Vivotek IP8332-C Bedienungsanleitung
Quick Installation Guide
VIVOTEK INC.
6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C.
|T:+886-2-82455282|F:+886-2-82455532|E:[email protected]
VIVOTEK USA, INC.
2050 Ringwood Avenue, San Jose, CA 95131
|T: 408-773-8686|F: 408-773-8298|E: [email protected]
Outdoor • Day & Night • Weather-proof • Cable Management
All specications are subject to change without notice.
Copyright 2012 VIVOTEK INC. All rights reserved.
c
P/N:625018500G Rev. 1.0
IP8332-C Bullet
Network Camera
English 繁中 日本語 Español Português
簡中 Français Deutsch Italiano Türkçe Polski Русский Česky Svenska
EN-1
English
Warning Before Installation
Refer to your user’s manual for the
operating temperature.
Power off the Network Camera as
soon as smoke or unusual odors are
detected.
Do not touch the Network Camera
during a lightning storm.
Do not place the Network Camera on
unsteady surfaces.
Do not drop the Network Camera.
Do not insert sharp or tiny objects
into the Network Camera.
Replacing or failing to properly
install the waterproof components,
e.g., cables or cable glands, will void
our IP65/66/67 warranty.
Package Contents
1
5
1
0
0
0
0
2
2
1
G
Software CD
IP8332-C
L-type Hex Key Wrench / Dessicant
Bag / Screws / RJ45 Female-Famale
Coupler / Waterproof Connector
Quick Installation Guide / Warranty
Card / Alignment Sticker
Ball Swivel
Mount Bracket
EN-2
Physical Description
2
Connectors
Ethernet 10/100 RJ45 Plug
Power Cord Socket (Black)
General I/O Terminal Block
Front Panel
IR LEDs
Lens
Reset Button
MicroSD/SDHC
Card Slot
Light Sensor
Rear Panel
EN-3
English
Hardware Installation
3
IMPORTANT:
Although the camera and the cable gland on the camera's end are waterproof, the cable
molding at the other end is not waterproof.
Measures should be taken to prevent water from leaking in through the cable-end
molding, such as the use of expanding foam sealant, putties, and so on. Note that the
cable gland on the camera should also be securely fastened to attain its waterproof
functionality.
Cable Gland
Waterproof Not Waterproof
Cable Molding
3
Silica gel
1
2
4
Micro
SD
If you prefer installing a MicroSD card as onboard storage:
1. Loosen the waterproof connector, and then remove the rubber seal, and the
waterproof connector.
2. Loosen and open the rear cover.
3. Install a MicroSD/SDHC card.
4. Tear down the aluminum foil vacuum bag and take out the dessicant bag. Attach the
supplied dessicant bag to the inner side of the Network Camera. (Please replace the
dessicant bag with a new one every time you open the rear cover.)
5. Make sure all cable lines are securely connected.
EN-4
5. Tighten the rear cover, rubber seal and waterproof connector.
7
6
5
6. Pass the cables through the center of the ball swivel mount bracket, one at a time.
7. Fasten the bracket to the camera using 3 hex socket screws.
8. Loosen the fastening ring on the mount bracket, and aim the camera at the area of
your interest. When done, tighten the fastening ring.
Fastening ring
75º Tilt
360º Pan
NOTE:
The camera weighs up to 1.28 kgs.
Make sure the mounting surface can
support this camera.
EN-5
English
Network Deployment
4
POWER C
OLLIS
ION
LINK
RE
CEIVE
PARTITION
12345
1. If you have external devices such as
sensors and alarms, make connections
from general I/O terminal block.
2. Use the supplied RJ45 female/female
coupler to connect the Network Camera
to a switch.
3. Connect the power cable from the
Network Camera to a power outlet.
GND : Ground
DI : Digital Input
AC24V : 24V-
AC24V : 24V+
GND
DI
AC24V
AC24V
General Connection (without PoE)
9
Ceiling Mount
Wall Mount
9. Secure the Network Camera to a wall or ceiling.
EN-6
Power over Ethernet (PoE)
When using a non-PoE switch
Use a PoE power injector (optional) to connect between the Network Camera and
a non-PoE switch.
When using a PoE-enabled switch
The Network Camera is PoE-compliant, allowing transmission of power and data
via single Ethernet cable. Follow the below illustration to connect the Network
Camera to a PoE-enabled switch via Ethernet cable.
POWER C
OLLIS
ION
LINK
RE
CEIVE
PARTITION
12345
Non-PoE Switch
PoE Power Injector
(optional)
POWER C
OLLIS
ION
LINK
RE
CEIVE
PARTITION
12345
PoE Switch
EN-7
English
1. Install the "Installation Wizard 2" from the Software Utility directory on the software
CD.
2. The program will conduct an analysis of your network environment. After your network
is analyzed, please click on the "Next" button to continue the program.
3. The program will search for VIVOTEK Video Receivers, Video Servers or Network
Cameras on the same LAN.
4. After a brief search, the main installer window will pop up. Double-click on the MAC
address that matches the one printed on the camera label or the S/N number on the
package box label to open a browser management session with the Network Camera.
Assigning an IP Address
5
For further setup, please refer to user’s manual on the software CD.
Ready to Use
6
1. A browser session with the Network Camera should prompt as shown below.
2. You should be able to see live video from your camera. You may also install the
32-channel recording software from the software CD in a deployment consisting of
multiple cameras. For its installation details, please refer to its related documents.
EN-8
Secure the Shooting Angle
6
When you are done with tuning the eld of view and obtain a satisfactory image, tighten
the fastening ring and the 3 small hex screws on the ball-swivel bracket.
Orient the camera so that the protruding edge of its sunshield is positioned against the
direction of direct sunlight.
NOTE:
Protruding edge
Quick Installation Guide
VIVOTEK INC.
6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C.
|T:+886-2-82455282|F:+886-2-82455532|E:[email protected]
VIVOTEK USA, INC.
2050 Ringwood Avenue, San Jose, CA 95131
|T: 408-773-8686|F: 408-773-8298|E: [email protected]
Outdoor • Day & Night • Weather-proof • Cable Management
All specications are subject to change without notice.
Copyright 2012 VIVOTEK INC. All rights reserved.
c
P/N:625018500G Rev. 1.0
IP8332-C Bullet
Network Camera
English 繁中 日本語 Español Português
簡中 Français Deutsch Italiano Türkçe Polski Русский Česky Svenska
Andere Handbücher für IP8332-C
1
Inhaltsverzeichnis
Andere Vivotek Sicherheitskamera Handbücher
Vivotek
Vivotek IP71353 Bedienungsanleitung
Vivotek
Vivotek AE2101 Bedienungsanleitung
Vivotek
Vivotek FD8133V Bedienungsanleitung
Vivotek
Vivotek FD8169A Bedienungsanleitung
Vivotek
Vivotek fd8371v Bedienungsanleitung
Vivotek
Vivotek IP2112 Bedienungsanleitung
Vivotek
Vivotek SUPREME IP9165-HT Bedienungsanleitung
Vivotek
Vivotek FD8166A-N Bedienungsanleitung
Vivotek
Vivotek FD8166A-N Bedienungsanleitung
Vivotek
Vivotek SD8161 Bedienungsanleitung
Vivotek
Vivotek FD9369 Bedienungsanleitung
Vivotek
Vivotek IP8330 Bedienungsanleitung
Vivotek
Vivotek ip8364-c Bedienungsanleitung
Vivotek
Vivotek MD8563-EHF4 Bedienungsanleitung
Vivotek
Vivotek IT9380-H Bedienungsanleitung
Vivotek
Vivotek IP8371E Bedienungsanleitung
Vivotek
Vivotek IZ9361-EH Bedienungsanleitung
Vivotek
Vivotek MD8562 Bedienungsanleitung
Vivotek
Vivotek TD5196A Bedienungsanleitung
Vivotek
Vivotek IP816A-LPC Bedienungsanleitung
