Viper SL1610SE Bedienungsanleitung

[866] 418-4737

[866] 41-VIPER Rev.00(05-06)

VV67149U

SERIAL #

VIPERINDUSTRIAL PRODUCTS

HAMILTON,MI 49419

P.O. BOX 104 VIPER...exceptional

value

MODEL # SL1610SE

CONGRATULATIONS on your purchase of a Viper product,

and welcome tothe V.I.P. family. We appreciate your

business and will do everything in our powerto keep you

happywithyour purchase formanyyears to come.

As part ofthe V.I.P. family, you are entitledtothe best

protection byone of the most comprehensive warranties in the

industry.

Thank-you forpurchasing Viper products!

Tom Vander Bie, CEO

TABLE OF CONTENTS

Machine Components 3

SafetyPrecautions 4

Machine Set Up5

Machine Operation 5-6

Machine Maintenance & Storage 6-7

Troubleshooting8

Parts Lists9-16

Wiring Diagram17

ACHINE COM

ONENTS

1) Vacuum / pump on/off switch

7) Sprayjets

2) Brush circuit breaker

8) Brush assembly

3) Brush / sprayon/off button

9) Pickup head

4) Drain hose

10) Solution tank fill port

5) Accessorytool solution hookup

11) Recoverytank lid

6) Br

ush raise and lower foot pedal

SAFETY PRECAUTIONS

GROUNDING INSTRUCTIONS

General This carped extraction machine

shall be grounded while in use to protect

the operator from electric shock. The

machine is provided witha three-contact

groundingtype attachment plugto fit the

proper groundingtype receptacle. The

green (orgreen &yellow) conductor in the

cord is the groundingwire. Never connect

this wire to other than the groundingpin of

the attachment plug.

This machine is for use on a nominal 120-

volt circuit and has a groundingplugthat

resembles the plugillustrated in figure

below. Make sure that the machine is

connected to an outlet havingthe same

configuration as the plug.No adapter

should be used with this machine.

This machine is intendedfor commercial

use. It is constructed foruse in an indoor

environment and is not intended for any

other use. Use onlyrecommended

accessories.

All operators shall read, understand and

exercise the followingsafetyprecautions:

1) Do not operate machine:

- Unless trained and authorized

- Unless you have read and

understand operators manual

- In flammable or explosive areas.

- With damaged or modified cord or

plug.

- If not in proper operatingcondition.

- In outdoor areas.

- In standingwater.

- Without filters in place.

- With the use of unapproved extension

cords.

2) Before operating machine:

- Make sure all safetydevices are in

place and operate properly.

3) When using machine:

- Mixand handle anychemicals

accordingto manufacturer’s

recommendations

- Do not run machine over cord.

- Do not pull machine bycord or plug.

- Do not pull cord around sharp edges

or corners.

-Do not unplug bypullingonthe cord.

- Do not stretch cord.

- Do not handle plugwith wet hands.

- Keep cord awayfrom heated

surfaces.

- Do not pick up flammable materials

or reactive metals.

- Report machine damage or faulty

operation immediately.

4) Before leaving or servicing machine:

- Turn off machine.

- Unplugpower cord from outlet.

5) When servicing machine:

- Unplugcord from outlet.

- Use manufacturer supplied or

approved replacement parts.

- Avoid movingparts. Don’t wear

loose clothing.

SLIDER EXTRACTOR SETUP

!!! Read operators manual thoroughly

prior to operating or servicing this

machine!!!

Carefullycheck the shippingcarton for

signs of damage. Report anycarton

damage to carrier immediately.

Check carton contents to ensure carton is

complete. Contact your Viper distributor if

anythingis missing.

Contents:

•Carpet Extractor

•Short bleeder”vacuum hose

•50’extension power cable

!!! Read operators manual

thoroughly prior to operating or

servicing this machine!!!

1) Usinga hose or bucket, fill tank with a

maximum of 10 gallons of hot water.

2) Add distributor recommended cleaning

solution

!!! Do not use flammable liquids or

operate machine in or near

flammable liquids or vapors!!!

3) Connect the supplied extension power

cable to the machine. Plugcord into a

grounded wall outlet. (see grounding

instructions)

4) Drop the brush head to the floor with

the foot release pedal on the back of

the machine.

MACHINE OPERATION

PRIOR TO EXTRACTING CARPETS

1) Inspect power cable and extension

cable for damage. Replace cable if

damage is found.

2) Vacuum carpet to remove debris prior

to extractingcarpet.

CARPET EXTRACTING

1) Turn on vacuum / pump switch.

NOTE: Solution will only spray when

the brush / spray button is pushed.

2) To start cleaning, push the brush /

spraybutton and begin topull the

machine backwards.

NOTE: For best cleaning results, pull

back on the machine at apace of

approx. 10 feet in 15 seconds.

3) Release brush / spraybutton at the end

of the path, and continue to pull

machine back for another 12 inches to

pick up excess solution.

4) Tip machine back onto the transport

wheels and push forwardto begin next

path.

OPERATING HINTS

1) Overlap cleaningpath byapprox. 2

inches

2) Work awayfrom power outlet and

power cable in order to avoid damage

to the power cable.

3) Continuallycheck for foam buildup in

recoverytank. Use a distributor

recommended foam control solution.

NOTE: Excessive foam buildup will not

activate the float shut-off and may cause

damage to the vacuum motor.

4) Repeat extraction path on heavily

soiled areas.

5) If brush stops spinning, there maybe

an obstruction in the brush. Unplugthe

power cable, raise the brush off the

floor and check for an obstruction.

Check & reset the brush circuit breaker

located on the control housing.

6) When recover of the dirtysolution ends,

or the solution tank is empty,you must

drain the recoverytank. (see TANK

DRAINING)

USE OF ACCESSORY TOOLS

NOTE: Prior to cleaning upholstery, be

sure to read cleaning instructions provided

by the manufacturer.

1) Disconnect black vacuum hose off the

back right side of the machine.

Connect (optional) accessoryvacuum

hose to area where the standard

vacuum hose was removed.

2) Connect (optional) accessorysolution

hose to brass quick connect coupler

located on the back of the machine.

3) Connect (optional) accessorytool to

solution and vacuum hoses.

4) Turn on vacuum / pump switch.

5) Operate accessorytools as needed.

6) When cleaningis completed, relieve

water pressure from solution lines by

turningoff vacuum / pump switch and

then squeeze trigger for 4seconds.

DRAINING TANKS

DRAINING SOLUTION TANK

1) Disconnect vacuum hose from back of

machine and connect the bleeder”

vacuum hose (included with machine)

to the machine back.

2) Remove the solution tank filter at the

fill area and place end of bleeder”

hose into the bottom of the tank.

3) Turn on vacuum / pump switch &

vacuum out the remainingsolution.

DRAINING RECOVERY TANK

1) Turn off machine, unplugand remove

power cable.

2) Unhook drain hose off the back of the

machine and remove drain hose

stopper.

3) Drain dirtysolution into floor drain.

4) Replace drain hose stopper and

reattach hose to back ofmachine.

MACHINE MAINTENANCE

To keep the machine performingwell

for manyyears, please follow the

followingmaintenance procedures.

!!! Always confirmthat the machine

is unplugged prior to performing

any maintenance or repairs!!!

DAILY MAINTENANCE

1) When cleaningoperation is complete

for the day, drain and rinse the

recoverytank thoroughlywith clean

water.

2) Remove remainingsolution from

solution tank.

3) Remove float shut-off (pingpongball

in cage) from recoverytank and clean

with water.

4) Remove and inspect brass sprayjets. If

necessary, clean jets in acetic acid

solution.

NOTE: Do not clean brass jets with a

pointed object, as it will damage the jets.

5) Check brush assembly& remove any

debris or carpet fibers.

6) Check pick up head and remove any

debris or carpet fibers.

7) Check condition of the stainless steel

pickup shoes on the pickup head. The

shoes must contact the floor for the

whole length of the pickup head.

Replace as necessary.

8) Clean machine with a nonabrasive

cleaner.

9) Inspect power cable for anydamage.

Replace if necessary.

MONTHLY MAINTENANCE

1) Flush pump & plumbingwith an acetic

acid solution to dissolve anychemical

buildup.

MixingInstructions:

a) Premix16 oz. or an acetic acid

solution with 2 gallons of water and

pour into solution tank.

b) Turn vacuum / pump switch on

c) Put machine head over floor

drain and operate machine for 50

seconds.

d) Shut machine down and allow

remainingsolution to sit in

machine overnight.

e) The followingday, sprayout

remainingsolution and flush

system again with 3 gallons of

clean water.

2) Inspect machine for water leaks.

3) Lubricate wheels with a water resistance

lubricant.

4) Check machine for loose or missing

nuts, screw and bolts andreplace as

necessary.

MACHINE STORAGE

1) Prior to storingthe machine, ensure the

solution and recoverytanks are clean

and emptyof anysolution.

2) Store machine in upright position in a

dryarea, with the brush head off the

floor.

3) Remove recoverytank clear lid to

allow for air circulation.

NOTE: If you are storing the machine in

an area which can freeze, be sure both

tanks and the solution plumbing are empty

of all water and dry!

BASIC TROUBLESHOOTING

PROBLEM CAUSESOLUTION

Machine doesn't

work Not plugged in to power sourcePlug into a grounded outlet

Faultypower cableContact Viper Distributor

Faultyextension power cableReplace with newextension power cable

Building circuit breaker trippedReset circuit breaker

Solution pump not

working Vacuum/ pump switch not onTurn on switch

Vacuum/ pump switch faultyContact Viper Distributor

FaultysolenoidContact Viper Distributor

Faultysolution pumpContact Viper Distributor

Pump overheated Determine cause and allow30 minutes for

pump to cool

Loose or broken wiringContact Viper Distributor

Vacuummotor not

working Vacuum/ pump switch not onTurn on switch

Vacuum/ pump switch faultyContact Viper Distributor

Vacuummotor thermal overload tripped

Checkfor obstruction and allow30 minutes

to cool

FaultyvacuummotorContact Viper Distributor

Worn carbon brushesContact Viper Distributor

Loose or broken wiringContact Viper Distributor

Poor pickup Air leaking around clear recoverylidEnsure recoverylid is firmlytightened

Clogged float shut-offRemove float shut-off and clean off debris

Float shut-off is activatedDrain recoverytank

Loose drain hose stopperEnsure stopper is securelyin place

Loose vacuumhose connectionsEnsure vacuumhose connections are tight

Defective vacuumhoseReplace vacuumhose

Loose vacuumhose cuffsEnsure cuffs are secure to the hose

Damaged or loose pickup head shoesContact Viper Distributor

Pulling machine too fastSlowdown cleaning operation

Uneven or no

solution spray Solution tankis emptyor lowFill solution tank

Vacuum/ pump switch not onTurn on switch

Dirtyor plugged spraytipsClean or replace spraytips

Improper spraytip size or sprayangleContact Viper Distributor

Worn spraytipsContact Viper Distributor

Faultysolution pumpContact Viper Distributor

Plugged solution tankfilterClean or replace filter

Pinched or kinked solution hose Checkfor obstructions and kinks and reroute

or replace ifneeded

DIA NO PART

NUMBER DESCRIPTION NO

REQ'D

1VV96001SCLEAR DOME1

2VV60287AGASKET,CLEAR DOME1

3VF13491SCREW RHM M4X12 SST6

4VV67109BEND,TUBE1

5VV67301COUPLER1

6VV67302GASKET,COUPLER1

7VV67108ELBOW1

8VF81226COUPLER VAC HOSE1

9VV67705DRAIN HOSE1

10VV67113-1VAC HOSE1

11VV10113CLAMP,HOSE 2"2

12VV20509SCREW,RHM M5X10 SST4

13VV13601WASHER,LOCK,SST 52

14VV50712CLAMP,CORD3

15VV67503SWITCH1

16VV67509BUTTON,SWITCH1

17VV67504CIRCUIT BREAKER,2A1

18VF14126SCREW,M5X12,HEX3

19GV40215CORD WRAP1

20VV67111CLAMP,DRAIN HOSE1

21VV67501SWITCH HOUSING1

22VF99008STRAIN RELIEF 1

23VV13511 WASHER,TEETH, 32

24VF14212SCREW,M3X252

25VV67507CORD1

26VV67116POWER CORD2

27VV67505BUSHING,CORD,90 1

28VV13652NUT,LOCK,M32

29VV67508BRACKET,SWITCH1

30VV20291 WASHET,LOCK, 42

31VF13491SCREW,M4X122

32VF99023SWITCH ASSY1

33VV67105CONNECTOR1

34GT13032WASHER,PLAIN, 6X 16X1.51

35VV13607WASHER,LOCK,SST 61

36GT13056SCREW,M6X16,PH1

37VV80128BARB,HOSE1

38VV80115 ELBOW,STRECT 45 1

39VV80125ANUT,COUPLING1

40VV20667 WASHER,LOCK,INTERNAL TOOTH 1

PARTS LIST

Andere Handbücher für SL1610SE

Inhaltsverzeichnis

Andere Viper Bodenreinigungsmaschine Handbücher

Viper

Viper VE 13 P Bedienungsanleitung

Viper

Viper AS710R Bedienungsanleitung

Viper

Viper AS6690T-US Bedienungsanleitung

Viper

Viper FANG 20 Bedienungsanleitung

Viper

Viper CEX410 Benutzerhandbuch

Viper

Viper VF1517 Bedienungsanleitung

Viper

Viper AS6690T Benutzerhandbuch

Viper

Viper AS4325B Bedienungsanleitung

Viper

Viper FANG 20 Bedienungsanleitung

Viper

Viper VN1715 Bedienungsanleitung

Viper

Viper CEX410 Bedienungsanleitung

Viper

Viper SCRUBBER FANG 18C Bedienungsanleitung

Viper

Viper AS6690T Benutzerhandbuch

Viper

Viper AS430B Benutzerhandbuch

Viper

Viper VE 17P-EU Bedienungsanleitung

Viper

Viper AS6690T Bedienungsanleitung

Viper

Viper AS4335C Benutzerhandbuch

Viper

Viper AS1050R Bedienungsanleitung

Viper

Viper AS380/15B-EU Bedienungsanleitung

Viper

Viper DR 1500 H Bedienungsanleitung

Viper

Viper VE 17 HS P Bedienungsanleitung

Viper

Viper TP1500 Bedienungsanleitung

Viper

Viper DR1500H-EU Bedienungsanleitung

Viper

Viper Fang 20HD Bedienungsanleitung

Beliebte Bodenreinigungsmaschine Handbücher anderer Marken

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Bedienungsanleitung

Numatic

Numatic ET 4045 Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Bedienungsanleitung

Mytee

Mytee 8070 Mytee-Lite Bedienungsanleitung

Kärcher

Kärcher B 140 R Bedienungsanleitung

Triple S

Triple S Ace 26T1 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SW 750 Bedienungsanleitung

Tornado

Tornado Marathon 2000 98190 Handbuch

Windsor

Windsor ADMIRAL Admiral 8 Bedienungsanleitung

Numatic

Numatic TTB 1117/100 Bedienungsanleitung

Tennant

Tennant 8210D Bedienungsanleitung

Nobles

Nobles Frontier Produkthandbuch

lavina

lavina 21-X Bedienungsanleitung

KENT

KENT Edge 28B Bedienungsanleitung

Tennant

Tennant 215 Produkthandbuch

Windsor

Windsor BDP 51/2000C Bedienungsanleitung

CleanFreak

CleanFreak DURA-18HD Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Administratorhandbuch