VOLTA Vortex U4015 Bedienungsanleitung

Vortex U4015

Instruction Manual

35125 VORTEX U4015 IFU V3.indd 2 2/10/08 1:37:23 PM

Thank you for choosing a Volta Vortex vacuum cleaner. These operating

instructions cover all Vortex models; this means that with your specic model,

some accessories may or may not be included.

Table of contents

Accessories and important safety instructions 3

Service and warning on materials collected 3-4

Before starting and getting the best results 5

Removing the contents of the dust container 6

Replacing the lters 7

Cleaning the motor lter 7

Replacing the exhaust lter 7

Replacing and cleaning the cartridge lter 8

Cleaning the hose and nozzle 9

Trouble shooting and customer information 10

Warranty 11

Customer record 12

35125 VORTEX U4015 IFU V3.indd 3 2/10/08 1:37:23 PM

ACCESSORIES AND PRECAUTIONS

ACCESSORIES

1. HEPA lter

2. Telescopic tube

3. Hose

4. Hose handle with suction control

5. Dual purpose oor nozzle

6. Upholstery nozzle with plush plate

7. Crevice nozzle

8. Turbo nozzle

9. Accessory holder

10. Hard oor tool

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE)

When using an electrical appliance basic precautions should always be followed,

including the following.

Before connecting the cleaner to an electrical supply outlet ensure that the voltage marked on

the rating plate (on the underside of the cleaner) is correct for your electrical supply.

If it does not comply do not use the cleaner prior to contacting the manufacturer.

WARNING – To reduce the risk of re, electric shock or injury:

1. Do not leave the vacuum cleaner when plugged in. Remove the plug from the outlet when

not in use and before servicing.

2. To reduce the risk of electric shock, do not use outdoors or on wet surfaces.

3. This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the appliance by a person responsible for

their safety.

Children should be supervised to ensure that they do not play with the appliance.

4. The appliance is not intended for use by young children or inrmed persons

without supervision.

5. Use only as described in this manual. Use only the manufacturers

recommended attachments.

6. Do not use with a damaged cord or plug. If the vacuum cleaner is not working as it should,

has been dropped, damaged, left outdoors or dropped in water, arrange for it to be taken to

a service centre before using.

7. Do not pull or carry on the cord, or use as a handle. Do not close doors on the cord or pull

around sharp edges or corners. Do not run the vacuum cleaner over the cord. Keep the cord

away from heated surfaces.

8. Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.

9. Do not handle the plug or vacuum cleaner with wet hands.

10. Do not put any objects into openings. Do not use with openings blocked. Keep free of dust,

lint, hair and anything that may reduce airow.

11. Keep hair, loose clothing, ngers and all parts of the body away from the openings and

moving parts.

12. Turn all controls o before unplugging the appliance.

Additional Warnings page 4

9. 10.

35125 VORTEX U4015 IFU V3.indd 4 2/10/08 1:37:25 PM

Warnings Continued

13. Use extra care when cleaning on stairs.

14. Do not use to collect ammable or combustible liquids such as gasoline or use in areas

where they may be present.

15. Unplug the appliance prior to connecting the hose.

16. Do not collect anything that is burning or smoking such as cigarettes, matches or hot

ashes.

17. Do not use without lters in place.

18. Do not use extension cords or outlets with inadequate current carrying capacity.

19. Do not use your vacuum cleaner on carpet cleaning foams, sharp or heavy building

materials or plaster dust or other ne powders. They could damage or clog the cartridge

lter and cause failure to other key parts in your vacuum cleaner and render your

warranty invalid.

20. Store your vacuum cleaner indoors in a cool dry area.

21. Keep your work area well lighted.

22. Unplug electrical appliances prior to vacuuming them.

SERVICE & REPAIR

It is dangerous to alter the specications or modify the product in any way. Under no

circumstances should you attempt to repair the cleaner yourself.

Repairs undertaken by unauthorised or inexperienced persons may cause injury and / or

serious malfunction of the cleaner and may void the warranty conditions on page 10 of this

instruction booklet.

NB! To avoid injury and prevent damage to the vacuum cleaner a defective cord must only

be replaced by an authorised service provider approved by the manufacturer to avoid a

hazard. The vacuum cleaner should be serviced by an authorised service provider and only

genuine Volta parts should be used.

DOUBLE INSULATION

Your vacuum cleaner is double insulated. This means that all external parts are electrically

insulated from the mains. This is done by placing insulation barriers between the electrical

and mechanical components, making it necessary for the cleaner not to be earthed.

WARNING: On collection of proprietary carpet conditioning powder, plaster / concrete dust

and talcum powder, it is recommended that the dust container is emptied and the cartridge

lter is cleaned after each use. Some of thee preparations contain substances which while

left in the vacuum cleaner for extended periods could cause damage. Many air fresheners,

household deodorants, sprays and polishes contain highly inammable gas propellants,

because of this it is particularly important that these products are used strictly in accordance

with the relevant manufacturers instructions. It is essential that none of the above products

are sprayed directly into the vacuum cleaner or any of the lters, hose assembly or dust

chamber.

35125 VORTEX U4015 IFU V3.indd 5 2/10/08 1:37:25 PM

BEFORE STARTING

1. Always operate the cleaner with the dust container installed.

2. Fitting and Removal of the Hose Assembly: - To connect the hose to the suction inlet,

insert the hose until it clicks into position. Remove the hose from the suction inlet by

pushing the button on the coupling to disengage the securing lock and withdraw the

hose from the inlet.

3. Attach the telescopic tube to the hose bent end handle and to the oor nozzle.

4. Extend the power cord by holding the plug and insert the plug into the power outlet.

5. Press the foot pedal to rewind the power cord; with your hand guide the cord to prevent

it from striking you or any other objects.

6. Press the On/O pedal to start and stop the vacuum cleaner.

7. Adjust the suction power by sliding the variable speed controller positioned on the top

of the vacuum cleaner or by adjusting the suction control slide on the hose bent handle.

GETTING THE BEST RESULTS

Hard oors: Use the dual-purpose oor nozzle with the left pedal in position

(8). Use the Hard Floor Tool (10) on slate, tiled and highly polished timber oors.

Carpets: Use the dual-purpose oor nozzle with the left pedal in position

(9). Use the Turbo Nozzle (11) to lift short carpet pile and for vacuuming stubborn

u and the picking up of pet hair.

Reduce the suction power for rugs and fabrics.

Upholstered furniture: Use the upholstery nozzle.

Skirting boards, crevices, corners etc.: Use the crevice nozzle.

11.10.

35125 VORTEX U4015 IFU V3.indd 6 2/10/08 1:37:27 PM

REMOVING THE CONTENTS OF THE DUST CONTAINER

Always operate the cleaner with the dust container installed.

1. Remove the dust container by pushing the Open Button on the handle.

2. Remove the contents of the dust container by pushing the orange-coloured

opening button.

3. Close the dust container lid until it clicks.

1. Put the dust container back into the cleaner.

REMOVAL, CLEANING AND FITTING THE PLASTIC CONE ASSEMBLY (Fig. 4)

To ensure there is no restriction of airow resulting in loss of suction after emptying of

the dust container, it is essential that the plastic cone is checked for blockages.

REMOVAL OF THE PLASTIC CONE SECTION

1. Place the dust container upside down with the HEPA lter facing away from you.

2. Open the dust compartment cover ap by pressing the ap release button.

3. The plastic cone assembly is located on the left hand side. Place your thumb and

forenger in the open cavities of the cone assembly, turn clockwise and lift out the

cone assembly.

4. Check for residue build up. If present, wipe clean and replace the cone assembly in the

locking position in the dust container. Turn anti-clockwise to lock it in position. (Please

note that the cone assembly can only be tted one way.)

5. Close the ap and install the dust container in the vacuum cleaner body, ensuring it is

locked into position.

Please note: it is normal for the red light of the indicator to icker ON and OFF

during use. If the dust container is emptied and the indicator is still ickering,

this indicates the HEPA lter and frame is clogged. In this case follow instructions

replacing or cleaning the HEPA lter and frame – page 8 of this booklet.

35125 VORTEX U4015 IFU V3.indd 7 2/10/08 1:37:28 PM

REPLACING THE FILTERS

• Theltersshouldbereplacedtwiceayearormoreoftendependingontheuseofthe

vacuum cleaner and the dust penetration, which is visible by the discolouring of the lter.

• Disconnecttheelectricalpowercordfromthepoweroutletpriortocleaningthelters.

• Alwaysoperatethevacuumcleanerwiththeltersinstalledtoavoidreductionofsuction

and penetration of dust to the motor.

CLEANING THE MOTOR FILTER

If necessary, the motor lter can be washed or replaced at least twice a year or if clogged,

depending on use.

1. Remove the dust container by using the open button on the handle.

2. Remove the lter from its place.

3. Rinse the lter under tap water and leave it to dry completely (over a

period of 24 hours).

2. Put the lter back into its place.

1. Insert the dust container back into the cleaner by pressing it down until it clicks.

For enquiries on spare parts or for your closest service centre to obtain spare parts, please

contact our customer service help line on 1300 365 305(AUS), 0508 730 730(NZ)

REPLACING THE EXHAUST MICROFILTER

The exhaust microlter should be replaced at least twice a year or if clogged.

4. Open the lter front.

5. Remove the exhaust lter with grill.

6. Take the lter out of the lter grill and insert a new exhaust lter.

5. Put the lter with the grill back into the cleaner.

4. Close the lter grill.

35125 VORTEX U4015 IFU V3.indd 8 2/10/08 1:37:30 PM

REPLACING OR CLEANING THE HEPA FILTER AND FRAME

1. Remove the dust container by using the open button on the handle.

2. a) Remove the HEPA lter complete with frame from the dust container after releasing

the locking clips on the side of the lter frame.

b) Tap the HEPA lter face down on a at surface covered with a sheet of paper; this

will dislodge excess residue from the HEPA lter. Dispose of the cover sheet with the

dust residue.

3. If necessary, the HEPA lter and frame can be washed with cold water under a tap

(wash from the underside not the topside).

4. Air dry the HEPA lter for approximately 24 hours to ensure it is completely dry before

re-using. Avoid direct sunlight and extreme drying circumstances. If you wish to use

your appliance while the HEPA lter is drying, you can use the spare HEPA lter enclosed

in the packaging carton.

5. a) Ret the HEPA lter and frame by rstly pressing the button on the left hand side of

the dust container.

b) Position the HEPA lter and frame with tab aligning with the button on the side of

the dust container.

c) Insert the HEPA lter and frame, ensuring the locking clips positioned on both sides

of the frame are secured.

1. Insert the dust container back into the cleaner by pressing it down until it clicks.

NOTE: Do not use cleaning agents and avoid touching the delicate lter surface.

35125 VORTEX U4015 IFU V3.indd 9 2/10/08 1:37:31 PM

CLEANING THE HOSE AND NOZZLE

The vacuum cleaner stops automatically if the nozzle, tube or hose becomes blocked or if

the lters are blocked. This is due to a safety precaution which prevents the motor

overheating. Switch o the cleaner at the mains power outlet and remove the plug from

the power outlet, grasping the plug not the cord for removal. Allow the cleaner to cool

down for approximately 30 minutes.

TUBES AND HOSE

1. Use a exible hose or similar item to clear the tube and hose.

2. Use a exible hose or similar item to clear the hose by“massaging” it. However, be careful

in case the obstruction has been caused by glass or needles caught inside the hose.

NOTE: The warranty does not cover any damage to hoses caused by cleaning them.

CLEANING THE FLOOR NOZZLE

3. To avoid reduction in suction power, frequently clean the dual-purpose oor nozzle. The

easiest way to clean it is by connecting the hose to the vacuum cleaner and using the

hose bent end handle.

35125 VORTEX U4015 IFU V3.indd 10 2/10/08 1:37:32 PM

TROUBLE SHOOTING AND CUSTOMER INFORMATION

TROUBLESHOOTING

THE VACUUM CLEANER DOES NOT START.

1. Check that the power cord is connected to the mains.

2. Check that the plug and power cord are not damaged.

3. Check for a faulty / blown fuse.

THE VACUUM CLEANER STOPS

1. Check whether the dust container is full. If so, empty it.

2. Is the nozzle, tube or hose blocked?

3. Are the lters blocked?

Water has entered the vacuum cleaner

It will be necessary for the Fan Unit / Motor to be replaced by an Authorised Electrolux

Service Agent. Damage to the Fan Unit / Motor caused by the penetration of water is NOT

covered by warranty.

CUSTOMER INFORMATION

Electrolux Pty Ltd decline all responsibility for all damages arising from improper use of

the appliance, or in cases where there has been tampering with the appliance other than

by an Authorised Electrolux Service Agent. This appliance has been designed with the

environment in mind and all plastic parts are marked accordingly for recycling purposes.

For your closest service agent for servicing or to obtain accessories for your vacuum cleaner,

please contact our customer service help line on 1300 365 305(Aus), 0508 730 730(NZ)

If you require further details please consult our website: www.volta.com.au

The symbol on the product or on its packaging indicates that this product may not be

treated as household waste. Instead it shall be handed over to the applicable collection point

for the recycling of electrical and electronic equipment. By ensuring this product is disposed

of correctly, you will help prevent potential negative consequences for the environment and

human health, which could otherwise be caused by inappropriate waste handling of this

product. For more detailed information about recycling of this product please contact your

local city oce, your household waste disposal service or the shop where you purchased

the product.

35125 VORTEX U4015 IFU V3.indd 11 2/10/08 1:37:32 PM

Inhaltsverzeichnis

Andere VOLTA Staubsauger Handbücher

VOLTA

VOLTA VORTEX U4015F Bedienungsanleitung

VOLTA

VOLTA U144 Bedienungsanleitung

VOLTA

VOLTA U4401 Bedienungsanleitung

VOLTA

VOLTA U3410 Handbuch

VOLTA

VOLTA LITE II Bedienungsanleitung

VOLTA

VOLTA U3302 Bedienungsanleitung

VOLTA

VOLTA U1110P Bedienungsanleitung

VOLTA

VOLTA 4510 PRIMEROSE YELLO Bedienungsanleitung

VOLTA

VOLTA Ultima Pet Plus U6011 Bedienungsanleitung

VOLTA

VOLTA Mega Gen 3 U5010 Bedienungsanleitung

VOLTA

VOLTA Elyps 1110 Bedienungsanleitung

VOLTA

VOLTA U1110S Bedienungsanleitung

VOLTA

VOLTA 2825 Bedienungsanleitung

VOLTA

VOLTA U2950 Series Bedienungsanleitung

VOLTA

VOLTA MobiMaxx U3510 Bedienungsanleitung

VOLTA

VOLTA MobiONE UMO1540 Bedienungsanleitung

VOLTA

VOLTA Lilly UB1411 Bedienungsanleitung

VOLTA

VOLTA U4405 Handbuch

VOLTA

VOLTA U4220 Bedienungsanleitung

VOLTA

VOLTA U1112 Bedienungsanleitung

VOLTA

VOLTA U4111 Bedienungsanleitung

VOLTA

VOLTA U3420 Handbuch

VOLTA

VOLTA Dolphin U5001 Bedienungsanleitung

VOLTA

VOLTA U3201 Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung