Wayne-Dalton 523 Bedienungsanleitung

WHEN INSTALLATION

IS COMPLETE PLEASE

LEAVE THIS MANUAL

WITH THE END USER!

INSTALLATION INSTRUCTIONS

SECURITY SHUTTER

MODEL 523

READ THESE INSTRUCTIONS THOROUGHLY

BEFORE ATTEMPTING TO INSTALL THIS DOOR!

Warnings & Safety Information................... 2

Key Drawing ..................................................... 3

Maintenance Instructions ............................ 4

Pre-Installation Checks & Tasks................... 5

Face of Wall Installation............................. 6-9

Between Jamb Installation.................. 10-13

Motor wiring and Limit Setting ......... 14-16

Warranty.............................................................17

TABLE OF CONTENTS

SAFETY INFORMATION

OVERVIEW OF POTENTIAL HAZARDS

READ THIS SAFETY INFORMATION

Overhead doors are large, heavy objects that move with the help of springs under high tension and electric motors. Since moving objects, springs under tension, and

electric motors can cause injuries, your safety and the safety of others depend on you reading the information in this manual. If you have questions or do not understand the

information presented, call your nearest trained door system technician.

In this section, and those that follow, the words Danger, Warning, and Caution are used to emphasize important safety information. The word:

DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION indicates a potentially hazardous situation which, if not avoided, may result in injury or property damage.

The word NOTE is used to indicate important steps to be followed or important considerations.

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

Potential Hazard Eect Prevention

MOVING DOOR

WARNING

Could result in Death

or Serious Injury

Keep people clear of opening while Door is moving.

Do NOT allow children to play with the Door Operator.

Do NOT operate a Door that jams or one that has a broken spring.

ELECTRICAL SHOCK

WARNING

Could result in Death

or Serious Injury

Turn OFF electrical power before wiring switch and motor to supply.

HIGH SPRING TENSION

WARNING

Could result in Death

or Serious Injury

Do NOT try to remove, install, repair or adjust springs or anything to which door spring parts are fastened, such as,

wood blocks, steel brackets, cables or other like items.

Installations, repairs and adjustments must be done by a trained door system technician using proper tools and

instructions.

Security Shutter with parts.

Right hand door is illustrated. Guides for face of wall mounting shown.

Please note that components and component locations are shown here for REFERENCE ONLY. Your unit

installation and component locations may be dierent.

CURTAIN

GUIDE

COVER

GUIDE

ASSEMBLY

STOPPER

ALL APPLICATIONS)

(NOT NEEDED IN

STANDOUT TUBE

ALL APPLICATIONS)

(NOT NEEDED IN

GUIDE

CURTAIN

HEAD

CURTAIN

COVER

GUIDE

WRAP

CURTAIN

STANDOUT TUBE

CURTAIN

STOPPER

HOOD

FASCIA PLATE

(ONLY USED WITH

BETWEEN JAMB

MOUNT)

KEY DRAWING

A sample of the “DOOR INSTALLATION DATA”sheet is shown here. Locate the work

order “Door Installation Data” sheet inside the door hardware box. You will need to

refer to the “Door Installation Data” sheet. See FIG 2.

Factory order number on door components must match with factory order number

on the “Door Installation Data” sheet. Each door has it’s own individual sheet.

DOOR INSTALLATION DATA SHEET

FIG 2

SAMPLE

Verify that the door installation can be accomplished before proceeding:

• Locate the work order “DOOR INSTALLATION DATA” sheet, see FIG 2, inside the door hardware box.

• Does the wall opening shown in FIG 3 match the Opening Width and Height shown on the“Door

Installation Data” sheet?

• Are the guides you received suitable for the jambs? Compare the guides type shown on the “Door

Installation Data” sheet with FIG 4.

• Can the guides be installed plumb?

• Check the sill for level. If sill is not level, mark the high sill location on the low side jamb.

• Guides are designed to rest on counter/sill.

Header

Opening

Height

Jamb

Sill

Opening Width

FIG 3

FACE OF WALL MOUNT

BETWEEN JAMB MOUNT

FIG 4

PRE-INSTALLATION CHECK LIST

CURTAIN

GUIDE

CURTAIN

GUIDE

JAMB

• Mount curtain guides to the wall surface using supplied fasteners. See FIG 5A and 5B.

• Check “G” Dimension as illustrated in FIG 4 on page 5. “G” Dimension must match your “DOOR INSTALLATION DATA” sheet.

• Both guides MUST be on a level line and both guides MUST be plumb.

• The “G”Dimension must be held within 1/8” over the entire height of the guides.

• If using the Cremone cylinder lock tubular bottom bar you will need to include the standout tubes between the guides and the wall as shown in FIG 5C. The standout

tubes will need to be pre-drilled onsite to match the holes in your curtain guide.

FIG 5A

• Lift the head assembly using a fork lift or other appropriate lifting equipment and lower it onto the top of the guides, inserting the support bars into the guide as shown

in FIG 6.

• Be sure the support bars are fully inserted into the guides on both sides. See FIG 7

• Install the wall fasteners provided into the head plate anges to attach it to the jamb. See FIG 7

FIG 7

CURTAIN

GUIDE

WALL

FASTENERS

FIG 5B

GUIDE

CURTAIN

WALL

FASTENERS

STANDOUT

TUBE

FIG 5C

SUPPORT

BAR

GUIDE

CURTAIN

HEAD

ASSEMBLY

FIG 6

SUPPORT BAR

FLANGE

HEAD PLATE HEAD PLATE

FLANGE

FULLY INSERTED

SUPPORT BAR

FULLY INSERTED

FACE OF WALL INSTALLATION

STEP 1STEP 1 INSTALL CURTAIN GUIDES TO JAMB

Follow instructions and use proper lifting equipment and correct lifting procedure to avoid serious injury or death.

WARNING WARNING

Rapidly closing curtain could result in death or serious injury. Do not remove factory binding around curtain assembly until step 3.

WARNING WARNING

STEP 2STEP 2 INSTALL HEAD ASSEMBLY

WINDING DIRECTION

(SOME COMPONENTS NOT

SHOWN FOR CLARITY)

CURTAIN

HEADPLATE

WRAP

GUIDE

CURTAIN

WINDING

NUT

FIG 8A

FIG 8B

HEAD

HOOD

ASSEMBLY

FLANGE

TOP

SCREWS

#10 TEK

WALL

FASTENERS

FIG 11

BOTTOM BAR

STOPPER

CURTAIN

GUIDE

FIG 10A

FIG 10B

Prior to winding or making adjustments to the springs, ensure you Are winding in the proper direction as stated in the Installation Instructions. Otherwise the spring

ttings may release from spring if not wound in the proper direction and could result in severe or fatal injury.

WARNING WARNING

Winding torsion spring(s) is an extremely dangerous procedure and should be performed only by a trained door system technician using proper tools and instructions.

WARNING WARNING

Rapidly closing curtain could result in death or serious injury. Use

caution when lowering curtain before spring tension is applied.

WARNING

• Cut the banding and carefully lower the curtain into the guides to

the fully closed position.

• Using a 1-1/2” open end wrench wind the spring by turning the

Winding Nut the specied number of turns indicated on your door

drawing sheet. The winding direction would be the same as the

direction to open the door for both left and right hand drive. See FIG

8A and FIG 8B.

• Check the balance of the door. If needed raise the door and adjust

the number of turns to achieve proper balance.

STEP 3STEP 3 WIND SPRINGS (SKIP THIS STEP IF YOUR DOOR IS

ELECTRICALLY OPERATED)

• Cut the banding and carefully lower the curtain into the guides to the fully

closed position.

• With door in the closed position attach stopper using stud plate and nuts

provided, as shown in FIG 10A and FIG 10B.

STEP 4STEP 4 ATTACH BOTTOM BAR STOPPER

• Position the hood in place as shown in FIG 11.

• Align the hood and attach using the #10 tek screws and wall fasteners

provided. See FIG 11.

• If your door is 12’-0” or wider you must also attach the hood to the hood

band, supporting the center of the hood with #10 tek screws provided.

STEP 5STEP 5 ATTACH FRONT HOOD

10/01/2015 356857 REV -

MOVING door could

result in death or

serious injury.

Do NOT close door

until doorway is clear.

1. Control the speed of the door

during manual operation.

2. Do not stand or walk under

moving door.

3. Keep doorway clear and in full

view while operating door.

4. Do NOT permit children to play

on, near, or with door or to

operate controls.

5. Unlock door before opening

door.

6. Sensing devices on motor

operated doors should be tested

frequently.

7. Adjustments or repairs must be

made by a trained door systems

technician using proper tools and

instructions.

8. Visually inspect door and

hardware monthly for worn

and/or broken parts and check to

see if door operates freely. DO

NOT operate a door with a

broken spring.

SAFETY INSTRUCTIONS

WARNING

Place label at a readable height

on door drive side guide or jamb.

Do NOT remove, cover, or paint

over label.

This label should be inspected

periodically for legibility, and a

replacement label should be

ordered from the door manufac-

turer as needed.

WARNING LABEL

GUIDE

COVER

GUIDE

COVER

GUIDE

FIG 12A

WARNING LABEL

FIG 12B

• Align guide covers on guides and snap into place. See FIG 12A.

• If needed guide covers can be removed using a at head screw driver.

STEP 6STEP 6 ATTACH GUIDE COVERS

• Place warning label on drive side guide at eye level. See FIG 12B

STEP 7STEP 7 PLACE WARNING LABEL

• If during previous step the door rolled up level and straight, skip this step.

A. Check that guides are plum, square, level, and are properly mounted onto oor and wall.

B. Check that the pipe is level.

C. Check that the attachment of the curtain is straight on the pipe.

If all of the above is correct and the door still rolls up out of level, a shim may need to be added, as shown in

FIG 13.

Shim materials:

• A piece of rubber is the desired material for a shim.

• A piece of cardboard could be used but may deteriorate over time.

• Use a 1/8” x 6” x 6” thick piece of material and increase thickness or pieces depending on the result

acquired, as shown in FIG 14.

Application of shim:

• To determine the side in which the shim will be applied, the door will need to be in the open position.

• When facing the door, the bottom bar will be unleveled. The lower side of the bottom bar will be the side

in which the shim needs to be placed.

• The hood may need to be loosened or removed for the application of the shim.

To apply the shim, two laborers might be required.

Installing the shim:

D. Close the door fully.

E. When door is at bottom make sure door is in hand chain mode.

F. Turn o the power to the motor (if applicable) to ensure safe application of the shim.

G. Backwind the door using the chain. Lock chain in place using chain keeper.

H. As the curtain is wound backwards apply the shim to the lower side between the pipe and slats or on

the ring of the low side.

I. Restore power to the motor (if applicable).

J. Check the level of the bottom bar while door is in the open position. If it is not level, add a second shim

and check again.

NOTE: If the door has wind locks there may be some stacking interference in the wind locks as the door is

wrapping during operation. This is a normal characteristic. For wind lock applications the doors bottom bar

should be level at the open position.

Bottom Bar Not Level

FIG 13

Shim

Curtain

RingPipe

FIG 14

STEP 8STEP 8 LEVEL DOOR (IF NEEDED)

When the door is wound backwards there is a force in which the door will want to wind forward. Secure the

door in this position by locking hand chain onto chain keeper to prevent injury.

WARNING

• If your door is equipped with a motor please refer to page 14 -16 for setup information and wiring.

STEP 8STEP 8 MOTOR OPERATION SETUP

SUPPORT

BAR

GUIDE

CURTAIN

HEAD

ASSEMBLY

FIG 15

GUIDE

CURTAIN

ASSEMBLY

HEAD

GUIDE

CURTAIN

JAMB

FIG 16

GUIDE

CURTAIN

FASTENERS

WALL

JAMB

CURTAIN

WRAP

FIG 17

FLUSH WITH

OUTER SURFACE

JAMB

WALL

FASTENER

CURTAIN

GUIDE

FIG 18

BETWEEN JAMB INSTALLATION

• Lift head assembly with fork lift and insert both support bars into curtain guides. See FIG 15

• Using the fork lift and two assistants, slide the whole assembly into place between the jambs until the guides are  ush with the jamb surface at the front of the door. See

FIG 16

• Check “G” Dimension as illustrated in Fig 4 on page 5.“G”Dimension must match your “DOOR INSTALLATION DATA” sheet.

• Both guides MUST be on a level line and both guides MUST be plumb.

• Be sure there is a small gap between the top of the headplates and the header for attaching the hood and fascia in a future step.

• The “Guide Dimension”must be held within 1/8” over the entire height of the guides.

• Mount curtain guides to the wall surface using supplied fasteners. See FIG 17 and 18

STEP 1STEP 1 INSTALL CURTAIN GUIDES AND HEAD ASSEMBLY

Follow instructions and use proper lifting equipment and correct lifting procedure to avoid serious injury or death.

WARNING WARNING

Rapidly closing curtain could result in death or serious injury. Do not remove factory binding around curtain assembly until step 2.

WARNING WARNING

Inhaltsverzeichnis

Andere Wayne-Dalton Garagentoröffner Handbücher

Wayne-Dalton

Wayne-Dalton IDrive 3651-372 Kurzanleitung

Wayne-Dalton

Wayne-Dalton 8500 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton Windload Post 9100 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 8124 Kurzanleitung

Wayne-Dalton

Wayne-Dalton 9100 Kurzanleitung

Wayne-Dalton

Wayne-Dalton 9700 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 9100 Technisches Dokument

Wayne-Dalton

Wayne-Dalton 8000 Series Kurzanleitung

Wayne-Dalton

Wayne-Dalton 8000 Series Kurzanleitung

Wayne-Dalton

Wayne-Dalton 8000 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 7100 Series Kurzanleitung

Wayne-Dalton

Wayne-Dalton TORQUEMASTER 6100 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 7400 Series Kurzanleitung

Wayne-Dalton

Wayne-Dalton DS-350 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 105 Kurzanleitung

Wayne-Dalton

Wayne-Dalton 8300 Kurzanleitung

Wayne-Dalton

Wayne-Dalton 800 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 523RX Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 8700 Kurzanleitung

Wayne-Dalton

Wayne-Dalton 9100 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 800FR Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 9605 Kurzanleitung

Wayne-Dalton

Wayne-Dalton TORQUEMASTER 6100 Kurzanleitung

Wayne-Dalton

Wayne-Dalton ThermoMark 5150 Bedienungsanleitung

Beliebte Garagentoröffner Handbücher anderer Marken

Dorma

Dorma ES 90 Bedienungsanleitung

Garaga

Garaga SECURITY+ 3265GCM 1HP Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive SECURITY+ WD822K Series Bedienungsanleitung

Chase Doors

Chase Doors DuraShield Bedienungsanleitung

CSI

CSI Classic Bedienungsanleitung

HATO

HATO 120 Bedienungsanleitung

Chamberlain

Chamberlain Elite 3575S Bedienungsanleitung

Richmond

Richmond GTR156 Bedienungsanleitung

Raynor

Raynor 1280RGD Bedienungsanleitung

CAME

CAME F4000 Series Bedienungsanleitung

B&D

B&D Controll-A-Door 5 Bedienungsanleitung

BFT

BFT PRV AA SL Bedienungsanleitung

Craftsman

Craftsman 139.53924 Bedienungsanleitung

Chamberlain

Chamberlain MyQ 940ESTD Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Bedienungsanleitung

Westfalia

Westfalia 19 36 07 Bedienungsanleitung

Chamberlain

Chamberlain HD520EVP Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung