Vivo STAND-SIT1DD Bedienungsanleitung
Sit to Stand Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-sit1dd
SKU: STAND-SIT1DD
2 3
ASSEMBLY STEPS
STEP 1
PACKAGE CONTENTS
TOOLS NEEDED
WARNING!
Phillips
Screwdriver
A (x1)
Base
B(x1)
Adjustable Arm
C(x1)
Smartphone
Tray
O (x1)
6mm Allen
Wrench
P(x1)
Grommet Base
Plate
N(x1)
4mm Allen
Wrench
J (x1)
Clamp
K (x1)
VESA Plate
L (x1)
Cable Clip
M (x1)
3mm Allen
Wrench
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
D(x1)
Keyboard
Tray
E(x1)
Lower Support
Arm
F (x1)
Upper Support
Arm
G(x1)
Rear Cover
H (x1)
Clamp Brace
I (x1)
Clamp Plate
R(x2)
Suppport Plate
Q(x2)
Carriage Bolt
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
M-A (x4)
M4x12
M-C (x4)
D5 Washer
M-B (x4)
M5x12
OPTION A: Clamp Installation
Attach clamp brace (H) to base (A) using M6x12 bolts (V), and tighten with 4mm Allen wrench (N).
Place clamp plate (I) on top of clamp (J). Install clamp (J) to upper holes of clamp brace (H) for a desk
thickness of 3/8” to 1-1/2” (10 - 40mm), or to lower holes for a desk thickness of 1-1/2” to 3-1/4” (40 -
84mm), and tighten with Allen wrench (P). Place assembled base on edge of desk and tighten clamp
bolts evenly with 6mm Allen wrench (O).
T (x2)
M8x25
S(x1)
Wrench
U(x6)
ST4.8x16
W(x2)
M5x10
V(x4)
M6x12
Y (x2)
D8 Washer
X(x2)
M8 Nut
OPTION B: Grommet Installation
Place carriage bolts (Q) into square holes in grommet base plate (P). Attach grommet base plate to
base (A) using M6x12 bolts (V), and tighten with 4mm Allen wrench (N). Place assembled base over
cable grommet hole in desktop, and tighten using support plates (R), lock washers (Y) and M8 nuts
(X), and tighten with crescent wrench (S). If a grommet hole isn’t present, drill a 3/8” (10mm) hole
through the desktop for each bolt.
HV
N
A
J
I
10-40m m
40-84m m
O
Q
P
N
VRYS
X
2.2 - 19.8lbs
(1 -9 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
4 5
STEP 2 STEP 6
Mount upper support arm (F) to lower support arm using M8x25 bolts (T) and tighten with 6mm Allen
wrench (O).
Adjust keyboard tray tilt using the 4mm Allen
wrench (N). Turn the adjustment screw clockwise
to tilt up to position 1a, and counter-clockwise to
tilt down to position 1b. Install the knob (E2) to
lock the position.
STEP 8
STEP 5
Assemble keyboard tray (D) to lower support arm using ST4.8x16 screws (U).
Carefully extend the adjustable arm
(B) to the raised position as shown.
Insert the adjustable arm into the
socket of the base, then secure
using the 3mm Allen wrench (M).
STEP 3
Remove the knob from the lower support arm (E) to separate into lower support arm (E1) and knob
(E2).
STEP 4
Assemble smartphone tray (C) to lower support arm using M5x10 screws (W).
STEP 7
Place the support arm/tray assembly onto the upper
post of the adjustable arm, then secure using the
3mm Allen wrench (M).
B
M
E
E2
E1
C
W
E1
D
U
O
T
F
M
N
E2
2
1a
1a
1b
1b
6 7
STEP 9
STEP 10
Place the monitor with VESA plate into the bracket on the upper support arm, then turn the screw on
the bracket to secure the monitor.
Install the VESA plate (K) to monitor using M4x12 bolts (M-A) or M5x12 bolts (M-B) with washers (M-C),
making sure the rounded edges of the rear bracket are facing up.
STEP 11
Loosen knob in back to adjust monitor height. To adjust gas spring support, turn the hex screw on
top of the rear joint using the 6mm Allen wrench (O). Counter-clockwise will increase support, and
clockwise will decrease support.
TV
TV
TV
M- C
M- A
M- B
K
11
2
O
1
Adjust as Desired
STEP 12
Install rear cover (G) to clamp brace if the
clamp option was used. Install cable clip (L) to
back of upper support arm and remove cable
covers from base and adjustable arm.
STEP 13
Organize cables and reinstall cable covers to base
and adjustable arm.
1
L
2
G
2
O
N
M
1
+10°
-10°
±180°
±180°
±90°
±10°
Last Updated: 11/14/2018
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
Inhaltsverzeichnis
Andere Vivo Rack & Stand Handbücher
Vivo
Vivo MOUNT-V002W Bedienungsanleitung
Vivo
Vivo STAND-RACE1A Bedienungsanleitung
Vivo
Vivo DESK-V000S Bedienungsanleitung
Vivo
Vivo STAND-V200B Bedienungsanleitung
Vivo
Vivo STAND-V011H Bedienungsanleitung
Vivo
Vivo STAND-V002OU Bedienungsanleitung
Vivo
Vivo MOUNT-RAIL02W Bedienungsanleitung
Vivo
Vivo CART-V03E Bedienungsanleitung
Vivo
Vivo MOUNT-UVM01 Bedienungsanleitung
Vivo
Vivo STAND-MIC03L Bedienungsanleitung
Vivo
Vivo STAND-V012F Bedienungsanleitung
Vivo
Vivo STAND-V004TG Bedienungsanleitung
Vivo
Vivo STAND-TS38C-T Bedienungsanleitung
Vivo
Vivo MOUNT-KB5SP Bedienungsanleitung
Vivo
Vivo MOUNT KB04C Bedienungsanleitung
Vivo
Vivo MOUNT-MS01A/W Bedienungsanleitung
Vivo
Vivo MOUNT-POLE01 Bedienungsanleitung
Vivo
Vivo STAND-V004FG Bedienungsanleitung
Vivo
Vivo STAND-LAP2/W Bedienungsanleitung
Vivo
Vivo STAND-V104A Bedienungsanleitung
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
