Wali M001LM Bedienungsanleitung
M001LM
WARNING
！！USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.
SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual.
Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect
assembly or inappropriate use.
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
Measure the thickness of your mounting surface or desk
Option A : Clamp Installation Option B: Grommet Base Installation
4A 4B
1 2
3
Single Monitor Desk Mount
75x75\100x100
VESA Plate
A (x1)
Arm
B (x1)
C-Clamp
C (x1)
Pole
D (x1) Pole Cover
E (x1)
Tool Holder
F (x1)
Grommet Base Plate
G (x1)
Anti-skid Pad
H (x5)
M6x12 Bolt
I (x3)
Support Plate
J (x1)
Top Screw
K (x1)
Allen Key 4mm
L (x1)
Allen Key 6mm
M (x1)
Allen Key 5mm
N (x1)
M4x12 Bolt
M-A (x4)
M4x16 Bolt
M-B (x4)
M5x12 Bolt
M-C (x4)
M5x16 Bolt
M-D (x4)
D5 Washer
M-E (x4)
Spacer
M-F (x4)
Fit clamp: 0.39”- 3.3”
Grommet: 0.39”- 3”
L
C-Clamp Brace
Clamp
L
I
D
H
L0.39”-3.3”
Hand knob
G
H
DE
Press Pole Cover Einto the top of Pole D.
1.Connect Pole Dand C-Clamp Brace from the bottom using M6x12 Bolt Iand tighten
with Allen Key 4mm L.Tear off the protect paper and attach Anti-Skid Pads Hto the
bottom designated position of C-Clamp Brace as image shown.
2. Connect C-Clamp to C-Clamp Brace using the bolts and tighten with Allen Key 4mm L.
Rotate the hand knob clockwise to fasten for stability.
1. Loosen the screw to release the hand
knob using a screwdriver as image shown.
(Screwdriver not included)
2. Tear off the protect paper and attach Anti-Skid
Pads Hto the bottom designated position of
Grommet Base Plate Gas image shown.
Loosen the bolts on C-Clamp Cusing Allen Key 4mm L.
INSTALLATION MANUAL
1-844-SATTLER (18447288537)
www.walielectric.com
8kg/17.6lbs
RATED
MAX 32”
TIPOVER WARNING
● NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
● USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.
Supplied Parts List
3a.Existing Grommet Hole Installation 3b.Self-drilled Grommet Hole Installation 5
10
6
8
7
G
D
0.39”-3”
ø 10mm
(ø ")3/8
J
B
D
F
M
B
K
M
F
M
L
M4x12 M5x12
Hand thread screws
into the threaded
inserts on the back of
your TV to determine
which screw diameter
(M4x12 or M5x12) to use.
M-C M-A
M-E M-E
A
M-E
M-F
M-B
M-D A
Mark the position of the hole on your mounting surface. Drill a 3/8"(10mm) diameter hole at
the marked position through the mounting surface. Place the Grommet Base Plate Gand
Pole Dto the grommet hole. Insert the hand knob through the center hole of Support Plate
Jand desk hole, rotate the hand knob clockwise to fasten for stability.
If the existing grommet hole comes with a plastic protector, remove it to ensure a flat surface
before installing the desk mount. Place the Grommet Base Plate Gand Pole Dto the
grommet hole. Insert the hand knob through the center hole of Support Plate Jand desk hole,
rotate the hand knob clockwise to fasten for stability.
Put the Tool Holder Fand Arm Bthrough the Pole D, adjust the preferred height and
tighten using Allen Key 6mm M.
Adjust the tilt angle using Allen Key 6mm M.
Put the assembled TV/Monitor onto the Arm Band ensure stability, tighten the VESA
plate using Top Screw K.
9Guide the cable through the Tool Holder Fand wire clips. Store the Allen Keys in the Tool
Holder F.
Manually swivel, tilt, and rotate the monitor for the best viewing angle.
0.39”-3”
J
G
D
Step 5.1
Select TV Screws
Step 5.2
Select Spacers ( if needed )
Step 5.3a
Step 5.3b
Select M4x12 Bolt M-A or M5x12 Bolt M-C according to your TV/Monitor, connect
VESA Plate Atogether with D5 Washer M-E into the mounting holes on the back of
TV/Monitor, tighten with a screwdriver. (Screwdriver not included)
Select M4x16 Bolt M-B or M5x16 Bolt M-D according to your TV/Monitor, connect
VESA Plate Atogether with D5 Washer M-E and Spacer M-F into the mounting
holes on the back of TV/Monitor, tighten with a screwdriver. (Screwdriver not included)
Flat Back Monitor
Curved Back Monitor
Andere Wali Rack & Stand Handbücher
Wali
Wali MF002XLS Bedienungsanleitung
Wali
Wali M002XL Bedienungsanleitung
Wali
Wali M00LP Bedienungsanleitung
Wali
Wali GPV002 Bedienungsanleitung
Wali
Wali MF001-P Bedienungsanleitung
Wali
Wali MATI002-G Bedienungsanleitung
Wali
Wali GSDM002 Bedienungsanleitung
Wali
Wali GSMP002 Bedienungsanleitung
Wali
Wali M003S Bedienungsanleitung
Wali
Wali GSMP001 Bedienungsanleitung
Wali
Wali 1343LKS Bedienungsanleitung
Wali
Wali M003 Bedienungsanleitung
Wali
Wali CS303 Bedienungsanleitung
Wali
Wali GSMP001W Bedienungsanleitung
Wali
Wali TVS001 Bedienungsanleitung
Wali
Wali PRS001 Bedienungsanleitung
Wali
Wali M001XL Bedienungsanleitung
Wali
Wali MF002LM Bedienungsanleitung
Wali
Wali 2655LO Bedienungsanleitung
Wali
Wali TVDVD-01 Bedienungsanleitung
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
