Viper AS380/15C-EU Bedienungsanleitung

VF89027C-EU REV:02(2013.6.18)

AS380/15C-UK

User Manual

Original instructions

AS380/15C-EU

ENGLISH USER MANUAL………………………………………………… 1-10

DEUTSCH ETRIE SANLEITUNG……………………………………….. 11-21

FRANÇAİS MODE D'EMPLOI………………………………………………. 22-31

NEDERLANDS GE RUIKSAANWIJZING……………………………………… 32-42

ITALIANO MANUALE D’ISTRUZIONI……………………………………. 43-53

ESPAÑOL USER MANUAL………………………………………………… 54-64

PORTUGUÊS MANUAL DO USUÁRIO……………………………………….. 65-74

ΕΛΛΗΝΙΚΆ ΕΓΧΕΙΡΙ∆ΙΟ ΧΡΗΣΤΗ…………………………………………... 75-85

ČESKÝ UŽIVATELSKÝ MANUÁL…………………………………….... 86-95

POLSKI INSTRUKCJA O SŁUGI……………………………………….. 96-105

MAGYAR FELHASZNÁLÓI KÉZIKÖNYV……………………………….. 106-115

ROMÂNĂ MANUAL DE UTILIZARE…………………………………….. 116-125

РУССКИЙ РУКОВОДСТВО ПОЛЬЗОВАТЕЛЯ…………………………… 126-136

БЪЛГАРСКИ РЪКОВОДСТВО НА ПОТРЕБИТЕЛЯ……………………...… 137-147

Company information:

www.vipercleaning.eu

info-eu@vipercleaning.com

USER MANUAL

SAFETY PRECAUTIONS

This machne is intended for commercial use.It is constructed for use in an indoor environment and is

Not intended for any other use. Use only with recommended accessories.

All operators shall read, understand and exercise the following safety precautions:

1) O NOT OPERATE MACHINE:

Unless trained and authorized.

Unless you have read and understand the operators manual.

In flammable or explosive areas.

If not in proper operating condition.

In outdoor areas.

2) BEFORE OPERATING MACHINE:

Make sure all safety devices are in place and operate properly.

3) WHEN USING MACHINE:

Go slow on inclines and slippery surfaces.

Follow all safety guidelines.

e very careful when using the machine in reverse.

Report and fix any damage to machine prior to operating it.

4) BEFORE LEAVING OR SERVICING MACHINE:

Stop machine on level ground.

Turn machine off.

5) WHEN SERVICING MACHINE:

Read operators manual thoroughly prior to operating or servicing this machine.

Use manufacturer supplied or approved replacement parts.

Secure machine with wheel blocks prior to jacking the machine up.

Use approved jack or hoist to safely elevate the machine.

WHEN SERVICING MACHINE:(con’t)

Disconnect the AC cable.

Avoid contact with corrosive liquids.

Avoid moving parts, Do not wear loose fitting clothing while servicing machine.

WARNING！

！！

！

Flammable materials can cause an explosion or fire. Do not use flammable materials

In tanks.

WARNING！

！！

！

Flammable materials or reactive metals can cause explosion or fire .Do not pick up.

MACHINE SET UP&INSTALLATION

UNCRATING MACHINE

e sure and check packing carton for any damage. Immediately report any damage to carrier.

Check contents of package to ensure that the following items are included:

1. Machine

2. Squeegee assembly

3. Scrubber-dryer User Manual

4. brush or pad driver

（

if equipped

）

MACHINE SET UP

Pre-operation checks

1. Sweep or dust mop the surface to be cleaned.

2. Check that squeegee is properly installed.

3. Lower the squeegee (33) with the lever (26).

4. Ensure that the AC cable is connected to a corresponding voltage power supply.

5. Check that brush/pad is properly installed.

Brush/Pad driver installation and disassembly

NOTE

Only install manually. If auto-installation, it will wear brush hub.

Make sure that the tanks are empty before disassembling the brush.

1. Disconnect the AC cable(16).

2. Lay down the machine in this position as indicated in the figure2, Pull up the lift lever (26) to raise

the squeegee up (33).

3. Mount the brush or pad driver onto the drive wheel hub and then rotate counterclockwise until it

locks, as indicated in the figure 3.

4. To remove the brush/pad, rotate the brush/pad clockwise until it is released from drive wheel hub.

WARNING

Do not turn on the machine in this position as below. The brush/pad could disengage and cause in ury.

Figure 2

USER MANUAL

Squeegee installation

1. Disconnect the AC cable(16).

2. Pull down the squeegee lift lever (26) to put down the squeegee on the “working” position.

3. Lay down the machine in this position as indicated in the figure2.

4. Loosen the two knobs (55) on the squeegee and slide the squeegee into the slots of squeegee

brackets

Tighten the knobs securely (unscrew the knobs, if disassembly).

5. To replace the front/rear squeegee (56/57), unscrew the thumb nut (37).

Solution tank filling

NOTE

The machine can be filled with a with pipe or bucket. Do not remove the Solution filter (21) while

filling.

1. Fill water into solution tank (3) from the inlet (20) through pipe or bucket

2. Do not fill the solution tank completely, leave a few centimeters from the edge.

3. The water temperature must not exceed 40

℃

CAUTION！

Use only low-foam and non-flammable detergents, intended for automatic scrubber applications

Solution tank draining

NOTE

Solution tank should be drained and cleaned after each scrubber operation is

completed.

Figure 3

．

Unscrew the drain cap (22) on the bottom of solution tank. The solution/water will flow

freely into a bucket or floor drain.

．

Rinse the solution tank with clean water after every use. This will help prevent chemical

build up and clogging of the solution lines.

．

Screw up the drain cap (22).

Recovery tank draining

NOTE

Recovery tank should be drained and cleaned after each scrubber operation is

completed.

．

Turn the latch (17) off the recovery tank, take off the recovery tank from machine by

grasping two grooves of tank. Open the lid (1) and overturn the recovery tank to

drain the dirty water into a container, or unscrew the drain cap (22) to let water pipe

out to a bucket.

．

Clean and Rinse the recovery tank with clean water after every use.

．

Re-place the recovery tank on the machine and turn the latch (17) to lock the tank..

MACHINE OPERATION

．

Set the handle to a comfortable height by pressing lever (25).

．

Lower the squeegee (33) onto the floor by pulling down the lift mechanism (26).

．

Ensure that the AC cable is connected to a corresponding voltage power supply.

．

Turn on the brush motor switch (48) and the solution switch (50), the indicator light will be on.

．

Turn on the vacuum motor switch (49), the indicator light will be on.

．

If necessary, adjust the water flow by turn the ball valve (31) manually

．

Pull one or both operating triggers (24), and then brush will start to spin, solution will begin to flow.

Move the machine and start cleaning.

CAUTION！

Before lifting the brush/pad, please disconnect AC cable from outlet (16).

CAUTION！

When cleaning excessively aggressive floors or others this could cause the machine not to

work, the three switches on the control panel may turn off. It means the machine is being

overloaded. Please press the overload protector(29),then turn on all the switches on the

Control panel (47).

AFTER USING THE MACHINE

After scrubbing, please proceed with below actions before leaving the machine:

．

Remove the brush/pad-holder.

．

Empty the tanks as shown in the previous paragraph.

．

Perform the daily maintenance procedures (see the maintenance chapter).

．

Store the machine in a clean and dry place, with the brush/pad-holder and the squeegee

．

If storing in an area which may reach freezing temperatures, be sure to drain all fluids from the

machine prior to storage. any damage caused by freezing temperatures will not be covered by the

warranty.

USER MANUAL

MACHINE NOT BEING USE FOR LONG PERIO S

If the machine is not going to be used for more than 30days, please proceed with below actions:

1. Perform the procedures shown in ‘After Using the Machine paragraph’.

2. Disconnect the AC cable(16).

MAINTENANCE

The lifespan of the machine and its maximum operating safety are ensured by correct and regular

maintenance. The following chart provides the scheduled maintenance. The intervals shown may vary

according to particular working conditions, which will be defined by the person in charge of the

maintenance.

WARNING

Maintenance procedures must be sure the cable unplug from outlet .

Moreover, carefully read the instruction in the Safety chapter.

All scheduled or extraordinary maintenance procedures must be performed by qualified personnel, or by

an authorized Service Center.

This Manual describes only the easier and most common maintenance procedures.

For other maintenance procedures shown in the Scheduled Maintenance Table, refer to the Service

Manual that can be consulted at any Service Center.

SCHE ULE MAINTENANCE TABLE

Procedure Daily, after using

the machine

Weekly Every six

mouths

yearly

Squeegee cleaning

rush cleaning

Tank and vacuum grid with float cleaning, the

cover gasket check

Squeegee blade check and replacement

Solution filter cleaning

Out-water pipe filter cleaning

Screw and nut tightening check (1)

Lubricate rotary parts

(1)

rush/Pad-holder motor carbon brush check or

replacement

(2)

Vacuum system motor carbon brush check or

replacement

(2)

(1) And after the first 8 working hours.

(2) This maintenance procedure must be performed by an authorized viper Service Center.

SQUEEGEE CLEANING

NOTE

The squeegee must be clean and its blades must be in good condition in order to

getting a good drying performance.

CAUTION!

It is advisable to wear protective gloves when cleaning the squeegee because there may be sharp debris.

SQUEEGEE BLA E CHECK AN REPLACEMENT

1. Take off the squeegee as shown in the previous paragraph.

2. Check to see if the edge of the front/rear blades are cracked or split, if necessary replace them with

new.

3. Unscrew six the thumb nut (37) to get off the blades.

4. Check the front/rear blades for integrity, cut and tears. If they are not adequate, overturn or replace

them.

5. Install the squeegee in the reverse order of removal.

BRUSH /PA RIVER CLEANING

CAUTION！

It is advisable to wear protective gloves when cleaning the brush/pad because there may be sharp debris.

1. Remove the brush/pad as shown in the previous paragraph.

2. Clean and wash the brush/pad with water and detergent.

3. Check the brush bristles for integrity and wearing status; if necessary, replace the brush.

4. Check the pad for wearing status; if necessary, replace the pad driver.

TANK/VACUUM GRI WITH FLOAT CLEANING AN COVER

GASKET CHECK

CAUTION！

It is advisable to wear protective gloves when cleaning the tank and vacuum/suction assembly because

there may be sharp debris.

1. Move the machine to the appointed disposal area.

2. Disconnect the AC cable (16).

3. Take off the recovery tank (2), clean and rinse both solution/recovery tank, and drain out.

4. Take off all vacuum kits, gasket, filter, clean and re-install.

5. Check the recovery tank lids gasket ring and the vacuum rubber connector (18) between two tanks

are integrity or not..

NOTE

The gasket ring of recovery tank and the rubber connector between two tanks create

vacuum in the tank. If necessary, replace them.

MACHINE STRUCTURE

1. Recovery tank lid

2. Recovery tank

3. Solution tank

4. rush cover

USER MANUAL

5. umper wheels

6. rush

7. Front handle cover

8. Control panel

9. Rear handle cover

10. Handle sleeve

11. Handle steel tube

12. vacuum assembly

13. Squeegee suction assembly

14. Left gear seat

15. Right gear seat

16. cable

17. Latch

18. Rubber connector

19. Hose joint

20. Inlet

21. Solution filter

22. Drain cap

23. Wheels

24. Left and right trigger

25. Handle lever

26. Squeegee lift lever

27. Squeegee string

28. Electrical ox

29. Overload protector

30. Wheel cover

31. Adjusting valve

32. Solenoid valve

33. Squeegee

34. Squeegee wheels

35. Squeegee hose

36. Axle

37. Thumb nut

38. Vacuum motor

39. rush motor

40. Drive wheel

41. elt

42. Squeegee rotation plate

43. Connecting bracket

44. Squeegee bracket

45. Motor mounting plate

USER MANUAL

Control panel

47. Control panel

48. rush motor switch

49. Vacuum motor switch

50. Solution switch

TECHINICAL ATA

Machine length*width*height 770x500x550MM

Solution tank capacity 15L

Recovery tank capacity 15L

Wheel diameter 254MM

rush motor data 220V-240V 250W

Vacuum motor data 220V-240V 300W

Electromagnetic valve data 220V-240V

Maximum gradient 2%

Sound level 72 d A

Power cable length 15M

Working capacity, up to 800mm H2O

Cleaning productivity 750m2/hour

Squeegee width 490mm

rush diameter 380mm

rush rpm 140rpm

Charger /

Machine weight 39kg

Machine weight(with charger and package) 44kg

Carton spec 780x415x590MM

Andere Handbücher für AS380/15C-EU

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Viper Bodenreinigungsmaschine Handbücher

Viper

Viper AS710R Bedienungsanleitung

Viper

Viper TP1500 Bedienungsanleitung

Viper

Viper AS380/15B-EU Bedienungsanleitung

Viper

Viper AS380/15B-EU Bedienungsanleitung

Viper

Viper VN1715 Bedienungsanleitung

Viper

Viper AS6690T Bedienungsanleitung

Viper

Viper CEX410 Bedienungsanleitung

Viper

Viper SCRUBBER FANG 18C Bedienungsanleitung

Viper

Viper AS380/15B-EU Bedienungsanleitung

Viper

Viper VN1500 Bedienungsanleitung

Viper

Viper AS530R Benutzerhandbuch

Viper

Viper VF1517 Bedienungsanleitung

Viper

Viper AS4325B Bedienungsanleitung

Viper

Viper AS1050R Bedienungsanleitung

Viper

Viper Dragon DR2000DC Dust Control Bedienungsanleitung

Viper

Viper SCRUBBER FANG 18C Bedienungsanleitung

Viper

Viper AS4335C Benutzerhandbuch

Viper

Viper AS430B Benutzerhandbuch

Viper

Viper AS6690T Benutzerhandbuch

Viper

Viper SL1610SE Bedienungsanleitung

Viper

Viper VN20DS Bedienungsanleitung

Viper

Viper SCRUBBER FANG 18C Bedienungsanleitung

Viper

Viper AS6690T-US Bedienungsanleitung

Viper

Viper DR1500H-EU Bedienungsanleitung

Beliebte Bodenreinigungsmaschine Handbücher anderer Marken

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Bedienungsanleitung

Numatic

Numatic ET 4045 Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Bedienungsanleitung

Mytee

Mytee 8070 Mytee-Lite Bedienungsanleitung

Kärcher

Kärcher B 140 R Bedienungsanleitung

Triple S

Triple S Ace 26T1 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SW 750 Bedienungsanleitung

Tornado

Tornado Marathon 2000 98190 Handbuch

Windsor

Windsor ADMIRAL Admiral 8 Bedienungsanleitung

Numatic

Numatic TTB 1117/100 Bedienungsanleitung

Tennant

Tennant 8210D Bedienungsanleitung

Nobles

Nobles Frontier Produkthandbuch

lavina

lavina 21-X Bedienungsanleitung

KENT

KENT Edge 28B Bedienungsanleitung

Tennant

Tennant 215 Produkthandbuch

Windsor

Windsor BDP 51/2000C Bedienungsanleitung

CleanFreak

CleanFreak DURA-18HD Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Administratorhandbuch