Viper 426FS Bedienungsanleitung

Table of Contents

Warranty............................................................................. 2

What is Included ................................................................ 3

Standard Configuration ..................................................... 4

Using your System ............................................................ 5

Arming ........................................................................ 5

Armed while Driving ............ ...................................... 6

Disarming ................................................................... 6

High Security Disarm ................................................. 6

Disarming without a transmitter .................................. 7

Silent Mode .. ............................................................. 7

Panic Mode ................................................................. 7

Valet Mode................................................................... 8

Nuisance Prevention Circuitry ......................................... 8

Diagnostics......................................................................... 9

Arming Diagnostics ..................................................... 9

Disarming Diagnostics ................................................. 10

Table of Zones .................................................................... 10

Code Hopping Explained .................................................. 11

Programming Options ........ ................................................ 11

Glossary of Terms........ ....................................................... 13

Security & Convenience Expansions... ................................ 14

5Years Limited Lifetime Warranty: Model 260 HF

Directed Electronics, Inc., promises to the original purchaser to repair or replace with a comparable recondi-

tioned model any electronic control module which proves to be defective in workmanship or material under

normal use during 5 years, AS LONG ASTHE SYSTEM WAS SOLD, INSTALLED, AND SERVICES BY AN

AUTHORIZED DEI DEALER,(LIMITED LIFETIMEWARRANTY COVERSTHE SYSTEM FORTHE ORIGI-

NAL OWNER OF THE ORIGINAL VEHICLE IN WHICH THE SYSTEM WAS INSTALLED). After 5 years, a

flat cost will be charge to repair the product .If warranty service is necessary you must have a clear copy of

your sales receipt containing all the informations mentionned below. All components other than the unit,

including without limitation the siren, the remote transmitters and the associated sensors and accessories,

carry a one-year warranty from the date of purchase.

This warranty is void if the product has been damaged by accident, unreasonable use, neglect, impoper

service or other cases not arising out of defects in materials or fabrication.This warranty is non transferable

and does not apply to any unit that has been modified or used in a manner contrary to its intended purpose

and does not cover batteries.This warranty does not cover labor costs for the removal, diagnosis, trouble-

shooting, removal and reinstallation of the unit. For service on an out-of-warranty product, a flat rate fee by

model will be charged.Contact your authorized dealer to obtain the service charge for your unit.

IMPORTANT

DEIsecurity systems,including thisunit,are deterrents againstpossibletheft.DEIis not offeringa guarantee

orinsurance againstvandalism,damage ortheftof theautomobile,its parts orcontents;andherebyexpressly

disclaims any liability whatsoever, including without limitation, liability for theft, damage and / or vandalism.

The product warranty is automatically void if its date code or serial number is defaced , missing, or altered.

Any defective unit must be returned to Directed Electronics Inc., postage prepaid by an authorized dealer.

Make sure you have all af the following

information from your

VIPER® dealer:

A clear copy of the sales receipt, showing the following:

• Date of purchase • Automobile license number

•Your full name and address •Vehicle identification number

• Authorized dealer’s company name and address • Security options installed on automobile

•Type of alarm installed • Installation receipts

•Year, make, model and color of the automobile

What is Included

• The control unit

• A pair of two-button transmitters

• A Stinger®Doubleguard®dual-stage shock / impact sensor

• The Revenger®Soft Chirp®six-tone programmable siren

• The red status LED indicator

• A push-button Valet® switch

CONGRATULATION onthepurchaseofyourstate-of-the-artvehiclesecurity

system. By carefully reading this guide prior to using your system, you will

maximize the use of this system and its features.You ca print additional or

replacement copies of this manual by accessing the DEI® Internet website

at www.dei.com.

THE SYSTEM REQUIRES NO SPECIFIC MAINTENANCE. Your remote control

is powered by a miniature 12V battery, type GP23A, that will last

approximately one year under normal use. When the battery weakens,

operating range will be reduced and the LED on the remote will light dim.

It is also necessary to keep your proof of purchase..

-3-

LED

Arm

Disarm

Panic

Silent Mode

Auxiliary

Output

Standard Configuration

Button I

The arm, disarm and panic functions, are usually controlled by button I.

Button II

Silent ModeTM and an optional auxiliary function, such as trunk release, are

usually controlled by button II.

Silent Mode works by pressing button II for less than one second.

Trunk release requires you to press button II for 1.5 seconds.

-4-

Using your System

Arming

You can turn on, or arm, the system by pressing Button I of your

transmitter for one second. When the system arms, you will hear a short

siren sound,or chirp, and see the parking lights flash once. If the vehicle’s

power door locks are controled by the system, the doors will lock.

While the system is armed, the Status LED will flash about twice a

second, showing that the system is actively protecting your vehicle. If you

hear a second chirp after arming and see the Status LED flashes in groups,

see Diagnostics section.This extra chirp is called Bypass Notification.

The system also can be programmed to arm itself automatically (called

passive arming). If the system is programmed for passive arming, it will

automatically arm 30 seconds after the ignition is turned off and the

system“sees”youleave thevehiclebyopeningandclosingadoor.Whenever

the system is in its 30 second passive-arming countdown, the status led will

flash twice as fast as it does when the system is armed.

NOTE: If any protected entry point (such as a door or a switch-

protected trunk or hood) is open, the system will not passively

arm, unless forced passive arming is progarmmed on. (See

ProgrammingOptionssection).Additionally,each timea sensor is

triggered duringthearmingcountdown,the 30secondcountdown

starts over.)

When armed, your vehicle is protected in the following ways:

• Lightimpactswill trigger theWarnAway®signal.When triggered, thesiren

will chirp and the parking lights will flash for a fey seconds.

•Heavy impacts will trigger the system. The trigger sequence is 30 se-

conds of constant siren and flashing parking lights.

-5-

• If a door is opened, the system will immediately start chirping the siren

andflashing theparking lights.Threesecondslater,thesirenoutput chan-

ges to a continuous blast. This progressive reponse gives you time to

disarm the system with your transmitter if you inadvertently open the

door while the system is armed, while still providing instant response

(even if the door is immediately closed).

• Turningontheighitionkeywilltripthesametwo-stagereponse asopening

a door.

Armed While Driving

Your system can be armed while driving the vehicle! Simply press

Button I on your transmitter while the vehicle is running.The system will

chirp once and then once more to indicate that the ignition is on. The

system will not respond to any input except the door triggers and the

starter kill relay (if installed) will not be activated.Once you have reached

your destination, the system must be disarmed by pressing Button I on

the transmitter once more.The siren will chirp twice and the LED will stop

flashing.If you do not disarm the system, it will trigger when the any door

is opened to exit the vehicle.

Disarming

To turn off, or disarm the system, press Button I again.You will hear

two chirps, and te parking lights will flash twice. If power locks are

controlled by the system, the doors will unlock. If the siren chirps either

four or five times when disarming, see Diagnostics section.This is called

Tamper Alert.

High Security Disarm

Your system includes a High Security Disarm feature. During the

triggered sequence, using the transmitter to disarm it will only stop the

triggered sequence (the siren will stop and the parking lights will stop

flashing). However, the system will remain armed and the doors will stay

locked.This is extremely useful if you must stop the system from sounding,

but are unable to check the vehicule visually.The trigger will stop, but the

vehicle will remain protected.

To disarm with the transmitter during a trigger, press Button I on your

trasmitter. The siren will stop sounding. Next press Button I once more

and the system will chirp four or five times (reporting the trigger) and

disarm.

-6-

Disarming Without a Transmitter

This feature allows you to disarm the system without the transmitter

should it be lost, damaged or disabled. In order to disarm without a

transmitter, you must have the vehicle’s ignition key and know where the

Valet button is. Be sure to check with the installer for the location of the

Valet button.

Silent ModeTM

To temporarily turn off the arm of disarm chirps, use Silent ModeTM.

Simply press Button II briefly before arming or disarming, and the confir-

mation chirp(s) will be eliminated for that one operation only. If you want

the arm/disarm chirps turned off permanently, your dealer can do this for

you.

NOTE:The Warn Away®response to lighter impact is bypassed if

thesystemisarmedusingSilentMode.Thisensuresthatnochirps

will be emittted by the siren in an area you want chirp-free. The

system is still fully able to trigger. Only the Warn Away response

is defeated.

Panic Mode

If you are threatened in or near your vehicle, you can attract attention

by triggering the system with you transmitter! Just press Button I for 1.5

seconds, and you will enter Panic Mode. The siren will sound and the

parking lights will flash for 30 seconds. To stop Panic Mode at any time,

press Button I on the transmitter again.

Turn on the ignition.Push theValet switch

within15seconds.Thesystemshouldnow

disarm.Ifit doesnot,you may havewaited

too long, so turn the ignition off and on

and try again.

-7-

Valet® Mode

You can prevent your system from automatically arming and triggering

by using Valet Mode. This is very useful when washing the vehicle or

having it serviced. In Valet Mode, the system will not arm, even with the

transmitter, but all convenience functions (door locks, trunk release, etc.)

will work normally.

To enter or exit Valet Mode with the Valet switch:

Using Remote Valet Mode as you enter or exit the vehicle:

• Open any door.

• Press Button I (or the arm/disarm button).

• Press Button II (or the function 2 button).

• Press Button I again.

The Status LED will light steady if you have entered Valet Mode, and it

will go out if you exited Valet Mode.

Nuisance Prevention®Circuitry

Your system has DEI’s Nuisance Prevention® Circuitry (NPCTM). It

prevents annoying repetitive trigger sequences due to faulty door pin

switches or environmental conditions such as thunder, jackhammers,

airport noise, etc.

Here’s how it works: Let’s say the alarm triggers three times.Each time,

the same sensor or switch is triggering the alarm. The three triggers are

within 60 minutes of each other.NPCTM (Nuisance Prevention® Circuitry)

will interpret this pattern of triggers as false alarms.After the third trigger,

NPC ignores, or bypasses, that sensor or switch (along with any other

sensors or switches sharing the same zone).

Turn ignition to “run” position, then turn to

“off” position. Press and release the Valet

switch within 10 seconds.The Status LED will

light steady if you have entered Valet Mode,

and it will go out if you exited Valet Mode.

-8-

If the bypassed sensor tries to trigger the system while it is being by-

passed, the 60 minute bypass period will start over. This ensures that a

sensor that a sensor that continuously triggers will remain bypassed.

Doors are covered by NPC differently;If the alarm is triggered by an open

door for three full cycles (one-and-one-half minutes), the doors will be

bypassed until the trigger ceases.

NOTE: Arming and disarming the system does not reset this function!

The only ways to reset a bypassed zone are for it to remain untriggered

for 60 minutes, or to turn on the ignition.If testing your system, it is impor-

tant to remember that the NPC programming can cause zones to be

bypassed and seem to stop working. If five chirps are heard when dis-

arming, NPC has been engaged. If you wish to clear the NPC memory,

turn the ignition on.

Diagnostics

The Microprocessor at the heart of your system is constantlly monito-

ring all of the switches and sensors connected to it. It detects any faulty

switches and sensors and prevents them from disabling the entire system.

The microprocessor will also record and report any triggers that occured

during your absence.

Arming Diagnostics

If the system is armed with an input active (door open, sensor

triggering, etc.) the unit will chirp once when arming and then one more

time a few seconds later.This is called Bypass Notification.

NOTE: Bypass Notification will not occur when using Silent Mode

or if chirps have been programmed OFF.

The system will ignore the input that was active when it was armed

until it goes away. Three seconds later it will monitor that input normally.

For example, if your car has interior light exit delay, and you arm the

system before the interior light goes out, you may get Bypass Notifica-

tion.Once the light goes out, however, the doors are monitored normally.

-9-

Disarming Diagnostics

Extra disarm chirps are the Tamper Alert. If four chirps are heard when

disarming, the system was triggered so many times that Nuisance

Prevention®Circuitry has bypassed that zone. In either case, the Status

LED will indicate which zone was involved (seeTable of Zones section).The

system will retain this information in its memory, and chirp four of five times

each time it is disarmed, until the next time the ighition key is turned on.

Table of Zones

The zone number is the number of LED flashes used by the system

to identify that input. the standard input assignments are listed below,

along with spaces to write in any optional sensors or switches you have

had installed.

NOTE: If the Warn Away® response is triggered, the LED will not

report it.

-10-

ZONE DESCRIPTION DEALER-INSTALLED

(# of LED FLASHES)

1 Instant trigger of optional

sensors

2 A heavier impact trigger from

the shock sensor

3 Door switch circuit

4 Ignition

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Viper Autoalarmanlage Handbücher

Viper

Viper 300+ Bedienungsanleitung

Viper

Viper 771XV Bedienungsanleitung

Viper

Viper 5104 1-Way Bedienungsanleitung

Viper

Viper 200 MAX Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung

Viper

Viper 5806V Bedienungsanleitung

Viper

Viper 5900 Bedienungsanleitung

Viper

Viper 211HV Bedienungsanleitung

Viper

Viper 330V Bedienungsanleitung

Viper

Viper 4218V Bedienungsanleitung

Viper

Viper 500HF Bedienungsanleitung

Viper

Viper 4606V Bedienungsanleitung

Viper

Viper 4704 Bedienungsanleitung

Viper

Viper 690XV Bedienungsanleitung

Viper

Viper Car Alarm 420 ESP Bedienungsanleitung

Viper

Viper SmartStart 3000 Series Bedienungsanleitung

Viper

Viper 791 XV Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung

Viper

Viper 446 Series Bedienungsanleitung

Viper

Viper SmartStart 3000 Series Bedienungsanleitung

Viper

Viper SmartStart 3000 Series Bedienungsanleitung

Viper

Viper 5706V Bedienungsanleitung

Viper

Viper 5606V Bedienungsanleitung

Viper

Viper 3606V Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Ultra Start

Ultra Start 450 SERIES Bedienungsanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Excalibur

Excalibur AL-1860-EDPB Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Clifford

Clifford Nova 3 Bedienungsanleitung