Voscom VOS-4800FFT Series Bedienungsanleitung

VOS-4800FFT/R series

4-Channel Video + 8 Simplex Audio

Installation Manual

Fiber Optic Transmission Systems

VOSCOM TECHNOLOGIES CO.,LIMITED

WWW.VOSCOM.COM

Important Safety Instructions EN_1

1. Readthese instructions. Keep these instructions. Heed allwarnings. Follow all instructions.

5. Donot use this apparatus near water. Cleanonly with dry cloth.

7. Donot block any ventilation openings. Install in accordance with the manufacturers

instructions.

8. Donot install near any heat sources such as radiators, heatregisters, stoves,or other

apparatus (includingamplifiers) that produce heat.

9. Donot defeat the safety purpose of the polarized or grounding-type plug. A polarized plug

has twoblades withone wider than the other. Agrounding type plug has two blades and a third

grounding prong. The wideblade or the third prong are provided for your safety. Ifthe provided

plug doesnot fitinto your outlet consult an electrician for replacement of the obsolete outlet.

10. Protectthe power cord from being walked on or pinched particularly at plugs,convenience

receptacles, andthe points where they exit from the apparatus.

13. Referall servicingto qualifiedservice personnel. Servicing is required when the apparatus

has beendamaged in any way, suchas power-supply cord or plug is damaged, liquid has been

spilled or objects havefallen into the apparatus,the apparatushas been exposed to rain or

moisture, doesnot operatenormally,or has been dropped.

14. Apparatusshall not be exposed to dripping or splashing and that no objects filled with liquids,

such asvases shall be placed on the apparatus.

15. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatusto rain or

moisture.

16. Installation should be done only by qualified personnel and conform to all local codes.

20. CAUTION: These servicing instructions arefor useby qualified service personnel only.To

reduce therisk of electric shock do not perform any servicing other than that contained in the

operating instructionsunless youare qualifiedto do so.

Website:www.voscom.com

Product Overview En_2

Video

The VOS-4800FFT/R can transmission4-Channel

video and 8 simplex analog auido over singlemode

or multimode optical cable.

Stand-alone orrack-mount. The cards can be inserted

into our 14 slots,19inch 4U or 6U rack-mountable

card cage (VOS-CH04 or VOS-CH06). The card of this model require two slots widths.

System Diagram:

Model Number

Transmitter Receiver Fiber Mode Wavelengths Optical

Power

Budget

Maximum

Transmission

Distance

Multi-Mode 1310nmVOS-4800FFMRVOS-4800FFMT

•The OpticalPower Budgetdata fitMulit-mode(62.5/125 m),Single-Mode(9/125 m).

•When using50/125 m multimode fiber, subtract3 dBfrom the optical power budget.

•Optical transmissiondistance is limited to optical loss of thefiber and any additional loss introduced by connectors,

splices andpatch panels.

•Maximum transmissiondistance is also limited by fiber bandwidth.

•Power adapteris manufactured by thirdparty and is supplied with fitted screw-terminal outputcables.Power

adapter included(for standalone) US, European, UK or Australian powerplug.

•Please feelfree to consult factory for anyspecial requirement and customization

Note:

12dB 1.5km

Single-Mode

VOS-4800FFSRVOS-4800FFST 12dB 20km

VOS-4800FFST-4

VOS-4800FFST-6

VOS-4800FFSR-4

VOS-4800FFSR-6

Single-Mode

18dB

25dB

40km

60km

Models and Optical Power Budget:

•Uncompressed Digital Composite Video over onefiber

•Compatible with all PAL,NTSC,SECAM Video Systems

•Multi-mode Fiber Support for Distances up to 1.5 km

•Single-Mode Fiber Support for Distances up to 100 km

•No EMI or RFI and noground loops

•Stand alone or rack-mount

Features:

Audio

1310nm

1550nm

1 Fiber opticCable

Monitor

VOS-4800FFT

Transmitter VOS-4800FFR

Receiver

4 x Video

8 xAudio 8 xAudio

8 x Microphone 8 xSpeaker

Fiber OpticConnector, FC/PC or ST/PC

V1~V4 BNCConnector, 75-ohmanalog video input (Transmitter)/output (Receiver)

Stand-alone Power supply Connector, DC5V3A Input.

Panel & Cable Connection En_3

NOTE1: Digital video optic transmitterand receivershould be used in pairs, one is Transmitter

(LED is red), theother is Receiver (LED is green).

NOTE2: Avoid simultaneously connecting video signals to both the front BNC andrear BNC of the

same channel.Also, since each video channel is factory terminated to 75 ohm, unused BNCs

should notbe used for loop-through video connections.

4Audio Connector, Terminal Block,analog audio input (Transmitter)/output (Receiver)

FRONT PANEL

FTX

REAR PANEL

DC5V

V1 V2 V3 V4

1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8

EXT1 EXT2 EXT3 IP/EXT

None

Panel & Cable Connection En_4

Transmitter (Audio): 8-Channel Simplex Audio Connection (Input)

NOTE: AUDIO SIGNAL AND IMPEDANCE MODE

1) Audio Signal: The audio is Mono Audio in default, can support Stereo audio, but you

should consultfor us before the order.

2) Impedance Mode: The audiois unbalanced mode in default, can support 600 ohm

balanced audio, but you should consult for us before the order

Connect Audio1

Connect GND1

Input

8 Pin Terminal Block

Connect GND2

Connect Audio2

Connect Audio4

Connect GND4

Connect Audio3

Connect GND3

Input

1 2 3 4 5 6 7 8

EXT1

Input

Connect Audio5

Connect GND5

Input

8 Pin Terminal Block

Connect GND6

Connect Audio6

Connect Audio8

Connect GND8

Connect Audio7

Connect GND7

Input

1 2 3 4 5 6 7 8

EXT2

Input

Transmitter EXT1 Terminal Block: 1ch~4ch audio input

Transmitter EXT2 Terminal Block: 5ch~8ch audio input

Website:www.voscom.com

Panel & Cable Connection En_5

Receiver (Audio): 8-Channel Simplex Audio Connection (Output)

NOTE: AUDIO SIGNAL AND IMPEDANCE MODE

1) Audio Signal: The audio is Mono Audio in default, can support Stereo audio, but you

should consultfor us before the order.

2) Impedance Mode: The audiois unbalanced mode in default, can support 600 ohm

balanced audio, but you should consult for us before the order

Connect Audio1

Connect GND1

Output

8 Pin Terminal Block

Connect GND2

Connect Audio2

Connect Audio4

Connect GND4

Connect Audio3

Connect GND3

Output

1 2 3 4 5 6 7 8

EXT1

Output

Connect Audio5

Connect GND5

Output

8 Pin Terminal Block

Connect GND6

Connect Audio6

Connect Audio8

Connect GND8

Connect Audio7

Connect GND7

Output

1 2 3 4 5 6 7 8

EXT2

Output

Receiver EXT1 Terminal Block: 1ch~4ch audio output

Receiver EXT2 Terminal Block: 5ch~8ch audio output

Website:www.voscom.com

Stand-alone Installation En_6

The VOS-4800FFT transmitter/VOS-4800FFR receivercan be mounted into a rack or canbe usedas

a stand-alonemodule. As a stand-alone module, the unit can be placed on a desktop or can be

mounted to a wall.

NOTE: Before mounting the VOS-4800FFT transmitter/VOS-4800FFR receiver, please ensure that

there is adequate space at both ends forviewing the front-panel LEDsand for making the various

rear-panel cableconnections.

Stand-alone Mounting Size: 176.5mm x 158mm x 59mm

Website:www.voscom.com

Rack-mount Installation En_7

Installation Instructions

Typical Configurations:

1:Install the video card into a standard 19inch rack, usinguser-supplied rack-mounting

hardware. Becareful to not damage exposed objects on the back of the card cage unit.

2:If asecondary earth ground connectionis needed, a grounded wire with a ground lug can be

attached to the rackusing the protruding screw provided on the right side of the chassis.

3:If desired, blank panels may beinstalled to cover unused slots. A single blank panel coversa

single slot opening.

4:Each fiber optic plug-in module is equipped with a POWER LED indicator that illuminates

when power is applied to the rack unit.

5:Fiber optic plug-in modules(video cards) can be installed into anyof theavailable 14slots

of thecard cage. Most modules require onlya single slot width, but others, such as the 8-Ch

video Series, require two slot widths.

VOS-CH04:

19 inch4U,14 video card slots, suit for 1-ch,2-ch,4-ch,8-ch(two slots)video cards.

Support oneslide-in power supply AC100V~AC240V

VOS-CH06:

19 inch6U,16 video card slots, suit for 1-ch,2-ch,4-ch,8-ch(two slots)video cards.

Support two slide-in power supply AC100V~AC240V, one for redundancy.

Website:www.voscom.com

The VOS-4800FFT transmitter/VOS-4800FFR receivercan be installed into our rackmount chassis,

VOS-CH04 orVOS-CH06, which can be mounted into an industry-standard 19-inch equipmentrack.

Troubleshooting En_8

Indicator Status Meaning Possible Cause Corrective Action

Power LED

Light Power isbeing applied

to the module. --- No actionrequired.

Not Light Power isnot being

applied to the module.

Check powerconnection.

If moduleis rackmounted,

reseat moduleor power

supply asnecessary.

Power connectionis

faulty.

Power supplyhas failed. Replace powersupply.

Loss ofpower occurs due

to trippedcircuit

breaker(s), blownfuse(s),

or faultyelectrical

service.

Check circuit breaker(s),

fuse(s), orelectrical

service asnecessary.

LED indicators on thefront-panel of the transmitter/receiverallow youto monitor signal status,

laser status,data activity, contact closure activation, and operatingpower. Table A~D provide

information aboutthe front-panelindicators and associated troubleshooting guidelines.

Table A: Power Links

Indicator Status Meaning Possible Cause Corrective Action

Video LED(VIDEO 1,VIDEO 2....)

Light Incoming video signal

is present on thechannel. --- No actionrequired.

Not Light

on Transmitter Incoming video signal

is not present on the

channel.

Check power connection

to the video source.

Video source is not

powered on.

Video source is not

connected to the

transmitter.

Check BNC connections.

Coaxial cable is

defective. Replace cable.

Table B: Video Links

Not Light

on Receiver Incoming video signal

is not present on the

channel.

Optical signal is not

being receivedfrom the

transmitter. Optic Fault

LED is also not light.

Refer tothe Optic Fault

LED section in this table.

Video source is not

powered on. Check power connection

to the video source.

Video source is not

connected to the

transmitter.

Check BNC connections.

Coaxial cable connected

to the transmitter is

defective.

Replace cable.

Website:www.voscom.com

Troubleshooting En_9

Indicator Status Meaning Possible Cause Corrective Action

Data(RS485/RS232/RS422) LED

Flashing

Data is being transmitted

onto the fiber by the data

port or is being received

from thefiber by the

data port.

--- No actionrequired.

Table C: Data Links

Indicator Status Meaning Possible Cause Corrective Action

Optic LED

Light The optical signal is being

received andlaser is

operatingproperly.

--- No actionrequired.

Not Light

Table B: Optic Links

Not Light

Data isnot being

transmitted ontothe

fiber bythe data port or

is notbeing received

from thefiber by the

data port.

Data isnot present on

the channel. No actionrequired.

Data connectionis faulty. Check dataconnections.

Data communication

cable isdefective. Replace cable.

The optical signal is

not beingreceived.

Remote fibermodule is

not poweredon. Check power connections.

Replace powersupply if

necessary.

Fiber optic cable is not

connected. Check fiberoptic

connections.

Fiber optic cable

connectors aredirty or

are damaged.

Clean, polish, or replace

fiber opticcable

connectors asnecessary.

Fiber optic cable is

defective. Replace cable.

A problemexists with

the optical power

budget.

Verify thatlosses in fiber

optic cable do not exceed

the optical power budget

specification of the fiber

optic link. If the losses do

exceed theoptical power

budget, contactProduct

Support.

Website:www.voscom.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Voscom Empfänger Handbücher

Voscom

Voscom VOS-2400FFT Series Bedienungsanleitung

Voscom

Voscom VOS-4FOM-D232T Series Bedienungsanleitung

Voscom

Voscom VOS-8040FDT Series Bedienungsanleitung

Voscom

Voscom VOS-2210FFDT Series Bedienungsanleitung

Voscom

Voscom VOS-2010FDT Series Bedienungsanleitung

Voscom

Voscom VOS-2FOM-D485T Series Bedienungsanleitung

Voscom

Voscom VOS-8810FFDT Series Bedienungsanleitung

Voscom

Voscom VOS-1HD-ADST Bedienungsanleitung

Voscom

Voscom VOS-8FOM-D232T Series Bedienungsanleitung

Voscom

Voscom VOS-1200FFT Series Bedienungsanleitung

Voscom

Voscom VOS-0200DT Series Bedienungsanleitung

Voscom

Voscom VOS-2410FFDT Series Bedienungsanleitung

Voscom

Voscom VOS-2200FDT Series Bedienungsanleitung

Voscom

Voscom VOS-1110FFDT Series Bedienungsanleitung

Voscom

Voscom VOS-0200FT Series Bedienungsanleitung

Voscom

Voscom VOS-2200FFT Series Bedienungsanleitung

Voscom

Voscom VOS-1HD-ADCET/R Series Bedienungsanleitung

Voscom

Voscom VOS-1DH3G-ADCEMT Bedienungsanleitung

Voscom

Voscom VOS-1FOM-SCCT Series Bedienungsanleitung

Voscom

Voscom VOS-1DHD-ADMT Bedienungsanleitung

Voscom

Voscom VOS-2FOM-DCCT Series Bedienungsanleitung

Voscom

Voscom VOS-1210FFDT Series Bedienungsanleitung

Voscom

Voscom VOS-0400DT Series Bedienungsanleitung

Voscom

Voscom VOS-4000FT Series Bedienungsanleitung

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Sherwood

Sherwood NewCastle R-772 Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Kramer

Kramer 631R Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung