WANHAO Duplicator i3 Handbuch
WANHAO i3 UNBOXING AND
HARDWARE SET UP
Wanhao I3 unboxing and hardware set up. Rev.D 1 / 10
Unboxing and Hardware Setup
We packaged your Duplicator i3 very carefully at the Wanhao Bot cave -- we hope you’ll read this
guide and be just as careful unpacking it. In fact you should always be really careful with The
Duplicator i3. Here are a few things to keep in mind.
Safety In Safety Information formation
1.1 Caution: The Duplicator i3 generates high temperatures and includes moving parts that can
cause injury. Never reach inside The Duplicator i3 while it is in operation and allow time for The
Duplicator i3 to cool down after operation.
The Duplicator i3 is sensitive to electrostatic discharge. Make sure you don't have a static charge
on you by touching a grounded
object before operating The Duplicator i3 or attempting any adjustments. If opening The
Duplicator i3 for service ensure that the power supply is turned off and the cord is disconnected.
Package Contents
Here are the items that should be found in the Duplicator i3 package:
-The Duplicator i3
-Single Step exstruder MK10
-1x spool holder
-Hex Wrench and bolt Kit
- 1 x SD card
-2 x Wanhao platform tape
-10 meters PLA filament
-1 x Power supply cable
-1 x USB A to B cable
-1 x filament stand
Wanhao I3 unboxing and hardware set up. Rev.D 2 / 10
Unboxing
2.1 The Duplicator i3 is packed very tightly and carefully -- take your time unpacking it. In this
section the names of important parts of the machine will be in bold type.
First place The Duplicator i3's box on the work table next to a clean flat work space. Open from
the up side. Cut the plastic bag. So you can clear all the protection foam and cut all the white
secure ribbons.
1. Cut the ribbon 2. Get the spare parts box out
3.Take the foam out 4.Take off the box
Wanhao I3 unboxing and hardware set up. Rev.D 3 / 10
5. Put the Base onto a table or floor. Never drag the black cable.
6. Put the control box onto table or floor.
7. Stand the tower on the table take 8. Cut the white secure ribbon.
Of secure sticker on switch and wing nuts.
Wanhao I3 unboxing and hardware set up. Rev.D 4 / 10
9. Raise the right X axis manually. 10.Raise the left axis manually.
11.Insert the Base into the tower and match the bolt hole.
12. Lock the 2 bolts on left right side.
Wanhao I3 unboxing and hardware set up. Rev.D 5 / 10
13.Turn printer aside Lock extra 2bolts inside base 14. Lock the left motor cable
15. Cut the black ribbon 16.Short cable for Z; Long for X black for end stop switch
17. Connect end stop switch to socket switch directly onto it’s position. For some printer you may
need to install the switch onto the side wall.
18. 18. Insert the drag Chain into socket
Wanhao I3 unboxing and hardware set up. Rev.D 6 / 10
Note: the black cable is not a handle! Never lift The D plicator i3 by the black cable 2.3
In the packaging underneath your Duplicator i3 you’ll find the Power cable as well as your USB A
to B cable and Filament. Take these out and put them aside.
You should be able to see the build platform: it’s an aluminum plate. Tear off one Wanhao
Masking tape to cover the plate.
Wanhao I3 unboxing and hardware set up. Rev.D 7 / 10
You have now finished unpacking your Duplicator i3! We’re really proud of it! Also we
recommend that you keep the box that it was shipped in for future transport and long-term
storage.
The D plicator i3 Diagram
Before we continue let’s familiarize ourselves with some of the main features of The Wanhao
Duplicator i3.
3.1 Front:
1. Step exstruder MK10
2. Build Platform
3. LCD Interface Panel
5. SD Card slot (on side panel)
3.2 Back and side:
6. Power switch（110V or 220V）
7. Power input
8. USB cable input
9. spool holder
Initial Hardware Set p.
Now set the Spool holder on the control box. Insert 2 screws through the 2 holes of spool holder
stand. Lock the 2 screws onto the stand. Then insert the filament spool holder through the stand
hole and lock it by 2 plastic nuts.
Wanhao I3 unboxing and hardware set up. Rev.D 8 / 10
Almost finished! Check your Power Supply power switch. There are 2 voltage option, 110V and
220V. Make sure you are setting the switch at right voltage according to your local power supply
voltage. 4.6 Note:this is a 2 voltage Power Supply Unit which can accept 110V and 240 V AC at
50/60 hz. It also has a standard IEC cable input to accept international cable types if you’re out
side the China. Next plug the cable into the Power Supply socket next to the power switch.
4.7Before connecting anything make sure that the Duplicator i3 power switch is in the OFF
position and the switch is at right voltage of your local area.
To protect the motor cable from damage during shipping we have unplug the Z axis and X axis
motor cable connector. You need to insert the connector into the socket when you start. The
longest cable is for X axis. And the other 2 male connectors quite near the female connector are
for Z axis motor. Just insert them.
Wanhao I3 unboxing and hardware set up. Rev.D 9 / 10
Last open up your WANHAO filament(not included in the printer box) and mount them on the
Spool holder.
We do recommend to print from SD card only. If you need to update the firmware in future
locate the USB A to B cable and plug it into the USB B port on The Duplicator i3. Don’t plug the
other end into anything yet. For updating firmware check www.wanhao3dprinter.com
----software downloading.
Guess what? You’re done with initial hardware setup! Take a moment to relax and mentally
prepare yourself for what lies ahead.
When you’re ready to flip the switch and make your first prints head to the next step the First
Andere Handbücher für Duplicator i3
5
Inhaltsverzeichnis
Andere WANHAO 3D-Drucker Handbücher
WANHAO
WANHAO Duplicator 6 Bedienungsanleitung
WANHAO
WANHAO Duplicator 8 MARK I Bedienungsanleitung
WANHAO
WANHAO DUPLICATOR I3 MINI Bedienungsanleitung
WANHAO
WANHAO Duplicator i3 Merkblatt
WANHAO
WANHAO Duplicator 5S Bedienungsanleitung
WANHAO
WANHAO DUPLICATOR 9 Bedienungsanleitung
WANHAO
WANHAO Duplicator 10 Bedienungsanleitung
WANHAO
WANHAO Duplicator 5 Bedienungsanleitung
WANHAO
WANHAO MARK II Duplicator 6 Plus Bedienungsanleitung
WANHAO
WANHAO Duplicator 5S Bedienungsanleitung
WANHAO
WANHAO CGR Mini Mono Bedienungsanleitung
WANHAO
WANHAO GADOSO GR1 Bedienungsanleitung
WANHAO
WANHAO Duplicator i3 Bedienungsanleitung
WANHAO
WANHAO CGR Series Bedienungsanleitung
WANHAO
WANHAO D9 Bedienungsanleitung
WANHAO
WANHAO Duplicator 7 Plus Bedienungsanleitung
WANHAO
WANHAO DUPLICATOR 9 Bedienungsanleitung
WANHAO
WANHAO Duplicator 7 Plus Bedienungsanleitung
WANHAO
WANHAO D12 300 Bedienungsanleitung
WANHAO
WANHAO Duplicator 3/4 Bedienungsanleitung
