Vivotek FD8163 Bedienungsanleitung
EN - 1
English
Power off the Network Camera as
soon as smoke or unusual odors are
detected.
Keep the Network Camera away
from water. If the Network Camera
becomes wet, power off immediately.
Do not place the Network Camera
around heat sources, such as a
television or oven.
Refer to your user's manual for the
operating temperature.
Keep the Network Camera away from
direct sunlight.
Do not place the Network Camera in
high humidity environments.
Warning Before Installation
Software CD
FD8163 Alignment Sticker
T10 Torx Screwdriver/ Screws / DC
connector / Plastic Anchors / AV
Cable
5
1
0
0
0
0
2
1
1
G
Package Contents
1
Quick Installation Guide /
Warranty Card
EN - 2
Physical Description
2
1 23 74 5 86
Ethernet
Micro SD Card
Audio InAV Out
Reset
Int. NTSC
PALExt.
Camera Front View
Camera Rear View
Light Sensor
Lens
Built-in
Microphone
PIR Sensor
Black Cover
IR LEDs
(8 units, effective up to 15m)
Auto Focus Button
General IO Terminal
Block
Microphone In (pink)
Audio/Video Out
(green)
Jumpers
Microphone Video Output
internal
external
NTSC
60Hz
PAL
50Hz
1 2
Reset Button
Micro SD/SDHC/
SDXC Card Slot
10/100BaseT
Ethernet
The max. output load from
pins #7 and 8 is 50mA.
NOTE:
1 DC 12V-
2 DC 12V+
3 AC24V_2
4 AC24V_1
5 DI- (GND)
6 DI+
7 DO-
8 DO+ (+12V)
Remove foam pad.
EN - 3
English
Hardware Installation
3
FD8163
50
50
5m
41
41 5m
Before installing your camera,
make sure the built-in PIR (Passive
Infrared Sensor) can be directed
toward the area of interest, where
possible intrusion may occur. (The
sensitivity of PIR sensor depends
on the object size and temperature
differences between the object and
the background environment.)
Dome Cover Bottom of the Camera
Top View Side View
LCD Monitor/
Camera tester AV Out
NOTE:
You may use the included AV cable to connect a camera tester for initial conguration at
the installation site.
Remove the dome cover using the included T10 Torx
screwdriver. You should then jot down the MAC address
at the bottom of the camera.
EN - 4
General Connection (without PoE)
Network Deployment
4
POWER C
OLLIS
ION
LINK
RE
CEIVE
PARTITION
12345
1. If you have external DI devices, make the connection from general I/O terminal block.
2. Ethernet, power, and other cables are user-supplied.
3. Connect the AC cables from the terminal block as an alternate power source. The IO
cables are user-supplied.
1. Attach the alignment sticker to the ceilling/wall.
2. Through the two circles on the sticker, drill two pilot holes into the ceilling/wall.
3. The Network Camera can be mounted with the cable routed through the ceiling/wall or
from the side. If you want to feed the cable through the ceiling/wall, drill a cable hole.
4. Hammer the supplied plastic anchors into the holes.
5. Align the two holes on each side of the camera base with the two plastic anchors on the
ceilling/wall, insert the supplied screws to corresponding holes and secure them with a
screwdriver.
Wall Mount
Ceiling Mount
Ethernet
Switch
Pin3 & 4 AC 24V
Pin #3 & 4 AC 24V as alternate power are for
indoor use only
NOTE:
EN - 5
English
POWER C
OLLIS
ION
LINK
RE
CEIVE
PARTITION
12345
Power over Ethernet (PoE)
POWER C
OLLIS
ION
LINK
RE
CEIVE
PARTITION
12345
When using a non-PoE switch
Use a PoE power injector (optional) to connect between the Network Camera and a
non-PoE switch.
When using a PoE-enabled switch
This Network Camera is PoE-compliant, allowing transmission of power and data via a
single Ethernet cable. Follow the below illustration to connect the Network Camera to a
PoE-enabled switch via Ethernet cable.
Non-PoE Switch
PoE Power Injector
(optional)
PoE Switch
1. This equipment is only to be connected to
PoE networks without routing to outside
plants.
2. For PoE input connections, use only UL
listed I.T.E. with PoE output.
NOTE:
EN - 6
1. Install “Installation Wizard 2” from the Software Utility directory on the software CD.
2. The program will conduct an analysis of your network environment. After your network is
analyzed, please click on the “Next” button to continue the program.
3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network
Cameras on the same LAN.
4. After a brief search, the main installer window will pop up. Double-click on the MAC
address that matches the one printed on the camera label or the S/N number on the
package box label to open a browser management session with the Network Camera.
Assigning an IP Address
5
For further setup, please refer to the user's manual on the software CD.
Ready to Use
6
1. A browser session with the Network Camera should prompt as shown below.
2. You should be able to see live video from your camera. You may also install the 32-
channel recording software from the software CD in a deployment consisting of multiple
cameras. For its installation details, please refer to its related documents.
EN - 7
English
Based on the live image retrieved from the camera, adjust the camera lens to the desired
view angle:
1. Turn the lens module left and right.
2. Loosen the tilt adjustment screws on both sides of the camera and then turn the lens
module up and down. Upon completion, tighten the screws.
3. Turn the lens to adjust the image orientation.
Adjusting the Lens
7
1
23
Pan 350° Rotate 350°
Tilt 65°
The sophisticated 3-axis mechanism design offers very exible, easy hardware installation
for either ceiling or wall mount.
3-axis Mechanism Design
Focus window
To adjust the zoom factor and focus range
1. The camera comes with a motorized vari-focal lens
module. With a web console, you can enter the
Conguration > Media > Image > Focus page to
tune the image zoom and focus.
2. On this page, you can pull the Zoom and Focus
pointers, set up a Focus window, and use the
Perform auto focus button to automatically obtain
an optimal focus result. You may also manually
fine-tune zoom and focus using the various
functional buttons. Please refer to your User
Manual for more information.
EN - 8
When mounting the camera, you can use the key hole slot at the bottom. The key hole
slot helps facilitate installation and a safe mounting.
1. First fasten a pioneer screw to the wall/ceiling. Mount the camera to the screw.
2. Use a pencil to mark the locations of the 3 permanent mounting holes.
3. When cabling and the initial adjustment is done, mount the camera by fastening
screws to the 3 mounting holes.
Mounting Holes
Key Hole Slot
Pioneer Screw
NOTE:
3. You may also push the Auto Focus button on the
camera to obtain the same results especially when
you are using camera tester for onsite adjustment.
EN - 9
English
1. If you choose to feed the cable through the ceiling/wall, arrange the cables neatly
through the cable hole A (not shown in the drawing). If you choose to feed the cable
from the side, remove plate B.
2. Attach the dome cover to the camera as the direction shown below. Tighten two screws
from the sides of the dome cover.
3. Finally, make sure all parts of the camera are securely installed.
Completion
8
1
B
3
2
A
Be aware of the
cable route!
Dome Cover
Andere Handbücher für FD8163
6
Inhaltsverzeichnis
Andere Vivotek Sicherheitskamera Handbücher
Vivotek
Vivotek SD8333-E Bedienungsanleitung
Vivotek
Vivotek PZ8111 Bedienungsanleitung
Vivotek
Vivotek SF8174 Bedienungsanleitung
Vivotek
Vivotek FD9189-H-v2 Bedienungsanleitung
Vivotek
Vivotek FD9381-HTV Bedienungsanleitung
Vivotek
Vivotek FD8136 Original Betriebsanleitung
Vivotek
Vivotek IP7161 Bedienungsanleitung
Vivotek
Vivotek IB836BA-HT Bedienungsanleitung
Vivotek
Vivotek FD816BA-HF2 Bedienungsanleitung
Vivotek
Vivotek IP6117 Bedienungsanleitung
Vivotek
Vivotek FE8174V Bedienungsanleitung
Vivotek
Vivotek TB9331-E Bedienungsanleitung
Vivotek
Vivotek FD9369 Bedienungsanleitung
Vivotek
Vivotek IP7133 Bedienungsanleitung
Vivotek
Vivotek FD8166 Bedienungsanleitung
Vivotek
Vivotek FD9391-EHTV Bedienungsanleitung
Vivotek
Vivotek FD8166 Bedienungsanleitung
Vivotek
Vivotek FD9181-HT Bedienungsanleitung
Vivotek
Vivotek Supreme MD8563-DEH Bedienungsanleitung
Vivotek
Vivotek IP8161-SS Bedienungsanleitung
