viessmann VITOCELL 100-B Betriebsanleitung

Viessmann

Viessmann Vitocell 100-E Kurzanleitung

Viessmann

Viessmann VITOCELL 100-B Bedienungsanleitung

Viessmann

Viessmann Vitosol 100 Bedienungsanleitung

Beliebte Boiler Handbücher anderer Marken

Kenmore

Kenmore 153.582400 Bedienungsanleitung

Applimo

Applimo Edel AIR Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

clage

clage E-Mini Series Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-180 Bedienungsanleitung

Bradford White

Bradford White EF Series Bedienungsanleitung

Eccotemp

Eccotemp 40-H Bedienungsanleitung

Dimplex

Dimplex ECSd125-580 Leitfaden

Dux

Dux 32FCR6N Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Fehlerbehebungshandbuch

Noritz

Noritz N-132M Gebrauchsanweisung

TESY

TESY GCV7/4S 10047 Technisches Datenblatt

A.O. Smith

A.O. Smith Gphe 50 Bedienungsanleitung

Koryo

Koryo KWHZF15Y Bedienungsanleitung

Pentair

Pentair PSC-14-4-02 Bedienungsanleitung

GE 40M06AAG Montageanleitung

Thermor

Thermor AEROMAX SPLIT 2 Bedienungsanleitung

American Hometec

American Hometec AHQ-B03X Bedienungsanleitung