Vitek VT-TPTZ25HRAN-8PNL Bedienungsanleitung

VITEK

VT-TPTZ25HRAN-8PNL

Transcendent Gen. IV

8 MegaPixel [4K] 25×

IP PTZ with A.I.

QUICK START GUIDE

FEATURES

• 1/2.8” Sony STARVIS®* 8 MegaPixel [4K] Progressive Scan CMOS STARLIGHT Sensor

•Up to 8 MegaPixel (3840 × 2160) Max Resolution @ 30fps

•Ultra High-Speed Pan / Tilt / Zoom with 25× Optical Zoom Lens (4.8-120mm Focal

Length)

•3.6s Zoom Speed (Optical, Wide-Tele), F1.65~F3.8 Aperture Range

•Smart IR with up to 492’ (150m) IR Range

•Smart H.265+/H.265/H.264+/H.264/MJPEG Compression

•Real-Time Auto Zoom Tracking: Transcendent Gen. IV IP PTZ Cameras Feature the Most

Advanced PTZ Auto-Tracking Available, Powered by A.I.

•Gen. IV Advanced Analytics: Intrusion Detection, Line Crossing, Region Entrance / Exit,

Target Counting [All by Human / Vehicle Classification] Scene Change, Face Detection /

Capture

•Backlight / Highlight Compensation, Auto-White Balance, Gain Control, Day / Night

•True 120dB WDR (Wide Dynamic Range)

•360 Presets, 8 Cruises, up to 16 Presets / Cruise + 4 Tracks (3+ Min. Recording / Track)

•1 Ch. Audio In + Out**, 1 Ch. Alarm In + Out

• Advanced Starlight Technology

•True Day/Night with ICR Cut Filter with Auto/Manual Gain Control

•360° Endless Pan Range, Configurable Speed: .1~200°/s + 240°/s Preset

•Built-in MicroSD Card Slot, Supporting Local Recording up to 256GB

•IP66 Ingress Protection + IK10 [Excluding Glass] Impact Rating

•12VDC Power or PoE+ (802.3.at, class 3)

*12VDC 3Amps Power Supply Included, **PoE Injector Required for PoE Power: VT-POE60 / VT-POE95 [see pg. 13]

•Reset Button, Heater, Fan, Water Removal with Quick Spinning

•1 RJ45 10M/100M Adaptive Ethernet (Supports PoE 802.3.at)

•Wall Mount, Pendant Mount, Semi-Flush Mount, Corner Mount Adapter and

Pole Mount Adapter Sold Separately [see pg. 13]

•3-Year Warranty

* SONY™ is an independent and wholly owned corporation

** Please research local, state and federal laws regarding the implementation of audio surveillance

PLEASE NOTE:

Complete User Guide, Software, Tools, and Updates are

available online. Scan the QR Code or visit:

http://www.vitekcctv.com/Downloads

*Shown with wall mount

VT-TPT23HR-WM

[SOLD SEPARATELY]

2 3

Cable Connections

Overview

First connect the Weather Resistant Cap to an Ethernet patch cable, then connect

cameras’ ethernet adaptor. If not powering the camera with PoE+, also connect the

power cable to an approved 12VDC Power Supply.

Weather Resistant Network Coupler

1. Loosen the nut from the Weather Resistant Network Coupler.

2. Run ethernet cable through coupler, then attach a RJ-45 connector.

3. Tighten the nut and coupler for a weather resistant seal.

1. LAN

2. HP Audio Out

3. MIC In

4. Alarm In / Alarm Out

5. Power

6. Grounding Wire

7. Safety Cable

Installation

Alarm Connections

Before beginning, make sure that the wall or ceiling is strong enough to

1. Alarm Input

a) There is one independent alarm input

port (ALM-IN1), and one grounding port (ALM-GND).

b) Alarm input (NO type): Connect DC5V~DC12V voltage between

the alarm input port (ALM-IN1) and the grounding port (ALM-GND).

c) Alarm input (NC type): DIsconnect the voltage between the alarm input port

(ALM-IN1) and the grounding port (ALM-GND)

2. Alarm Output

a) Supports 1CH alarm output including OPEN, COM connections.

b) Alarm output: One passive switch for a user to connect alarm devices:

the alarm output state will be on / off according to your users’ setting.

withstand the weight of the camera, and that the power is off.*Wall mounting

instructions are below, followed by ceiling mounting and semi-ush mounting.

MicroSD Card

Installation

1. Loosen the cover’s 4 screws

and remove it.

2. Insert a microSD card as

indicated (right) and re-install

the cover.

Insert a

MicroSD

4 5

1. Install the ceiling mount according to the following diagram:

3. Attach the bracket

to the wall with four

screws.

4.Hook the safety wire to the bracket.

Then connect the cables. After that,

attach the speed dome to the bracket

with the screws.

Installation Using Wall Mount VT-TPT23HR-WM

*see page 10 for mount dimensions

(mount sold separately)

1. Fasten the adapter to

the bracket.

2. Drill the screw holes in the

wall according to the template.

Then insert the plastic plugs

into the holes.

.32”

3.10”

3.94”

Installation Using Semi-Flush Ceiling Mount VT-TPT20HR-FM

*see page 10 for mount dimensions (mount sold separately)

*The following illustrations are for

demonstration purposes only, and depictions

of the PTZ camera used as an example

will dier from the actual camera.

4. Connect cables, then hook the

safety wire to the adapter stem.

5. Securely attach the camera

to the adapter stem with screws.

Adapter tube

2. Mount the adapter tube to the

bracket and secure it with a screw.

3. Secure the pendent mounting

bracket to the ceiling.

6 7

Attach

8.35”

s Thr

8.35

LAN Configuration

The camera can be accessed on the local network either using the

IP-Tool or directly in a web browser.

Accessing the Camera Using the IP-Tool

1. Make sure the camera and PC are connected to the LAN.

2. Locate the IP-Tool installer at www.

vitekcctv.com/Downloads/Soft-

ware/Transcendent-IPTool_v2.0.2.zip

, then install on the PC. Open

the installed application.

3. Modify the IP address. The default IP address is 192.168.226.201.

Click the information of the camera listed in the above table to show

the network information on the right side. Modify the IP address and

gateway of the camera and make sure its network address is in the

same local network segment as the computer’s. Please modify the

IP address of your device according to the practical situation.

For example, the IP address of your computer

is 192.168.13.4. So the IP address of the

camera shall be changed to 192.168.13.X.

After modification, please input the password

of the administrator and click “Modify” button

to modify the setting.

** Default admin password: “123456".

N etwor k C abl e N etwor k C a bl e

Switch

R outer C omputer

P T Z C a mer a

LAN Configuration

The camera can be accessed on the local network either using the

IP-Tool or directly in a web browser.

Accessing the Camera Using the IP-Tool

1. Make sure the camera and PC are connected to the LAN.

2. Locate the IP-Tool installer at www.

vitekcctv.com/Downloads/Soft-

ware/Transcendent-IPTool_v2.0.2.zip

, then install on the PC. Open

the installed application.

3. Modify the IP address. The default IP address is 192.168.226.201.

Click the information of the camera listed in the above table to show

the network information on the right side. Modify the IP address and

gateway of the camera and make sure its network address is in the

same local network segment as the computer’s. Please modify the

IP address of your device according to the practical situation.

For example, the IP address of your computer

is 192.168.13.4. So the IP address of the

camera shall be changed to 192.168.13.X.

After modification, please input the password

of the administrator and click “Modify” button

to modify the setting.

** Default admin password: “123456".

N etwor k C abl e N etwor k C a bl e

Switch

R outer C omputer

P T Z C a mer a

8 9

4. Double-click the IP address and then the system will pop up the

web browser to connect IP-CAM. Edge in IE mode / IE browser

will download the Active X. control. After downloading, a login

window will pop up as shown below:

Input the user name and password to log in.

Default user name: admin / Default password: 123456.

Directly Access Through a Web Browser

The default network settings are as shown below:

IP address: 192.168.226.201 HTTP: 80

Subnet Mask: 255.255.255.0 Data Port: 9008

Gateway: 192.168.226.1

You may use the above default settings when you log in the camera for

the first time.

1. Manually set the IP address of the PC. The network segment should

be the same as the default settings of IP-CAM. Open the network

and share center. Click “Local Area Connection” to pop up the

following window.

Select “Properties” and then select Internet protocol according to the

actual situation (for example: IPV4). Next, click “Properties” button to

set the network of the PC.

2. Open Edge in IE mode / IE browser and input the default address

of IP-CAM and confirm. Edge in IE mode / IE browser will

download Active X control.

3. After downloading Active X control, the login dialog box will pop up.

4. Input the default username and password and then enter to view.

WAN Configuration

Access the camera by the router or virtual server for example.

1. Make sure the camera is connected to the LAN; Then log into the

menu to set up the port number.

the IP address.

4. Open the web browser and input its WAN IP and HTTP port to

access the IP-CAM.

3. Go to the router’s management interface through IE browser to

forward the IP address and port of IP-CAM in the “Virtual Server”.

2. Open Edge in IE mode / IE browser and input the default address

of IP-CAM and confirm. Edge in IE mode / IE browser will

download Active X control.

3. After downloading Active X control, the login dialog box will pop up.

4. Input the default username and password and then enter to view.

WAN Configuration

Access the camera by the router or virtual server for example.

1. Make sure the camera is connected to the LAN; Then log into the

menu to set up the port number.

the IP address.

4. Open the web browser and input its WAN IP and HTTP port to

access the IP-CAM.

3. Go to the router’s management interface through IE browser to

forward the IP address and port of IP-CAM in the “Virtual Server”.

10 11

Installation Mount Dimensions

VT-TPT20HR-FM

VT-TPT20HR-PM

VT-TPT23HR-WM

10.07”

5.32”

3.94”

7.22”

2.48”

3.51”

2.48”

2.54”

9.17”

5.10”

4.27”

Inhaltsverzeichnis

Andere Vitek Sicherheitskamera Handbücher

Vitek

Vitek VTD-TND4RFA4 Bedienungsanleitung

Vitek

Vitek VTC-C2BAZE Bedienungsanleitung

Vitek

Vitek VTC-IR40-N Bedienungsanleitung

Vitek

Vitek VTC-IRLED30HD Bedienungsanleitung

Vitek

Vitek Mighty VTD-MP2810WDR Bedienungsanleitung

Vitek

Vitek VTD-MH2910 Bedienungsanleitung

Vitek

Vitek VTD-TNMD4RFS Bedienungsanleitung

Vitek

Vitek VTC-IRLED30A Bedienungsanleitung

Vitek

Vitek VTC-C770DN/IP2 Bedienungsanleitung

Vitek

Vitek Transcendent VTC-THB5RM Bedienungsanleitung

Vitek

Vitek Transcendent VTD-TND4RFA3/-2 Bedienungsanleitung

Vitek

Vitek VTC-AR2B4FN Bedienungsanleitung

Vitek

Vitek VTC-THB8R2 Bedienungsanleitung

Vitek

Vitek Transcendent VTC-TNT8RMS Bedienungsanleitung

Vitek

Vitek Transcendent VT-TPTZ37HRA-4PNS Bedienungsanleitung

Vitek

Vitek VTC-TNT4RMS Bedienungsanleitung

Vitek

Vitek VT-IR1C/24 Bedienungsanleitung

Vitek

Vitek TRANSCENDENT VTC-TNB8FADW-2 Bedienungsanleitung

Vitek

Vitek VTC-C770/WDR Bedienungsanleitung

Vitek

Vitek Transcendent VT-TPTZ-B10X5N Bedienungsanleitung

Vitek

Vitek VTC-TNT2HR3F2 Bedienungsanleitung

Vitek

Vitek Transcendent VTC-THB2RFS Bedienungsanleitung

Vitek

Vitek VTC-C2B-HS Bedienungsanleitung

Vitek

Vitek VTD-HOCR2812/V Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Lumens

Lumens VC-A50PNW Bedienungsanleitung

Security Cameras Direct

Security Cameras Direct CFC6042IR Bedienungsanleitung