Vision Fitness R40 Bedienungsanleitung

U40

U20

Read the BIKE GUIDE before using this OWNER’S MANUAL.

EXERCISE BIKE OWNER’S MANUAL

R40

R20

IMPORTANT PRECAUTIONS

SAVE THESE INSTRUCTIONS

When using an exercise product, basic precautions should always be followed, including the following: Read all instructions before

using this exercise bike. It is the responsibility of the owner to ensure that all users of this exercise bike are adequately informed

of all warnings and precautions. If you have any questions after reading this OWNER’S MANUAL, contact your authorized Vision

Fitness retailer.

This bike is intended for in-home use only. Do not use this bike in any commercial, rental, school or institutional setting. Failure to

comply will void the warranty.

READ AND SAVE ALL INSTRUCTIONS BEFORE ASSEMBLING OR USING THIS

EXERCISE BIKE. IT IS STRONGLY RECOMMENDED TO TAKE THE FOLLOWING SAFETY

INSTRUCTIONS.

• CAUTION: If you experience chest pains, nausea, dizziness or shortness of breath, stop exercising immediately and consult your

physician before continuing.

• Use this exercise bike for its intended purpose as described in this manual. Do not use attachments that have not been

recommended by the manufacturer.

• Never operate the exercise bike if it is not working properly or if it has been damaged. Please reference contact information on the

back cover for assistance.

• Do not use the exercise bike without proper footwear. NEVER operate the exercise bike with bare feet.

• Do not wear any clothing that might catch on any moving parts of this exercise bike.

• Keep hands and feet clear at all times from moving parts to avoid injury. Never turn the pedal cranks by hand.

• Do not dismount the exercise bike until the pedals are at a complete STOP.

• Do not attempt to ride the exercise bike in a standing position at high RPMs until you have practiced at slower speeds.

• Do not insert any object, hands or feet into any openings, or expose hands, arms or feet to the drive mechanism or other

potentially moving part of the exercise bike.

• Do not use any equipment that is damaged or has worn or broken parts. Use only replacement parts supplied by an authorized

service technician.

• Do not operate where aerosol (spray) products are being used or when oxygen is being administered.

• Close supervision is necessary when used near children, invalids or disabled people.

• When the exercise bike is in use, young children and pets should be kept at least 3 meters / 310 cm (10 feet) away.

• Ensure that adjustment levers (seat and handlebar fore-and-aft) are properly secured and do not interfere with range of motion

during exercise.

ASSEMBLY

There are several areas during the assembly process when special attention must be paid. It is very important to follow the

assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed

correctly, the bike could have frame parts that are not tightened and will seem loose and may cause irritating noises. To prevent

damage to the bike, the assembly instructions must be reviewed and corrective actions should be taken.

Before proceeding, find your bike’s serial number located on a white barcode sticker on

the bottom-front of the bike as shown in this image.

ENTER YOUR SERIAL NUMBER AND MODEL NAME IN THE BOXES BELOW:

WARNING

SERIAL NUMBER LOCATION

SERIAL NUMBER:

MODEL NAME: VISION BIKE

WARNING

6 7

U20

CR AN K

WATE R B OTTLE HO LD ER

(BOTTLE NOT INCLUDED)

PULSE GRIP HANDLEBARS

RE AR STABILIZER TUBE

POWE R CORD SOCKET

CONSOLE

SE AT P OS T TUBE

SE AT H EI GHT ADJUSTMENT KN OB

FRONT STABILIZER TUBE

SE AT

PE DALS

BIKE FR AME

CONSOLE MA ST

CONSOLE MA ST GR OM ME T

Consult a physician prior to

using any exercise equipment.

Possibility of serious injury if

equipment is used improperly.

Heart rate monitoring systems

may be inaccurate. Over

exercise may result in serious

injury or death. Stop exercising

if you feel pain, faint, dizzy or

short of breath. Read Owner’s

Manual before using. Keep

children off and away from this

equipment. This machine is

designed for Home-use only, do

not use for club or therapeutic

purposes.

Konsultieren Sie einen Arzt,

bevor Sie mit dem Training

beginnen. Bei unsachgemäßem

Gebrauch kann es zu

ernsthaften Verletzungen

kommen.

Herzfrequenzüberwachungssys-

teme können ungenau sein.

Übermäßiges Training kann zu

ernsthaften Verletzungen oder

zum Tod führen. Beenden Sie

Ihr Training, wenn Sie

Schmerzen, Übelkeit, Schindel

oder Atemnot verspüren. Lesen

Sie vor der Erstbenutzung die

Bedienungsanleitung. Halten

Sie Kinder vom Trainingsgerät

fern. Nur für den Heimgebrauch.

WARNING

CR AN K

WATE R B OTTLE HO LDER

(BOTTLE NOT INCLUDED)

PULSE GRIP HANDLEBARS

RE AR STABILIZER TUBE

POWE R CORD SOCKET

CONSOLE

SE AT P OST TUBE

SE AT H EI GHT ADJUSTMENT KNOB

FRONT STABILIZER TUBE

SE AT

PE DALS

BIKE FR AME

CONSOLE MA ST

CONSOLE MA ST GR OMME T

Consult a physician prior to

using any exercise equipment.

Possibility of serious injury if

equipment is used improperly.

Heart rate monitoring systems

may be inaccurate. Over

exercise may result in serious

injury or death. Stop exercising

if you feel pain, faint, dizzy or

short of breath. Read Owner’s

Manual before using. Keep

children off and away from this

equipment. This machine is

designed for Home-use only, do

not use for club or therapeutic

purposes.

Konsultieren Sie einen Arzt,

bevor Sie mit dem Training

beginnen. Bei unsachgemäßem

Gebrauch kann es zu

ernsthaften Verletzungen

kommen.

Herzfrequenzüberwachungssys-

teme können ungenau sein.

Übermäßiges Training kann zu

ernsthaften Verletzungen oder

zum Tod führen. Beenden Sie

Ihr Training, wenn Sie

Schmerzen, Übelkeit, Schindel

oder Atemnot verspüren. Lesen

Sie vor der Erstbenutzung die

Bedienungsanleitung. Halten

Sie Kinder vom Trainingsgerät

fern. Nur für den Heimgebrauch.

WARNING

U40

8 9

R20

CR AN K

WATE R B OTTLE HO LD ER

(BOTTLE NOT INCLUDED)

PULSE GRIP HANDLEBARS

REAR STABILIZE R TUBE

CONSOLE MA ST HANDLEBARS

POWE R CORD SOCKET

CONSOLE

SE AT P OSITION ADJUSTMENT LEVER

FRONT STABILIZER TUBE

ME SH SE ATBACK

SE AT BASE

PE DALS

CONSOLE MA ST

CONSOLE MA ST GR OM ME T

Consult a physician prior to

using any exercise equipment.

Possibility of serious injury if

equipment is used improperly.

Heart rate monitoring systems

may be inaccurate. Over

exercise may result in serious

injury or death. Stop exercising

if you feel pain, faint, dizzy or

short of breath. Read Owner’s

Manual before using. Keep

children off and away from this

equipment. This machine is

designed for Home-use only, do

not use for club or therapeutic

purposes.

Konsultieren Sie einen Arzt,

bevor Sie mit dem Training

beginnen. Bei unsachgemäßem

Gebrauch kann es zu

ernsthaften Verletzungen

kommen.

Herzfrequenzüberwachungssys-

teme können ungenau sein.

Übermäßiges Training kann zu

ernsthaften Verletzungen oder

zum Tod führen. Beenden Sie

Ihr Training, wenn Sie

Schmerzen, Übelkeit, Schindel

oder Atemnot verspüren. Lesen

Sie vor der Erstbenutzung die

Bedienungsanleitung. Halten

Sie Kinder vom Trainingsgerät

fern. Nur für den Heimgebrauch.

WARNING

CR AN K

WATE R B OTTLE HO LD ER

(BOTTLE NOT INCLUDED)

PULSE GRIP HANDLEBARS

REAR STABILIZE R TUBE

CONSOLE MA ST HANDLEBARS

POWE R CORD SOCKET

CONSOLE

SE AT P OSITION ADJUSTMENT LEVER

FRONT STABILIZER TUBE

ME SH SE ATBACK

SE AT BASE

PE DALS

CONSOLE MA ST

CONSOLE MA ST GR OM ME T

Consult a physician prior to

using any exercise equipment.

Possibility of serious injury if

equipment is used improperly.

Heart rate monitoring systems

may be inaccurate. Over

exercise may result in serious

injury or death. Stop exercising

if you feel pain, faint, dizzy or

short of breath. Read Owner’s

Manual before using. Keep

children off and away from this

equipment. This machine is

designed for Home-use only, do

not use for club or therapeutic

purposes.

Konsultieren Sie einen Arzt,

bevor Sie mit dem Training

beginnen. Bei unsachgemäßem

Gebrauch kann es zu

ernsthaften Verletzungen

kommen.

Herzfrequenzüberwachungssys-

teme können ungenau sein.

Übermäßiges Training kann zu

ernsthaften Verletzungen oder

zum Tod führen. Beenden Sie

Ihr Training, wenn Sie

Schmerzen, Übelkeit, Schindel

oder Atemnot verspüren. Lesen

Sie vor der Erstbenutzung die

Bedienungsanleitung. Halten

Sie Kinder vom Trainingsgerät

fern. Nur für den Heimgebrauch.

WARNING

R40

10 11

TOOLS INCLUDED:

F15/17 mm Flat Wrench

F4 mm L Wrench (U20/R20/R40)

F5 mm T Wrench

FScrewdriver

F5 mm L Wrench

F14/17 mm Flat Wrench (U20/U40)

UNPACKING

Unpack the product where you will be using it. Place

the carton on a level flat surface. It is recommended

that you place a protective covering on your floor.

Never open box when it is on its side.

NOTE: During each assembly step, ensure that ALL

nuts and bolts are in place and partially threaded in

before completely tightening any ONE bolt.

NOTE: A light application of grease may aid in the

installation of hardware. Any grease, such as lithium

bike grease is recommended.

NOTE: It is recommended that two people work

together for ease and efficiency while assembling.

PRE-ASSEMBLY

NEED HELP?

If you have questions or if there

are any missing parts, contact your

authorized Vision Fitness retailer.

U20 & U40 PARTS

INCLUDED:

F1 Bike Frame

F1 Rear Stabilizer Tube

F1 Front Stabilizer Tube (U20 only)

F1 Console Mast

F1 Console Mast Grommet

F1 Pulse Grip Handlebar

F1 Water Bottle Holder

F1 Seat Post Tube

F1 Seat

F1 Seat Adjustment Knob

F2 Pedals with Straps

F1 Power Cord

F1 Hardware Kit

R20 & R40 PARTS

INCLUDED:

F1 Bike Frame

F1 Rear Stabilizer Tube

F1 Seat Bottom

F1 Seat Bottom Support (R40 only)

F1 Mesh Seatback

F1 Seat Handlebar

F1 Seat Frame

F1 Set Inside/Outside Seatback

Covers (R20 only)

F1 Console Mast

F1 Console Mast Grommet

F1 Console Handlebar

F1 Water Bottle Holder

F2 Pedals with Straps

F1 Power Cord

F1 Hardware Kit

ALL

MODELS

ASSEMBLY

U20 & U40 PAGE 12 R20 & R40 PAGE 17

12 13

A Open hardware for step 2.

B Slide console mast grommet from the bottom

up the console mast.

C Attach lead wire to console cable and pull

through console mast. Slide console mast

into bike frame.

D U20 ONLY: Attach the console mast to the

bike frame using 6 bolts (g), 6 spring

washers (e) and 1 set screw (h).

E U40 ONLY: Attach the console mast to the

bike frame using 5 bolts (g) and 4 spring

washers (e).

F Slide console mast grommet down over

bike frame.

U20

U40

U20

U40

U20 & U40 ASSEMBLY STEP 2U20 & U40 ASSEMBLY STEP 1

A Open hardware for step 1.

B Attach the rear stabilizer tube to the bike

frame using 2 bolts (a) , 2 bolts (b) and 4

spring washers (c).

C U20 ONLY: Attach the front stabilizer tube

to the bike frame using 2 bolts (d), 2 spring

washers (e) and 2 arc washers (f).

BOLT (B)

70 mm

Qty: 2

SPRING

WASHER (C)

15.4 mm

Qty: 4

BOLT (A)

25 mm

Qty: 2

SPRING

WASHER (E)

13.5 mm

Qty: 2

ARC

WASHER (F)

18 mm

Qty: 2

BOLT (D)

20 mm

Qty: 2

HARDWARE FOR STEP 1 :

REAR STABILIZE R TUBE

SPRI NG WASHERS (C)

BOLTS (A)

BIKE FRAM E

BOLTS (B)

REAR STABILIZE R TUBE

SPRI NG WASHER (E)

ARC WASHER (F)

BOLT (D)

U20 & U40 MODELS

REAR STABILIZE R TUBE

SPRI NG WASHERS (C)

BOLTS (A)

BIKE FRAM E

BOLTS (B)

REAR STABILIZE R TUBE

SPRI NG WASHER (E)

ARC WASHER (F)

BOLT (D)

U20 ONLY

NOTE: Be careful not to pinch any wires

while attaching the console mast.

BOLTS (G)

CONSOLE CABLE

CONSOLE MAST BOOT

CONSOLE MAST

LEAD WIRE

SET SCREW (H)

SPRI NG WASHERS (E)

BIKE FRAME

U20 SHOWNU20 ONLY:

SPRING

WASHER (E)

13.5 mm

Qty: 4

BOLT (G)

15 mm

Qty: 5

SPRING

WASHER (E)

13.5 mm

Qty: 6

SET SCREW (H)

10 mm

Qty: 1

BOLT (G)

15 mm

Qty: 6

HARDWARE FOR U20: HARDWARE FOR U40:

BOLTS (G)

CONSOLE CABLE

CONSOLE MAST BOOT

CONSOLE MAST

LEAD WIRE

BOLT (G)

SPRI NG WASHERS (E)

BIKE FRAME

U40 SHOWN

14 15

U20

U40

U20 & U40 ASSEMBLY STEP 3

A Open hardware for step 3.

B Feed the handlebar wires through the

hole in the console mast and out the top

of the console mast.

C Attach the handlebars to the console

mast using 2 bolts (d) and 2 spring

washers (e).

D Attach the water bottle holder to the

console mast using 2 pre-installed

bolts.

SPRING

WASHER (E)

13.5 mm

Qty: 2

BOLT (D)

20 mm

Qty: 2

HARDWARE FOR STEP 3 :

CONSOLE MAST

HANDLE BARS

SPRI NG

WASHER S (E)

BOLTS (D)

WATE R BOTTLE HOLDER

PRE-IN STALLE D BOLTS

CONSOLE CABLES

U20 SHOWN

NOTE: Be careful not to pinch any wires

while attaching the handlebars.

CONSOLE MAST

HANDLE BARS

SPRI NG

WASHER S (E)

BOLTS (D)

CONSOLE CABLES

WATE R BOTTLE HOLDER

PRE-IN STALLE D BOLTS

U40 SHOWN

U20

U40

U20 & U40 ASSEMBLY STEP 4

NOTE: There is no hardware for this step.

A Attach seat to seat post tube using seat clamp

on bottom of seat, tightening it with the provided

14mm/17mm flat wrench.

B Pull the seat height adjustment knob outward

while sliding the seat post tube into the bike

frame. (NOTE: It may be necessary to turn the seat

adjustment knob to the left to allow the seat

post tube to slide into the bike frame.) Secure by

turning seat adjustment knob to the right.

C Attach the pedal strap to the right pedal.

Attach the right pedal to the right crank

arm, tightening it clockwise with the provided

15mm/17mm flat wrench.

D Attach the pedal strap to the left pedal.

Attach the left pedal onto the left crank arm,

tightening it counter-clockwise with the provided

15mm/17mm flat wrench. (NOTE: The left crank arm

is reverse-threaded, so it is very important that it is

tightened counter-clockwise. Tightening it the opposite

way can damage the pedal or the crank arm or both.)

RIGHT CRAN K ARM

LEFT CRANK AR M

LEFT PEDAL

SEAT POST TUBE

SEAT

RIGHT PE DAL

U40 SHOWN

16 17

U20 & U40 ASSEMBLY STEP 5

NOTE: All hardware is pre-installed.

A Connect the console cables and carefully tuck the

console cables into the console mast.

B Attach the console to the console mast using the 4 pre-

installed bolts.

C Plug in power adapter as shown.

POWER ADAPTER

CONSOLE MAST

PRE-IN STALLED BOLTS

CONSOLE CABLES

CONSOLE

U40 SHOWN

U20

U40

NOTE: Be careful not to pinch any wires while attaching the console.

u20 & u40 assemblY complete!

R20 & R40 ASSEMBLY STEP 1

A Open hardware for step 1.

B Attach the rear stabilizer tube to the

bike frame using 2 bolts (a) and 2 spring

washers (c) to the outside holes and with 2

bolts (b) and 2 spring washers (c) to the

inside holes.

BOLTS (A)

SPRI NG WASHERS (C)

BIKE FRAME

BOLTS (B)

R40 SHOWN

R20

R40

SPRING

WASHER (C)

15.4 mm

Qty: 4

BOLT (A)

20 mm

Qty: 2

BOLT (B)

65 mm

Qty: 2

SPRING

WASHER (C)

15.4 mm

Qty: 4

BOLT (A)

25 mm

Qty: 2

BOLT (B)

70 mm

Qty: 2

HARDWARE FOR R20: HARDWARE FOR R40:

18 19

R20

R40 ASSEMBLY STEP 2

A Open hardware for step 2.

B Remove the pre-installed bolt from the front hole

in the seat rail adjustment lever. Rotate the seat

lever into alignment on the bracket. Reinsert the pre-

installed bolt and tighten both bolts.

C Connect the seat handlebar heart rate wires to

the seat frame heart rate wires. Attach the seat

handlebars to the seat frame with 2 bolts (d) and

2 spring washers (c) to the rear set of holes.

D Set the seat bottom support onto the main seat

frame so that the rear set of holes line up over the front

set of holes on the seat handlebar. Secure in place

with 4 bolts (e) and 4 spring washers (f).

E Attach the seat bottom cushion to the seat

bottom support with 4 bolts (d) and 4 spring

washers (f).

F Slide the seat tilt adjustment lever in place over

the seat frame, making sure the handle of the seat

tilt adjustment lever is pointing up. Tighten the two

set screws in the seat tilt adjustment lever

bracket.

G Attach the mesh seatback to the seat frame using

6 bolts (g).

BOLT (E)

55 mm

Qty: 4

SPRI NG

WASHER (C)

15.4 mm

Qty: 6

BOLT (D)

20 mm

Qty: 6

BOLT (G)

12 mm

Qty: 6

SPRI NG

WASHER (F)

12.2 mm

Qty: 4

HARDWARE FOR STEP 2 :

SEAT RAIL

ADJUSTME NT LEVER

BOLT (G)

PRE-IN STALLE D BOLT

SEAT BOTTOM SUPPORT

SEAT BOTTOM

BOLTS (E)

SPRI NG WASHERS (F)

HANDLE BAR WIRES

SPRI NG WASHERS (C)

BOLTS (D)

BOLTS (G)

MES H SEATBACK

SEAT FRAME

BOLTS (G)

SEAT HANDLEBARS

SEAT TILT ADJ USTMENT LEVE R

PRE-IN STALLE D SET SCREWS

R40

R20 ASSEMBLY STEP 2

A Open hardware for step 2.

B Mount the seat handlebars to the seat

frame with 4 bolts (d) and 4 spring

washers (c).

C Mount the seat bottom to the seat frame with

4 bolts (e) and 4 arc washers (f).

D Place the inside cover over the mesh

seatback and mount the mesh seatback to

the seat frame with 4 bolts (a) and 4 spring

washers (c).

E Attach the outside cover to the seat frame

and inside cover with 3 screws (g).

F Push the seat frame lock lever forward and

side the seat frame onto the seat rail from the

rear of the bike.

G Connect the heart rate wires in the seat

handlebars to the heart rate wires coming

up from the seat rail (fig.a).

H Attach the seat rail stopper (fig.a) to the

seat rail with 2 bolts (a).

BOLT (E)

35 mm

Qty: 4

SPRI NG

WASHER (C)

15.4 mm

Qty: 8

BOLT (D)

15 mm

Qty: 4

BOLT (A)

20 mm

Qty: 6

SCREW (G)

20 mm

Qty: 3

ARC

WASHER (F)

18 mm

Qty: 4

SEAT RAIL

STOPPER

Qty: 1

HARDWARE FOR STEP 2 :

BOLTS (D)

SPRI NG WASHERS (C)

HEART RATE WIRES

MES H SEATBACK

INS IDE COVER

SEAT FRAME

SCREWS (G)

BOLTS (A)

SPRI NG WASHERS (C)

OUTSID E COVER

SEAT BOTTOM

SEAT HANDLEBARS

ARC WASHER S (F)

BOLTS (E)

SEAT RAIL

BOLTS (A)

SEAT RAIL

STOPPER

SEAT RAIL

HEART RATE WIRES

FIG. A

SEAT FRAME LOCK LEVER

Andere Handbücher für R40

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Vision Fitness Heimtrainer Handbücher

Vision Fitness

Vision Fitness Fitness Cycle E3100 Bedienungsanleitung

Vision Fitness

Vision Fitness E1500 Frame 9 Bedienungsanleitung

Vision Fitness

Vision Fitness R70 Bedienungsanleitung

Vision Fitness

Vision Fitness U70-02 Bedienungsanleitung

Vision Fitness

Vision Fitness ES600 Bedienungsanleitung

Vision Fitness

Vision Fitness SIMPLE Bedienungsanleitung

Vision Fitness

Vision Fitness R2200 Bedienungsanleitung

Vision Fitness

Vision Fitness V-SERIES Bedienungsanleitung

Vision Fitness

Vision Fitness R2050 Bedienungsanleitung

Vision Fitness

Vision Fitness E3600HRT Bedienungsanleitung

Vision Fitness

Vision Fitness R2600HRT Bedienungsanleitung

Vision Fitness

Vision Fitness R10 Bedienungsanleitung

Vision Fitness

Vision Fitness R2600HRT Bedienungsanleitung

Vision Fitness

Vision Fitness E3600HRC Bedienungsanleitung

Vision Fitness

Vision Fitness E4000 Bedienungsanleitung

Vision Fitness

Vision Fitness R2700HRT Bedienungsanleitung

Vision Fitness

Vision Fitness R70 Bedienungsanleitung

Vision Fitness

Vision Fitness R2000 Bedienungsanleitung

Vision Fitness

Vision Fitness R2200 Bedienungsanleitung

Vision Fitness

Vision Fitness E3600HRC Bedienungsanleitung

Vision Fitness

Vision Fitness E4000 Bedienungsanleitung

Vision Fitness

Vision Fitness R40 Bedienungsanleitung

Vision Fitness

Vision Fitness U70 Bedienungsanleitung

Vision Fitness

Vision Fitness R1400 Bedienungsanleitung

Beliebte Heimtrainer Handbücher anderer Marken

TOORX

TOORX BRX85 Bedienungsanleitung

Matrix

Matrix KranKcycle Bedienungsanleitung

Weslo

Weslo Vector 302 Kurzanleitung

Matrix

Matrix IC3 Bedienungsanleitung

Sunny Health & Fitness

Sunny Health & Fitness SF-B121021 Bedienungsanleitung

Monark

Monark 827E Bedienungsanleitung

Stamina

Stamina 1310 Bedienungsanleitung

American Fitness

American Fitness SPR-BK1072A Bedienungsanleitung

Cateye

Cateye CS-1000 (CYCLO SIMULATOR) Bedienungsanleitung

BH FITNESS

BH FITNESS H9158H Bedienerhandbuch

Body Sculpture

Body Sculpture BC-7220G Bedienungsanleitung

Cateye

Cateye EC-2300 Bedienungsanleitung

FYTTER

FYTTER RACER RC MSR Bedienungsanleitung

Kikos

Kikos HM-9090M Bedienungsanleitung

Fuel Fitness

Fuel Fitness SU135-40 Bedienungsanleitung

NordicTrack

NordicTrack Gxr 4.2 Bike Bedienungsanleitung

Stamina

Stamina 15-0340A Bedienungsanleitung

KIDSFIT

KIDSFIT Cardio Kids 661 Bedienungsanleitung