Wattstopper PW-100 Bedienungsanleitung

Santa Clara, CA 95050

800.879.8585

Installation Instructions

Specifications

Voltages:

PW-100 & PW-200. . . . . . . . . . . . . . . . 120/277VAC, 50/60Hz

PW-100-347 & PW-200-347. . . . . . . . . . . . 347VAC, 50/60Hz

Load Limits for each relay:

@120VAC.............0-800W tungsten or ballast, 1/6 HP

@277VAC.............................0-1200W ballast

@347VAC.............................0-1500W ballast

Load Type Compatibility:

Incandescent, fluorescent, magnetic or electronic ballast

Horsepower Rating (each relay) .........1/6 HP @120VAC

Time Delay Adjustment ....................5 to 30 minutes

Walk-Through Mode.. 3 minutes if no activity after 30 sec.

Test Mode...... 5 sec. for 10 min. with DIP switch setting

PIR Adjustment ...................High or Low (DIP switch)

Light Level Adjustment ......................8fc to 180+fc

Alerts ......................Selectable Audible & Visual

US Patents: 5640113, 6617560

PW-200 PW-200-347

PW-100 PW-100-347

PW-100/PW-100-347/PW-200/PW-200-347

Passive Infrared Wall Switch

Occupancy Sensor

UNIT DESCRIPTION AND OPERATION

The PW Passive Infrared Wall Switch sensors use advanced passive infrared

(PIR) technology.

The PW sensor can turn a load on, and hold it on as long as the sensor

detects occupancy. After no movement is detected for the selected time delay,

the lights switch off. A “walk-through” mode can turn lights off after only 3

minutes, if no activity is detected after 30 seconds following an occupancy

detection.

The PW-100 has one relay and one ON/OFF button. The PW-200 contains

two relays and two ON/OFF buttons to allow control of one or two loads

independently. Pressing a button toggles the state of the corresponding relay.

PW sensors contain a light level sensor. If adequate daylight is present, the

sensor holds the load OFF until light levels drop, even if the area is occupied. In

the PW-200, light level only affects the load on Relay 2. Users can overrule the

hold OFF function by pressing the ON/OFF button. See Light Level Adjustment.

Turning Load(s) ON (ON Mode)

The relays are programmed independently for either Auto ON or Manual ON. In

either mode, the load can be turned ON or OFF using the ON/OFF button.

Manual ON

DIP 8 ON

for Relay 1

DIP 9** ON

for Relay 2

With an ON Mode DIP switch in the ON position, the occupant

must press the ON/OFF button to turn ON the load. The sensor

keeps the load ON until no motion is detected for the selected

time delay. There is a 30 second re-retrigger delay. If occupancy

is detected during the delay, the sensor turns the load back ON.

After the re-trigger delay elapses the ON/OFF button must be

pressed to turn ON the load.

** PW-100: Switch 9 is not used. PW-200: Switch 9 default is ON to comply

with CA Energy Commission Title 24 bi-level switching requirements.

Auto ON

DIP 8 OFF for

Relay 1

DIP 9** OFF

for Relay 2

With an ON Mode DIP switch in the OFF position, the load turns

ON and OFF automatically based on occupancy. If the load is

turned OFF manually, Presentation Mode operation applies. This

prevents the load from turning ON automatically after it was

deliberately turned OFF. Pressing the button to turn lights ON

returns the sensor to Auto ON mode.

Shading indicates default operation and switch setting.

Model # Relay Default ON Mode DIP switch # Setting

PW-100 1 Manual ON 8 ON

PW-100-347 1 Manual ON 8 ON

PW-200 1 Auto ON 8 OFF

2 Manual ON 9 ON

PW-200-347 1 Auto ON 8 OFF

2 Manual ON 9 ON

Test/20 min

(DIP 1, 2, 3, OFF)

Presentation Mode is a feature of the Auto ON mode.When both relays are

manually turned OFF the PW holds the lights OFF until no motion has been

detected for the duration of the Time Delay. With subsequent occupancy, the PW

turns the load ON. If both relays are ON and one relay is manually turned OFF

this relay remains OFF until both the Time Delay and retrigger delay expires for

the relay that is ON, after that time the ON Mode control settings again apply.

Time Delays

The PW sensor holds the load ON until no motion is detected for the selected

time delay. Select the time delay using DIP switch settings. In the PW-200, both

relays use the same delay.

A Test Mode with a short time delay of 5 seconds is

set when DIP switches 1, 2, & 3 are OFF. It cancels

automatically after ten minutes, or when you set a

fixed time delay. When the Test Mode times out, the

sensor assumes a 20 minute time delay. To restart

Test Mode, change the time delay setting to any fixed

amount and then return it to the Test setting.

Walk-Through

Mode

(DIP #4 ON)

The PW sensor turns the load OFF three minutes after

the area is initially occupied, if no motion is detected

after the first 30 seconds. If motion continues beyond

the first 30 seconds, the set time delay applies.

High (DIP #5 OFF)Default setting. Suitable for most applications.

PIR Sensitivity Adjustment

The PW sensor constantly monitors the controlled environment and

automatically adjusts the PIR to avoid common ambient conditions that can

cause false detections, while providing maximum coverage.

Fixed Time Delay

(DIP 1 ON, 2 & 3 OFF)

Time delays are 5, 10, 15, 20 (default), 25, or 30

minutes.

Reduces sensitivity by approximately 50%. Useful in

cases where the PIR is detecting movement outside of

the desired area (also consider masking the lens) and

where heat sources cause unnecessary activation.

Low, 50%

(DIP #5 ON)

Visit our website for FAQs: www.wattstopper.com

Walk-Through

The Walk-Through mode shortens the time delay to reduce the amount of time

the load is ON after a brief moment of occupancy, such as returning to an office

to pick up a forgotten item then immediately exiting.

No Walk-Through

(DIP #4 OFF)

Walk-Through mode disabled.

Call 800.879.8585 for Technical Support

COVERAGE PATTERNS

Coverage testing has been

performed according to the

NEMA WD 7 guideline. For best

performance, use in spaces not

larger than 15’ x 12’.

PIR Sensor

The sensor has a two-tiered,

multi-cell viewing Fresnel lens with

180 degree field of view. The red

LED on the sensor flashes when the

PIR detects motion.

Masking the lens

Opaque adhesive tape is supplied

so that sections of the PIR sensor’s

view can be masked. This allows

you to eliminate coverage in

unwanted areas. Since masking

removes bands of coverage,

remember to take this into

account when troubleshooting

coverage problems.

PIR

Coverage

7.5’

(2.2m)

15’

(4.5m)

20’

(6.1m)

35’

(10.6m)

Major motion

Minor motion

Alerts

The PW can provide audible and/or visible alerts as a warning before the load

turns OFF.

Unit will beep at one minute*, at 30 seconds and at 10

seconds before turning OFF load. When Walk-Through

is active, the unit beeps three times at 10 seconds

before the load goes OFF.

*If Visible Alert is also ON, the one-minute time-out

warning beep is replaced by the visible alert.

Audible Alerts

(DIP #7 ON)

No audible warnings provided.

When only one minute is left in the time delay, the

load connected to the relay turns OFF for one second.

This provides a one minute warning before the load(s)

are turned OFF by the sensor.

Visible Alert

(DIP #6 ON)

No Visible Alerts

(DIP #6 OFF)

No visible warnings provided.

No Audible Alerts

(DIP #7 OFF)

4’

(1.2m)

20’

(6.1m)

35’

(10.6m)

Top View

Side View

1. Make sure that the power has been turned OFF at the circuit breaker.

2. Connect wires to the PW flying leads as shown in the

wiring diagram that is appropriate to the PW model and

electrical supply. The 2 ground wires (green and green/

yellow) must be fastened to ground for the sensor to

work properly.

3. Attach the sensor to the wall box by inserting screws into

the two wide holes on the top and bottom of the attached

metal bracket. Match them up with the

holes in the wall box and tighten.

4. Turn the circuit breaker ON. Wait one

minute, then push the Auto ON/OFF switch

for each load and the lights will turn ON.

There is a delay due to initial power-up

of the sensor that only occurs during

installation.

5. Test and adjust the sensor if necessary.

6. Install industry standard decorator wall

switch cover plate (not included).

INSTALLATION

Neutral

Blue

Line Black

Secondary

Load

Brown

Primary

Load

Red

Ground

Ground Green/Yellow

Green

Blue

Primary

Load

Secondary

Load

Neutral

Red

Brown

Line 2

Line 1 Black

Neutral

Ground

Ground Green/Yellow

Green

PW-200 and PW-200-347

Bi-Level Wiring

PW-200 and PW-200-347

Dual Circuit Wiring

WARNING

TURN THE POWER OFF AT THE CIRCUIT BREAKER

BEFORE INSTALLING THE SENSOR OR WORKING ON THE LOAD.

#12 – #14 AWG

Cu Wire Only

Strip Gage

1/2"

12.7mm

Visit our website for FAQs: www.wattstopper.com

Load

Red

Line Black

Neutral

Ground

Green

Ground

Green/Yellow

PW-100 and PW-100-347 Wiring

DELAY

PIR 50%

WALK

AUD. ALERT

RLY 1 MAN

RLY 2 MAN

VIS. ALERT

ON/OFF Buttons

Relay 1

Relay 2

DIP Switches

PIR Lens

Detection LED

DIP SWITCH SETTINGS

=ON =OFF

Auto On

Manual On

Relay 1 Mode

High

Low, 50%

PIR Sensitivity

Disabled

Enabled

Audible Alert

Disabled

Enabled

Walk-Through

12345678

Time

Delay

Walk-Through

Relay 1 Mode

Relay 2 Mode

Audible Alerts

PIR Sensitivity

Visible

Alerts

Test/20 min

10 minutes

15 minutes

20 minutes

25 minutes

30 minutes

Service

5 minutes

123

Time Delay

Service bypasses occupancy

& light level functions. Control the

load manually using ON/OFF button.

Disabled

Enabled

Visible Alert

PW-200 ONLY

Auto On

Manual On

Relay 2 Mode

Factory Settings:

All models

PW-100 series

PW-200 series

Call 800.879.8585 for Technical Support

Button

Hinges

Tabs

PW-200 shown.

PW-100 has a

single button.

TROUBLESHOOTING

Lights do not turn ON with motion (LED does flash)

1. Press and release each button to make sure that the correct lights come

ON for each relay. If the lights do NOT turn ON, check wire connections,

especially the Load connection. If the lights turn ON, verify that the

correct On Mode is selected in DIP switches 8 and 9.

2. Check to see if light level control is enabled: cover the sensor lens with

your hand. If the lights come ON, adjust the light level setting.

3. If lights still do not turn ON, call 800.879.8585 for technical support.

Lights do not turn ON with motion (LED does not flash)

1. Press and release each button to make sure that the correct lights come

ON for each relay. If the lights turn ON, verify that Sensitivity is on High.

2. Check the wire connections, in particular, the Line connection. Verify that

connections are tightly secured.

3. If lights still do not turn ON, call 800.879.8585 for technical support.

ADJUSTMENTS

Sensor Adjustment

Remove the wall plate. Remove the button cap by firmly squeezing together the

top sides of the button assembly. Gently pull it away from the unit.

When the adjustments are completed, replace the button cap by inserting its

hinges into the tabs on the main unit and then squeeze the top of the button while

pressing it into the unit. Reinstall the cover plate.

Light Level Adjustment

The light level can be set with loads ON or OFF. To enable light level control and

set the threshold: 1) Make sure the room is lit appropriately. 2) Put the sensor

into TEST mode (see Time Delay switches). You have 5 minutes to complete the

procedure. 3) Press and hold the ON/OFF button (Relay 1button on the PW-200)

for 3 seconds, until you hear a beep. 4) Step away from the sensor. After 25

seconds a beep sounds, indicating that the threshold level is set. This threshold

is retained, even if power is lost, until it is re-set or disabled. In the PW-200, light

level control only affects Relay 2.

To disable light level control, press and hold the Relay 1button for 7 seconds,

until a double beep tone sounds.

Reset to Default

Use the DIP Switch Settings tables on the previous page to return features

to factory settings. To reset the PW press and hold the Relay 1button for 10

seconds, until a triple beep sounds. This resets the sensor and disables light

level control (the brightest ambient light will not hold the light OFF).

Please

Recycle

2800 De La Cruz Boulevard, Santa Clara, CA 95050

Technical Support: 800.879.8585 • www.wattstopper.com

Warranty Information

WattStopper warranties its products to be free of defects in materials and

workmanship for a period of five years. There are no obligations or liabilities

on the part of WattStopper for consequential damages arising out of or in

connection with the use or performance of this product or other indirect

damages with respect to loss of property, revenue, or profit, or cost of removal,

installation or reinstallation.

Lights do not turn OFF

1. There can be up to a 30 minute time delay after the last motion is

detected. To verify proper operation, set DIP switch 1 to ON, then reset

switches 1, 2, and 3 to OFF to start Test Mode. Move out of view of the

sensor. The lights should turn OFF in approximately 5 seconds.

2. Verify that the sensor is mounted at least six feet (2 meters) away from

any heating/ventilating/air conditioning device that may cause false

detection. Verify that there is no significant heat source (e.g., high

wattage light bulb) mounted near the sensor.

3. If the lights still do not turn OFF, call 800.879.8585 for technical support.

Sensing motion outside desired areas

1. Select PIR Sensitivity – Low (DIP switch 5 = ON) if necessary.

2. Mask the PIR sensor’s lens to eliminate unwanted coverage area.

Red LED is lit all the time and the sensor features don’t work.

1. Check DIP switches 1,2,3. If they are all ON the unit is in Service Mode.

Set the DIP switches to a valid Time Delay setting.

2. If re-setting the Time Delay switches does not clear the LED call

technical support.

COVER PLATES

WattStopper PW series wall switches fit behind industry standard

decorator-style switch cover plates. Cover plates are not included.

Units come in the following colors, which are indicated by the final suffix

of the catalog number (shown here in parentheses):

White (-W), Light Almond (-LA), Ivory (-I), Grey (-G), Black (-B).

07124r6 8/2012

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere wattstopper Zubehör Handbücher

wattstopper

wattstopper CH-250 Bedienungsanleitung

wattstopper

wattstopper EW-100-120 Bedienungsanleitung

wattstopper

wattstopper DT-300 Bedienungsanleitung

wattstopper

wattstopper RD‑250 Bedienungsanleitung

wattstopper

wattstopper DT-305 Bedienungsanleitung

wattstopper

wattstopper CI-355 Bedienungsanleitung

wattstopper

wattstopper LMPX-100-4 Bedienungsanleitung

wattstopper

wattstopper LMPW-102 Bedienungsanleitung

wattstopper

wattstopper LMDC-100 Bedienungsanleitung

wattstopper

wattstopper RH-250 Bedienungsanleitung

wattstopper

wattstopper LMLS-400 Bedienungsanleitung

wattstopper

wattstopper LMLS-600 Bedienungsanleitung

wattstopper

wattstopper DT-200 Bedienungsanleitung

wattstopper

wattstopper FS-705 Bedienungsanleitung

wattstopper

wattstopper Legrand FM-105 Bedienungsanleitung

wattstopper

wattstopper DW 100 Bedienungsanleitung

wattstopper

wattstopper CI-200 Series Bedienungsanleitung

wattstopper

wattstopper CI-300 Bedienungsanleitung

wattstopper

wattstopper CX-100 Bedienungsanleitung

wattstopper

wattstopper HBP-111 Bedienungsanleitung

wattstopper

wattstopper PW-103N Bedienungsanleitung

wattstopper

wattstopper EW-200-120 Bedienungsanleitung

wattstopper

wattstopper EW-205-24 Bedienungsanleitung

wattstopper

wattstopper RH-250-W Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

wattstopper PW-100 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken