Vynco VMOSS Bedienungsanleitung

INSTALLATION INSTRUCTIONS

VMOSS/VMOSSB - FLUSH MOUNT 360° CEILING SENSOR

ELECTRICAL SPECIFICATIONS

Supply Voltage Range 230 - 240V AC, 50Hz

Load Rating 2000W Incandescent

400W LED

450W Fluorescent

400W Motor/Fan

Operating Temperature 5°C - 40°C

Wire Size 1x 2.5mm²

2x 1.5mm²

Wiring 2.5mm2

TIMING AND LUX SPECIFICATIONS

Detection Method Passive Infrared (PIR)

Detection Angle 360°

Detection Range Ø 6m

Time Adjustment 5 secs - 30 mins

Lux Adjustment 10 - 2000Lux

Ceiling Cut-Out Size Ø 60mm

IP44

WARRANTY

This product is covered by the standard 3 year

Vynco Warranty - proof of purchase is required.

Please contact Vynco for details of returns

procedure.

NOTE: This product contains NO user

serviceable parts.

INSTALLATION

This product should be installed by a suitably

qualied person in accordance with Australian

and New Zealand Wiring rules.

INSTALLATION POSITION

Ideally the sensor should be positioned between

2.4 and 4m above the area to be scanned.

To avoid nuisance tripping,

installation should try to avoid areas:

1. With water features such as swimming pools

or ponds.

2. Near heat sources such as air conditioners,

dryers, re places or heaters.

3. Which are subject to direct bright

or reected lights or sunlight.

4. Which are frequented by animals,

such as pets or birds.

INSTALLATION PROCEDURE

STEP 1

Ensure desired location is suitable and clear of

all obstruction.

STEP 2

Ensure the relevant circuits are isolated and safe.

STEP 3

Cut out a 60mm diameter hole in the ceiling.

STEP 4

Unclip the wiring & terminal cover from the rear

of the sensor.

STEP 5

Connect the supply and load cables to the terminal

block as shown in the wiring diagram.

STEP 6

Replace the wiring & terminal cover.

STEP 7

Fold back installation springs and insert the sensor

into the cut out hole in the ceiling.

STEP 8

Twist the fascia cover off the sensor to access

the controls.

STEP 9

Set and test the controls as described in

the next section.

STEP 10

Replace fascia.

VYNCO.CO.NZ

AUCKLAND

9 Levene Place, Mount Wellington

PO Box 12 249, Penrose, Auckland 1061

New Zealand

P +64 9 525 6051

VYNCO INDUSTRIES (NZ) LIMITED

CHRISTCHURCH

388 Tuam Street, Phillipstown, Christchurch, 8011

PO Box 9022, Tower Junction, Christchurch 8149

New Zealand

P +64 3 379 9283

E [email protected]

VYNCO.CO.NZ

INSV0103

WIRING DIAGRAM SETTING THE CONTROLS

STEP 1

With the sensor fully installed.

STEP 2

Turn the time dial to the minimum (5 seconds)

and the lux dial to minimum (DAY).

STEP 3

Turn on power to the lights or load connected to the

sensor. The light or load may turn ON for a short

period (30 seconds) while the sensor warms up,

it will then turn off.

STEP 4

Walk through the coverage area, the lights

or load connected to the sensor should turn ON.

This conrms the wiring is correct and the light

or load is operational.

STEP 5

Adjust the time dial to your desired setting.

STEP 6

To set the ambient light level at which the sensor

will switch on, turn the lux dial to the minimum

(night). When the light in the room or area is at the

desired level, have someone walk continuously

through the detection zone as the lux dial is

increased. When the light or load connected to

the sensor turns ON release the dial.

STEP 7

If the installation is outdoors, refer to functional test

method for daylight hours,

FIELD VIEW OF DIAGRAM

FUNCTIONALITY TEST DURING DAYLIGHT PROCEDURE

STEP 1

Ensure correct wiring by a suitably qualied person

following the installation instructions provided with

the product.

STEP 2

Set lux and duration time to minimum

STEP 3

Using the VMOSS packaging, cover the sensor

completely. Covering the sensor will bypass the

surrounding lux sensitivity control and allow the PIR

to be activated. This check will ensure the load is

connected correctly and will turn on.

STEP 4

Adjust lux and the time dial to desired setting once

the sensor activation is conrmed.

The lux level in very bright areas or peak sunlight

may exceed the sensor’s maximum lux sensitivity

control of 2000 lux. This may cause the sensor

to not operate until its eld of detection darkens.

Dieses Handbuch passt für folgende Modelle

Andere Vynco Zubehör Handbücher

Vynco

Vynco VMOSS Gebrauchsanweisung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung