Wasp WLP 4170 Betriebsanleitung

Wasp WLP 4170 CCD

Programming Guide

Please Read

Note:

The Wasp WLP 4170 CCD Scanner is ready to scan the most

popular bar codes out of the box. This manual should only be

used to make changes in the configuration of the scanner for

specific applications. This scanner does not require software or

drivers to operate. The scanner enters data as keyboard data.

Please review this manual before scanning any of the programming

bar codes in this manual.

Tech Tip

If you are unsure of the scanner configuration or have scanned the

incorrect codes, please scan the default

bar code on page 6. This will reset the scanner to its

factory settings.

Version 1.0

No part of this publication may be reproduced or transmitted in

any form or by any means without the written permission of

Wasp Technologies. The information contained in this document

is subject to change without notice.

Wasp is a trademark of Wasp Technologies. All other trademarks or registered trademarks are the

property of their respective owners.

Table of Contents

Chapter 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Chapter 2. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Chapter 3. Quick Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Chapter 4. Bar Code Symbologies . . . . . . . . . . . . . . . . . . . . . . . .4

Chapter 5. Setup & Configuration . . . . . . . . . . . . . . . . . . . . . .5-34

1. Factory Default . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

2. Beep and Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

3. Intercharacter Delay . . . . . . . . . . . . . . . . . . . . . . . .8

4. Keyboard Wedge . . . . . . . . . . . . . . . . . . . . . . . . . . .9

5. Scanning Modes, Country Codes . . . . . . . . . . . . .10

6. Set Terminator/Preamble/Postamble Configuration . .11

5. Bar Code Symbology . . . . . . . . . . . . . . . . . . . .12-29

Code 39 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-13

Code 128 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-15

UPC-A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-17

UPC-E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18-19

EAN-13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-21

EAN-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22-23

Code 93 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Interleaved 2 of 5 . . . . . . . . . . . . . . . . . . . . . . . . .25

Codabar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26-27

MSI/Plessey . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

PDF417 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Appendix A Bar Code Test Symbols . . . . . . . . . . . . . . . . . . . .30-33

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Product Support, Warranty . . . . . . . . . . . . . . . . . . . .35

ASCII Code Table . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Chapter 1

Introduction

Bar coding is the most common Automated Data Collection (ADC) technology

providing timely, error-free information that can be used to increase productivity,

accuracy, and efficiency in the workplace. Virtually every type of industry is using

bar codes to replace keyboard data entry. Studies have shown that a proficient data

entry operator will make one error for every 300 characters that are manually

entered. The error rate using bar codes is almost negligible and can be

error-free using bar code symbologies with the check digit enabled.

The Wasp Charged Coupled Device (CCD) technology is a technique whereby

a bar code is photographed, digitized, and electronically sampled by built-in

photodetectors. The detectors process the measurement of every bar and space

using the number of adjacent photodetectors which contrast a black mark and a

white space. Wasp WLP 4170 CCD is extremely rugged since it has no moving

parts. Wasp WLP 4170 CCD reader supports PC AT/XT and PS/2 keyboard

interfaces and easily wedges between the computer and keyboard. Bar code data

is passed directly into the keyboard buffer as if it had been typed in by hand by a

data entry operator.

Of all the hand held bar code scanning devices on the market, the CCD reader is

the easiest to use and most cost effective for the typical business user. To activate

the scanner, the user simply points the scanning aperture towards the bar code,

pulls the trigger, and aims the red LED beam across the bar code.

1. Turn off your computer.

2. Unplug your PC keyboard cable and plug the male end (Din 5) of the Wasp

WLP 4170 CCD Scanner directly into your PC keyboard port. Plug your

keyboard cable into the other end (female Din 5) of the the Wasp WLP 4170

CCD Scanner. If your keyboard and PC support a Din 6 connection, use the

enclosed Din 5 to Din 6 converter cable to connect to the keyboard power

tap cable.

3. Turn your computer on.

Chapter 2

Installation

Keyboard

Y-Cable

Din-5F

Din-6M

Scanning Aperture

Your Wasp WLP 4170 CCD Scanner is ready to go. The default settings of the

Wasp WLP 4170 CCD Scanner have been pre-programmed for the most common

bar code configurations. Use the "Setup & Configuration" sections only to

customize the Wasp settings.

Tip: Use the pre-printed "Bar Code Test Symbols" in Appendix A on page 30 as a

test chart to begin practicing scanning.

Chapter 3

Quick Start

KEYBOARD

Y-CABLE

WLP 4170 CCD SCANNER

BACK OF PC

KEYBOARD MOUSE

DO NOTPLUG

IN MOUSE PORT!

KEYBOARD

Bar codes are symbols consisting of a series of bars and spaces which can be

applied to packages, cartons, bottles, and other commercial products. The bars

and spaces in each symbol are grouped in such a way to represent a specific ASCII

character or function. The interpretation of these groups is based on a particular

set of rules called symbologies. Various symbologies have been developed for

particular applications. Some examples are shipping and receiving, manufacturing,

retail, healthcare, transportation, document processing and tracking, and libraries.

The resolution of a bar code is dependent on the narrowest element of a bar code

(X dimension), and can vary from high density (nominally less than 0.009 in./0.23

mm), medium density (between 0.009 in./0.23 mm and 0.020 in./0.50 mm), and

low density (greater than 0.020 in./0.50 mm). Medium and low densities are the

most common since these are the easiest to read (scan) with nearly all scanning

devices. Wasp WLP 4170 CCD Scanner can read bar codes with X-dimensions as

low as 4 mils (0.10mm).

Wasp WLP 4170 CCD Scanner can read the most popular linear bar code

symbologies including Code 39, Code 93, Code 128, Interleaved 2 of 5, UPC-A,

UPC-E, EAN/JAN-8, EAN/JAN-13, Codabar, and MSI Plessey, and also the 2D bar

code symbology PDF417.

Please see test chart on pages 30-33.

Chapter 4

Bar Code Symbologies

In order to configure Wasp WLP 4170 CCD Scanner, you must familiarize yourself

with the setup procedures on the following pages. The default settings of Wasp

WLP 4170 CCD Scanner are identified on each page and clearly marked using an

asterisk (*). The default settings have been preprogrammed for the most

common bar code configurations. Use the Setup & Configuration only to

customize the Wasp settings. If you need to configure Wasp WLP 4170 CCD

Scanner, the default settings will be overwritten. All the programmed settings are

stored permanently in non-volatile memory. Therefore, your configuration will be

maintained even if keyboard power to Wasp WLP 4170 CCD Scanner is removed

by turning off your PC.

In order to configure Wasp WLP 4170 CCD Scanner, seven basic steps need to be

followed for each programmed setting:

(1) Determine what, if any, options on EACH PAGE that you wish to change.

(2) Scan the "Begin" bar code. WLP 4170 CCD Scanner will sound an ascending

tone to indicate that setup is in progress.

(3) Scan the bar code representing the option to be changed.

(4) Scan the bar codes representing the option values (e.g. 01, 02, 3A etc.).

These option values can be found on the inside back cover flap of this manual.

You must scan two digits for each option setting.

(5) Repeat the above two steps, if necessary, to change the options in the

same group.

(6) Scan the “Finish” bar code on the back cover flap to confirm your selections.

(7) Scan the "Exit" bar code to exit the group currently selected.

Wasp WLP 4170 CCD Scanner will sound a descending tone.

NOTE: Pages 6 and 7 are designed as walk through example pages. Use these

pages as examples on how to change an option for the rest of the manual.

Chapter 5

Setup & Configuration

Chapter 5

Factory Default

NOTE: Scanning these bar codes returns the scanner to the

factory default settings

1. Scan “Begin ”

2. Scan “Default” to restore

scanner to default settings

Tip: Use this configuration to restore the factory default settings if you are unsure

how your scanner has been configured. The 'Factory Default' configuration is very

useful when you need to reprogram your Wasp

WLP 4170 CCD Scanner after the defaults have been changed. By setting

the default configuration, the user knows precisely the configuration for each

programmed setting.

Begin

Default

Chapter 5

Beep Volume Settings

00 None

01 Lowest

02 Low

03 Medium (Default)

04 Medium-High

05 High

06 High-Medium

07 Highest

The 'Beep Volume' configuration changes the volume of the audible indicator of

the WLP 4170 CCD Scanner.

NOTE: For help in configuring these settings, consult the programming steps on

page 5.

1. Scan “Begin ”

2. Scan “Set Beep Volume”

4. Scan the “Finish” barcode on

the back cover flap

5. Scan the “Exit” barcode

3. Pick a setting from the table at

right, then turn to the back cover

flap and scan the corresponding

two digits. For example: if you

desire no beep, scan 0 and 0 on

the back cover flap

Begin

Set Beep Volume

Exit

Beep and Delay

Andere Handbücher für WLP 4170

Inhaltsverzeichnis

Andere Wasp Barcode-Lesegerät Handbücher

Wasp

Wasp WRS100SBR Bedienungsanleitung

Wasp

Wasp WWS650 Installations- und Betriebshandbuch

Wasp

Wasp WDI4200 Bedienungsanleitung

Wasp

Wasp WPS1500 Bedienungsanleitung

Wasp

Wasp WLR8900 Betriebsanleitung

Wasp

Wasp 2D Bedienungsanleitung

Wasp

Wasp WWS800 Handbuch

Wasp

Wasp WWS800 Bedienungsanleitung

Wasp

Wasp Wasp WDI7500 Bedienungsanleitung

Wasp

Wasp WDI9600 Bedienungsanleitung

Wasp

Wasp WWR2900 Betriebsanleitung

Wasp

Wasp WWS650 Bedienungsanleitung

Wasp

Wasp CCD - 80SIR Bedienungsanleitung

Wasp

Wasp WPL304 Bedienungsanleitung

Wasp

Wasp Bar Code Laser Betriebsanleitung

Wasp

Wasp WWS500 Betriebsanleitung

Wasp

Wasp WPL608 Bedienungsanleitung

Wasp

Wasp WLR8950 Bedienungsanleitung

Wasp

Wasp WPL205 Bedienungsanleitung

Wasp

Wasp WWS550i Installationsanleitung

Wasp

Wasp WLS8600 Bedienungsanleitung

Wasp

Wasp WLR8950 Bedienungsanleitung

Wasp

Wasp WLS9600 Installations- und Betriebshandbuch

Wasp

Wasp WLS 9500 Bedienungsanleitung

Beliebte Barcode-Lesegerät Handbücher anderer Marken

POSMicro

POSMicro Datalogic PowerScan D7100 Bedienungsanleitung

Marson

Marson MT780 Kurzanleitung zur Einrichtung

NCR

NCR RealPOS Bedienungsanleitung

Motorola

Motorola SE3300 Kurzanleitung zur Einrichtung

Element

Element P130BT Bedienungsanleitung

Motorola

Motorola Symbol LS3008 Installations- und Betriebshandbuch

Meec tools

Meec tools OBD-II / VAG Bedienungsanleitung

SICK

SICK CLP 100 Bedienungsanleitung

Royal Tag SA

Royal Tag SA I-Read Bedienungsanleitung

Welch Allyn

Welch Allyn IMAGETEAM 3800 Bedienungsanleitung

Meteor

Meteor 8310 Bedienungsanleitung

Denso

Denso BHT-500B Bedienungsanleitung

Datalogic

Datalogic Heron HD3130 Bedienungsanleitung

Motorola

Motorola MP6000 Montageanleitung

Newland

Newland NLS-HR15-BT Bedienungsanleitung

ARTDEV

ARTDEV AS-1310 Bedienungsanleitung

Aopos

Aopos AS290 Bedienungsanleitung

ENS

ENS 367-5455 Bedienungsanleitung