Viessmann VITOWELL EASY P1 Bedienungsanleitung

VITOWELL EASY P1

117 mm

VITOWELL EASY P1

Instant Water Heater

Operation

Manual

1. Front Cover

2. LED Indicators

3. Temperature Control Knob

4. Stop Valve

5. Rail Support / Wall Bracket

6. Handshower

7. Adjustable Shower Holder

8. Slider Rail

9. PVC Hose

10. Soap Tray

11. Heater Base

12. Thermostat

13. Heater Tank

14. Terminal Block

15. Main PCB Board

16. Water Outlet Connection

17. TRIAC

18. Water Inlet Connection

19. Flow Sensor

20. Mesh Filter

21. LED Board

22. Thermistor

Parts Identification

Installation must be carried

out by a qualiﬁed personnel and

in compliance to the local

authority regulations.

This instant water heater

must be permanently connected

to the direct main current supply.

The use of a plug and socket is

not recommended.

For the correct size of wire

conductor corresponding to

different electrical loading,

please refer to the Electrical

Loading Table.

This instant water heater

operates at a minimum water

ﬂow rate of 2.0 L/min and

maximum working pressure of 6

bars. For direct connection to the

water tank, the heater must have

a minimum distance of 1.0m

below the water tank.

This instant water heater will

not function if there is insufficient

water ﬂow (min 2.0 L/min) to

trigger the ﬂow switch.

The thermostat will automati-

cally cut off the power supply if it

has sensed an abnormal rise in

water outlet temperature.

Important Safety Information

Products manufactured by us are

safe provided they are installed, used

and maintained in good working order

in accordance with our instructions and

recommendations. Always refer to this

manual if you have any doubt.

The appliance must be earthed.

Improper grounding could cause

electric shock.

If any of the following conditions

occur, immediately switch off the mains

and contact the sales agent for repair.

Never attempt to repair the unit

yourself.

-If the heater begins to make an odd

noise, smell or smoke.

-Water temperature can not be

controlled.

-If the instant water heater shows signs

of a distinct change in performance.

-If found water leakage from inside.

The appliance is not intended for

use by person (including children) with

reduced physical, sensory or mental

capabilities, or lack of experience and

knowledge, unless they have been

given supervision responsible for their

safety.Children should be supervised at

all times when using the unit to ensure

that they do not play with the appliance.

User is advised to test and adjust

the water temperature before

showering.

In times of lightning/thunder, switch

off the electric supply to the instant

water heater in advance to protect the

instant water heater against possible

damage.

Metallic/chrome hose and conduc-

tive control valve shall not be used.

(Malaysia only)

Note: When removing the instant water

heater from package, small amount of

water may be found inside. This is

normal as the unit is tested during

manufacturing process.

260 mm

137 mm

Rubber

Washe

Rubber

Washe

Screw A

* *

Heater Unit Installation

Select a suitable position in the

bathroom.

Pull out the Temperature Control

Knob and then remove the Screw A at

the bottom of the unit.

Remove the Front Cover from the

bottom and then lift up the Front Cover.

Mark 3 Screw points of the Heater

Base on the wall. (Refer * marking)

The Instant Water Heater position

should be1.5m above the bathroom

floor.

Mark 2 screw points of the Slider

Rail beside the heater. It is recom-

mended that the top of the portion is in

level with the top of Instant Water

Heater.

Use 6mm diameter drill and make

the wall plug holes in depth of 34mm.

Insert the wall plugs and mount the

Instant Water Heater firmly in position

with the screws provided.

Insert the Shower Holder and Soap

Tray into the Slider Rail.

Mount the Slider Rail to the Rail

Bracket.

Remove the cap from the Rail

Bracket and screw the Bracket to

marked position. Replace the cap.

Plumbing Procedure

This Instant Water Heater is a

single point system and the

“Water Outlet” can only

be ﬁtted to the PVC Hose and

Handshower set provided. NO

CONTROL VALVE OR

FITTING CAN BE FITTED TO

THE WATER OUTLET.

Connect the Stop Valve to the

Water Inlet with washer. Use

correct tools to tighten the

connection and be careful not to

over tighten and damage the

plastic nut.

Connect the incoming water

piping to the Stop Valve (1/2”

BSP). Make sure to put the Mesh

Filter between Stop Valve and

incoming water piping.

If in any case, the Stop Valve

is not used or omitted, make

sure to put the Mesh Filter

between the heater unit inlet pipe

and incoming water pipe.

Turn on the water mains to

drain out all plumbing dirts, at the

same time ﬁll up the heater tank.

THE HEATER TANK MUST BE

FILLED UP WITH WATER

BEFORE TURNING ON THE

ELECTRICITY SUPPLY TO

PREVENT ANY DRY BURNT

DAMAGE TO THE HEATING

ELEMENT.

Connect the PVC Hose and

Handshower to the outlet of the

Instant Water Heater, be sure to

put in the Washer.

Hook the Handshower to the

Sliding Rail Shower Holder and

adjust to your ideal position.

Check if any water leakage.

Do not use white tape during

piping installation.

THE WATER INLET AND

OUTLET MUST BE INSTALLED

CORRECTLY , OTHERWISE IT

MAY CAUSE A DAMAGE TO

THE HEATING ELEMENT.

DO NOT APPLY PLUMBING

CEMENT ON CONNECTION.

WHENEVER NECESSARY, USE

ONLY THREAD OR SEALING

TAPE.

PROCEDURE:

Insert the cable through ‘A’ for side

entry or ‘B’ for wall embedded cable by

cutting a hole through the source cord

rubber holder.

Connect the cable to Terminal Block

and fully tighten them as follow

BROWN or RED — LIVE (L)

BLUE or BLACK — NEUTRAL (N)

GREEN/YELLOW — EARTH ( )

When replace back the Front Cover,

please take note the below procedure:

To ensure the correct position, turn

the Temperature VR Knob insert to

OFF position as shown in Fig A. (at the

Heater Base)

To install the Front Cover, turn the

Temperature Control Knob to OFF

position to align with the VR Knob

connect the LED display cable from

front cover to the Main Control PCB.

Clamp the cable to the correct position.

CHECK IF THE WIRING CONNEC-

TION IS CORRECT and replace the

cover.

Fix back the Screw A.

Position

At Off

Electrical Installation

FUSE

ON/OFF

Fuse Distributor Board

Miniature Circuit Breaker (MCB)

Double PVC cable over 2.5mm²

ON/OFF Double Pole Switch

Cable

NOTE:

Refer to Table 1. for

electrical loading

and correct size of

wire conductor.

BROWN — LIVE (L)

or RED

BLUE or BLACK — NEUTRAL (N)

GREEN — EARTH ( )

or GREEN/YELLOW

This appliance must be

EARTHED. Improper grounding

could cause electrical shock.

Remember to SWITCH OFF at

mains before carrying out any

electrical work.

Refer to the Electrical Loading

Table for the correct cable size.

Use double coated flexible cable

having nominal cross-sectional

area 2.5mm².

Lead the power cable from the

MCB to a “ON/OFF” double pole

linked switch having a contact

separation of at least 3mm in all

poles outside the bathroom, then

lead a cable connected to

Terminal block inside the unit.

Position

At Off

Electrical Loading Table

Test Run

Turn on the water supply and Stop Valve, the water will flow through the

Handshower.

Switch on the electrical supply.

Turn the Temperature Control Knob to ‘ON’, the Red Indicator light (Power)

will turn on, hot water will flow out within a few seconds. The more Temperature

Control Knob being turned in clockwise direction, the hotter the shower is.

The shower might not be hot enought even at ‘MAX’ position if incoming water

supply from the mains is too cold or pressure water is too high. In this case, you

may adjust the Stop Valve to reduce the water inflow in order to get the desired

showering temperature.

Switch OFF the electricity supply after shower.

(MalaysiaModal)

Voltage

(AC)

Power

(kW)

Current

(A)

Minimum Conductor Size (csa)

mm² Conduit Cable Flexible Cable

On/Off

Switch (A)

Fuse /

MCB (A)

240~

50/60Hz

230~

50/60Hz

220~

50/60Hz

Handshower Spray Action

Clean the Handshower Head

holes by using the soft brush

from time to time.

Recommended once a week.

Note: Take care not to

damage the holes of the

Handshower Head during

cleaning.

This innovative adjustable

Handshower has 5 different spray

actions (STANDARD, SOOTHE,

JUMBO, MIX, MASSAGE). The

actions are described as above.

FILTER UNIT

CLEANING

OPEN

INTERNAL

STRAINER

OPENCLOSE

FLOW REGULATOR

MESHFILTER

BUILT-IN FILTER

Maintainance

Read the section ‘IMPORTANT

SAFETY INFORMATION’ first.

CLEANING PRECAUTION!

Do not use thinner, alcohol, petrol or

any other organic solution to clean the

set, use only a damp cloth with mild

detergent.

CLEAN THE FILTER REGULARLY.

There are two filters located at the stop

valve, one is Mesh Filter (installed at

the incoming water supply), another

one is the built-in filter as shown.

Clean the Mesh Filter regularly to

prevent blockage. Remove the built-in

filter by turn it anti-clockwise as shown .

Take out the Filter and flush it with

water to remove any trapped sendi-

ments.

Troubleshooting

Problem/Symptom Cause Action/Cure

Electric Water

Heater fail to

operate, no power.

Interrupted power

supply.

Electric Water Heater

malfunction.

Check the wire connection and main power

supply. If it still fail to operate, contact

Viessmann Customer Service Call Centre.

Check other appliances are having same

phenomenal and contact local Electricity Supply

Company. If it still fail to operate, contact

Viessmann Customer Service Call Centre.

Water too hot. Not enough water

flowing through the

shower.

Increase flow rate via water flow controler or 3

in 1 Stop valve.

Blocked of shower head - clean or replace.

Blockage in water

supply.

Check if 3 in 1 stop valve are fully turns on.

Cleaning Mesh Filter and Built In Filter.

Incoming water

temperature too high.

Reduce the setting temperature via

temperature adjuster.

Water hot after

close and reopen

of 3 in 1 Stop

Valve or Water

Tap.

Water temperature

higher than set

temperature when 3 in

1 Stop Valve or Water

Tap is OFF a while

and reopen again.

Water too cool or

cold.

Too much water flow. Reduce flow rate via water flow controller or 3

in 1 Stop Valve.

Water pressure below

minimum required and

water heater not

function.

Check water supply from mains or tank fed. If

tank fed, replumb to mains water supply and

check if the water pressure is enough. If mains

fed, make sure that mains 3 in 1stop valve is

fully turns on and that there are no other

restrictions in the water supply while water

heater is in use.

Avoid shower with water output during that

period. Let the water flow few seconds before

continue bathing.

Inhaltsverzeichnis

Andere Viessmann Boiler Handbücher

Viessmann

Viessmann Vitocell 140-E Kurzanleitung

Viessmann

Viessmann Vitosol 100 Bedienungsanleitung

Viessmann

Viessmann Vitodens 111-W Bedienungsanleitung

Viessmann

Viessmann VITOCELL 100-B Betriebsanleitung

Viessmann

Viessmann Vitotherm ES4 Kurzanleitung

Viessmann

Viessmann Vitocell 100-E SVW 200 l Kurzanleitung

Viessmann

Viessmann VITOCELL 100-B Bedienungsanleitung

Viessmann

Viessmann VITOTHERM EI5 Series Kurzanleitung

Viessmann

Viessmann VITOWELL EASY D1 Bedienungsanleitung

Viessmann

Viessmann Vitocell 140-E Betriebsanleitung

Viessmann

Viessmann Vitotherm ES4 Bedienungsanleitung

Viessmann

Viessmann VITOCELL 300V Kurzanleitung

Viessmann

Viessmann Vitocell 100 CHA Series Leitfaden

Viessmann

Viessmann Vitocell 360-M Kurzanleitung

Viessmann

Viessmann VITOWELL comfort Bedienungsanleitung

Viessmann

Viessmann VITOCELL-V 100 Original Betriebsanleitung

Viessmann

Viessmann Vitotherm ES4.A10 K Kurzanleitung

Viessmann

Viessmann VITOCELL 300V Gebrauchsanweisung

Viessmann

Viessmann VITOCELL 300B Betriebsanleitung

Viessmann

Viessmann Vitocell 100 Bedienungsanleitung

Viessmann

Viessmann Vitodens 200-W System Betriebsanleitung

Viessmann

Viessmann VITOWELL EASY C1 Bedienungsanleitung

Viessmann

Viessmann VITOCELL 100-B Bedienungsanleitung

Viessmann

Viessmann Vitosol 111-F Betriebsanleitung

Beliebte Boiler Handbücher anderer Marken

Kenmore

Kenmore 153.582400 Bedienungsanleitung

Applimo

Applimo Edel AIR Bedienungsanleitung

STIEBEL ELTRON

STIEBEL ELTRON Eltronom SHU 5 S Bedienungsanleitung

clage

clage E-Mini Series Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-180 Bedienungsanleitung

Bradford White

Bradford White EF Series Bedienungsanleitung

Eccotemp

Eccotemp 40-H Bedienungsanleitung

Dimplex

Dimplex ECSd125-580 Leitfaden

Dux

Dux 32FCR6N Bedienungsanleitung

Toyotomi

Toyotomi Oil Miser OM-148 (Type D) Fehlerbehebungshandbuch

Noritz

Noritz N-132M Gebrauchsanweisung

TESY

TESY GCV7/4S 10047 Technisches Datenblatt

A.O. Smith

A.O. Smith Gphe 50 Bedienungsanleitung

Koryo

Koryo KWHZF15Y Bedienungsanleitung

Pentair

Pentair PSC-14-4-02 Bedienungsanleitung

GE 40M06AAG Montageanleitung

Thermor

Thermor AEROMAX SPLIT 2 Bedienungsanleitung

American Hometec

American Hometec AHQ-B03X Bedienungsanleitung