Viper BARRACUDA Bedienungsanleitung

VA51063

REV.02(08-07)

VIPER...exceptional

value

www.usviper.com

VIPERNORTHAMERICA

(866)418-4737

P.O. BOX104

HAMILTON, MI49419

(866)41 -VIPER

IMPORTANT: READOWNERSMANUALCAREFULLY

BARRACUDA

SERIAL#

MODEL# CUDA26

Pleasefillout&returnyourwarrantycard!

OWNERSMANUAL

VIPER

DUALMOTORVACUUM

CONGRATULATIONS on your purchase of a Viper product,

and welcome to the V.I.P. family. We appreciate your business

and will do everything in our power to keep you happy with

your purchase for many years to come.

As part of the V.I.P. family, you are entitled to the best protection

by one of the most comprehensive warranties in the industry.

Thank-you for purchasing Viper products!

Tom Vander Bie, CEO

TABLE OF CONTENTS

Safety Precautions 1

Machine Components 2

Machine Operation 3-4

Machine Maintenance & Storage 4

Troubleshooting 5

Parts Breakdown 6

Parts Lists 7-8

Accessories 9

Wiring Diagram 10

SAFETY PRECAUTIONS

GROUNDING INSTRUCTIONS

General – This carpet vacuum shall be

grounded while in use to protect the

operator from electric shock. The machine

is provided with a three-contact grounding

type attachment plug to fit the proper

grounding type receptacle. The green (or

green & yellow) conductor in the cord is

the grounding wire. Never connect this

wire to other than the grounding pin of the

attachment plug.

This machine is for use on a nominal 120-

volt circuit and has a grounding plug that

resembles the plug illustrated in figure

below. Make sure that the machine is

connected to an outlet having the same

configuration as the plug. No adapter

should be used with this machine.

This machine is intended for commercial

use. It is constructed for use in an indoor

environment and is not intended for any

other use. Use only recommended

accessories.

All operators shall read, understand and

exercise the following safety precautions:

1) Do not operate machine:

- Unless trained and authorized

- Unless you have read and

understand operators manual

- In flammable or explosive areas.

- With damaged or modified cord or

plug.

- If not in proper operating condition.

- In outdoor areas.

- In standing water.

- Without bag / filters in place.

- With the use of unapproved extension

cords.

2) Before operating machine:

- Make sure all safety devices are in

place and operate properly.

3) When using machine:

- Do not run machine over cord.

- Do not pull machine by cord or plug.

- Do not pull cord around sharp edges

or corners.

- Do not unplug by pulling on the cord.

- Do not stretch cord.

- Do not handle plug with wet hands.

- Keep cord away from heated

surfaces.

- Do not pick up flammable materials

or reactive metals.

- Report machine damage or faulty

operation immediately.

- Do not allow children to operate

machine.

4) Before leaving or servicing machine:

- Turn off machine.

- Unplug power cord from outlet.

5) When servicing machine:

- Unplug cord from outlet.

- Use manufacturer supplied or

approved replacement parts.

- Avoid moving parts. Do not wear

loose clothing.

1) Handle

2) Power cord

3) Door latch

4) Power switch

5) Attachment tool intake & cord wrap

6) Vacuum hose

7) Brush housing

8) Brush height adjustment

9) Rear wheels

10) Exhaust vent

11) Handle height adjustment

12) Brush circuit breaker (bottom side)

13) Brush assembly (bottom side)

14) Rear door

MACHINE COMPONENTS

1 2 3 4

MACHINE OPERATION

PRIOR TO VACUUMING CARPETS

1) Inspect power cable and extension

cable for damage. Replace cable if

damage is found.

2) Ensure filter bag is properly installed

NOTE: Never operate machine without

filter bag installed. This could cause

damage to the vacuum motor.

3) Set proper height adjustment for carpet

being cleaned.

CARPET VACUUMING

1) Depress foot pedal and lower vacuum

head to floor.

2) Turn on power switch.

3) Operate by using standard vacuuming

procedures.

4) Check bag periodically to see if it is

full. Replace if necessary.

5) To clean under desks or other tight

areas, depress the foot pedal an

additional time to lower the handle

even further.

OPERATING HINTS

1) Overlap cleaning path by approx. 2

inches

2) Work away from power outlet and

power cable in order to avoid damage

to the power cable.

3) Occasionally check the bag for fullness

& replace as necessary.

4) If brush stops spinning, there may be

an obstruction in the brush. Unplug the

power cable, raise the brush off the

floor and check for an obstruction.

Check & reset the brush circuit breaker

located on the bottom of the brush

housing.

USE OF ACCESSORY TOOLS

NOTE: Accessory tools are available as an

option. Kit VA51061 includes: Dusting

brush, crevice tool, 8’ vacuum hose.

1) Machine must be in upright position

whenever using attachment tools.

2) Remove accessory hose plug on the

vacuum intake port on rear of machine.

3) Connect (optional) vacuum hoses to

intake port & connect desired

accessory tool to end of hose.

4) Turn on vacuum switch and operate

tool using normal vacuuming

procedures.

VACUUM BAG INSTALLATION &

REMOVAL

1) Unlock rear door latch, and allow door

to hinge open.

2) Place paper bag / filter into tank

opening.

3) On paper bag / filter, slide rubber

vacuum collar onto vacuum intake

spout.

4) Close rear door and lock into place.

NOTE: Be sure the bag / filter is

properly placed in bag housing to

ensure proper air flow.

5) To remove bag, simply reverse steps 1-

4 above.

6) Do not re-use paper bag / filter. When

full, dispose of it and replace with a

new one.

MACHINE MAINTENANCE

To keep the machine performing well

for many years, please follow the

following maintenance procedures.

!!! Always confirm that the machine

is unplugged prior to performing

any maintenance or repairs!!!

1) Unplug machine as soon as you are

done using it.

NOTE: When unplugging machine, do not

pull cord around sharp edges or corners &

do not unplug by pulling on the cord.

2) Clean outside of machine with a mild

cleaner.

3) Check power cord for any damage. If

any damage is detected, replace the

cord immediately.

4) Check machine for any loose or

missing nuts and bolts and replace as

necessary.

5) Check paper bag / filter for fullness. If

it is full, replace with a new one.

6) Check vacuum motor filter and exhaust

filter for debris and clean as needed.

NOTE: Do not clean filters with water or

a cleaning solution. Clean by tapping of

debris or blowing with air.

7) Inspect brush for strands of carpet and

debris and remove as needed.

8) Inspect brush bristles for wear and

damage. Replace brush as needed.

9) Inspect gaskets and seals for air leaks

and replace as needed.

10)Check vacuum hose for clogs and holes

and replace as needed.

11)Check vacuum motor carbon brushes

every 250 hours. Replace brushes

when they are 3/8” or less in length.

NOTE: Vacuum motor damage caused

by worn brushes is not covered by

warranty.

MACHINE STORAGE

1) Prior to storing the machine, wrap up

power cord, check paper bag / filter for

fullness and replace if necessary.

2) Clean and / or replace filters.

3) Store machine in upright position in a

dry area, with the brush head off the

floor.

PROBLEM CAUSE SOLUTION

Machine does not work Power switch not in "on" position Turn power switch "on"

Power cord not plugged into outlet Plug power cord into outlet

Power cord is faulty Replace with approved power cord

Building circuit breaker tripped Reset circuit breaker

Faulty wiring Contact Viper Distributor

Faulty on / off switch Contact Viper Distributor

Brush does not work Brush circuit breaker tripped Check brush and belt for obstructions and

remove as needed

Reset circuit breaker

Poor brush pickup Incorrect brush height adjustment Adjust brush height

Clogged brush Remove debris from brush

Brush is worn Contact Viper Distributor

Loose brush drive belt Inspect belt and replace as needed

Low suction Vacuum hose clogged Remove vacuum hose and check for

obstructions

Vacuum hose faulty Check vacuum hose for loose cuffs or holes

and replace as needed

Filters clogged Remove vacuum filter and exhaust filter and

clean

Vacuum bag full Check vacuum bag / filter and relplace as

needed

BASIC TROUBLESHOOTING

DIA

NO PART

NUMBER DESCRIPTION NO

REQ'D

1 VA51009 HANDLE HOUSING 1

2 VA51025 BAG,PAPER,DUST,10.5qt. 1

3 VA51007 REAR COVER AND BAG HOLDER 1

4 GT13022 NUT, M5, NYLON INSERT 13

5 VA51034 GASKET,ADAPTER 1

6 VA51008 ELBOW ADAPTER,HOSE 1

7 VA51022 PLUG AND CORD HOOK 1

8 VV20501 SCREW,M5x14 23

9 VA51023-1 HOSE END 2

10 VA51023-2 HOSE, 2" 1

11 VA51029 COVER, EXHAUST FILTER 1

12 VA51030 FILTER,EXHAUST 1

13 VA51028 PLATE,EXHAUST FILTER 1

14 VA51024 LATCH PLATE 1

15 VV13605 SCREW,FLAT, M6x16 2

16 VA51041 NYLON WASHER 4

17 VA51027 AXLE 1

18 VA51059 ECCENTRIC BUSHING 2

19 VV20509 SCREW,M5x10 17

20 VF13520 RETAINING RING,EXTERNAL,φ12 2

21 VF50119 WAVE WASHER, φ12 2

22 VF13602 WASHER,PLAIN,φ12xφ18x1 2

23 VF48202 WHEEL, 5" 2

24 VF13666 WASHER,PLAIN,φ12 2

25 VF44012 SCREW, M5x12.7 2

26 VF13495 SCREW,HEX, M6x16 4

27 VF13614 WASHER,PLAIN,φ64

28 VA51038 SPRING,LATCH 1

29 VF14214 SCREW,M5x8 1

30 VA51039 SHOULDER BOLT,LATCH 1

31 VV67504 CIRCUIT BREAKER 2AMP 1

32 GT13057 SCREW,SELF-TAPPING, ST5x10 14

33 VA51002 BUMPER,26" 1

34 VF99926-1 RECTIFIER 1

35 VA51065 BLOCK,BRUSH SHAFT,LEFT 1

36 ZD57000 MOTOR,BRUSH,115V 1

37 VA51011 MOUNT PLATE,MOTOR 1

38 VA51019 PULLEY,MOTOR 1

39 VA51021 DRIVE BELT 1

40 VF14254 SCREW,HOLDING, M5x8 1

PARTS LIST

DIA

NO PART

NUMBER DESCRIPTION NO

REQ'D

PARTS LIST

41 VA51018 PULLEY,BRUSH 1

42 VA51015 BEARING 2

43 VA51035 KNOB,ROLLER ADJUST 1

44 VF13508 SCREW,HOLDING, M4x8 1

45 VA51037 SPRING,ROLLER ADJUST 1

46 VA51036 LOCK PIN,ROLLER ADJUST 1

47 VA51042 ROLLER,1.5" 2

48 VA51013 CLAMP,ROLLER BRACKET 4

49 VA51043 AXLE,ROLLER 2

50 VA14001 RETAINING RING,EXTERNAL,φ10 4

51 VA51014 ROLLER BRACKET 1

52 VA51004 BOTTOM SHOE PLATE,26" 1

53 VA51005 BRUSH,26" 1

54 VA51047 BRACKET,RECTIFIER 1

55 VA51003 BRUSH HOUSING,26" 1

56 VA51006 SHAFT,BRUSH,26" 1

57 VA51017 STRING GUARD,BRUSH 1

58 VA51016 BLOCK,BRUSH SHAFT,RIGHT 1

59 VV20502 SCREW,FLAT, M5X16 2

60 VA51048 LABEL, "BARRACUDA" 1

61 VA51001 BASE HOUSING,26" 1

62 VA51010 LATCH,HANDLE 1

63 VA13476 SCREW,M5x40 1

64 VA51040 SHULDER BOLT,PIVOT 2

65 VA51052 LABEL 1

66 VA51012 TUBE,BASE HOUSING 1

67 VV13635 SCREW,M5x20 4

68 VA51032 RETAINER RING,VACUUM MOTOR 1

69 VA51033 GASKET,VACUUM MOTOR 1

70 VA41036 VACUUM MOTOR,115V 1

71 VA51049 FILTER,VACUUM MOTOR 1

72 VF82082 LOGO, "VIPER" 1

73 VA65001 POWER CORD,14/3C, SJTW, 50FT 1

74 VA51044 STRAIN RELIEF,CORD 1

75 VF83109 CATCH 1

76 VV13650 SCREW,M4x10 6

77 VA51026 PLATE,SWITCH 1

78 VF91346 SWITCH,ROCKER 1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Viper Staubsauger Handbücher

Viper

Viper GV25 Bedienungsanleitung

Viper

Viper DSU8 Bedienungsanleitung

Viper

Viper MB39CV Mamba Series Bedienungsanleitung

Viper

Viper SD 18 Bedienungsanleitung

Viper

Viper SHOVELNOSE SN18WD Bedienungsanleitung

Viper

Viper GVD10-EU Bedienungsanleitung

Viper

Viper CAR275 Bedienungsanleitung

Viper

Viper CAR275 Bedienungsanleitung

Viper

Viper LSU135 Bedienungsanleitung

Viper

Viper CAR275 Bedienungsanleitung

Viper

Viper Rocket TS13 II HEPA Bedienungsanleitung

Viper

Viper WOLF130 Bedienungsanleitung

Viper

Viper SN18WD-U Bedienungsanleitung

Viper

Viper GV35-EU Bedienungsanleitung

Viper

Viper CAR275 Bedienungsanleitung

Viper

Viper GTR1500-EU Bedienungsanleitung

Viper

Viper TP20WD Bedienungsanleitung

Viper

Viper AS4325B Bedienungsanleitung

Viper

Viper 75L Bedienungsanleitung

Viper

Viper Shovelnose Bedienungsanleitung

Viper

Viper SL1610SE Bedienungsanleitung

Viper

Viper FANG 20-EU Bedienungsanleitung

Viper

Viper GV35 Bedienungsanleitung

Viper

Viper MAMBA Series Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch