25
26
27
28
81
19
18
72
41
22
20
23
23
15
10
10
14
Pins
18
41
60
27
27
16 6
Lubricate—80 20
51
21
12
25. Press a 1 1/2” Inner Cap (19) into the Leg Lever
(20).
Lubricate a 5/16” x 2 1/4” Bolt (80). Attach the
Leg Lever (20) to the Seat Frame (18) with the
Bolt and a 5/16” Jam Nut (81). Do not overtight-
en the Jam Nut; the Leg Lever must be able to
pivot freely.
Insert the 5/16” x 2” Eye Bolt (21) into the Leg
Lever (20) from the indicated side. Attach the Eye
Bolt with a 5/16” Flat Washer (5) and a 5/16”
Nylon Locknut (1).
26. Set the bracket on the Seat Frame (18) onto the
indicated pins on the Main Upright (41). Attach
the Seat Frame to the Main Upright with the 5/16”
x 2 3/4” Carriage Bolt (14) and the 5/16” Knob
(15).
Press 3/4” Round Caps (10) into the ends of both
Pad Tubes (22). Insert one Pad Tube into the
Seat Frame (18). Insert the other Pad Tube into
the Leg Lever (20).
Slide Foam Pads (23) onto the ends of both Pad
Tubes (22).
27. Attach the Backrest (72) to the Main Upright (41)
with the two 1/4” x 2 1/2” Screws (16) and two
1/4” Flat Washers (6).
28. Wet the ends of the Lat Bar (60) with soapy
water. Slide a 5” Grip (27) onto each end of the
Lat Bar.
9
15. Route the Low Cable (70) under the indicated
3 1/2” Thin Pulley (4). Be sure that the rubber
stop is on the indicated side of the Pulley.
Slide a 5/16” Flat Washer (5) and the 1/2” x 1 1/4”
Spacer (66) onto the 5/16” x 3 3/4” Bolt (49).
Insert the Bolt into the Main Upright (41), under
the indicated Pulley (4). Make sure that the
Cable is between the Spacer and the Pulley.
Slide another 5/16” Flat Washer (5) onto the Bolt,
and tighten a 5/16” Jam Nut (81) onto the Bolt.
16. Remove the two 3/8” x 1 3/4” Bolts (68), the two
3/8” Nylon Locknuts (2), and the two 3 1/2” Thin
Pulleys (4) from the “I” Plates (48).
Hold one of the 3 1/2” Thin Pulleys (4) in the indi-
cated loop of the High Cable (71). Reattach the “I”
Plates (48) to the Pulley with a 3/8” x 1 3/4” Bolt
(68) and a 3/8” Nylon Locknut (2).
Lay the Low Cable (70) over the other 3 1/2”
Pulley (4). Reattach the Pulley to the “I” Plates
(48) with a 3/8” x 1 3/4” Bolt (68) and a 3/8” Nylon
Locknut (2).
Route the end of the Low Cable (70) under the
indicated 3 1/2” Thin Pulley (4), between the
Pulley and the Cable Trap (69). Make sure that
the Cable Trap is in the 6 o’clock position.
Tighten the indicated 3/8” Jam Nut (82).
17. Note: The Large Pivot Bracket (52), the 5/16” x
3 1/4” Bolt (43), and the 5/16” Nylon Locknut
(1) shown in this step have been pre-attached.
Remove the parts from the Main Upright (41).
Lubricate the 5/16” x 3 1/4” Bolt (43). Re-attach
the Large Pivot Bracket (52) to the Main Upright
(41) with the Bolt and the 5/16” Nylon Locknut (1).
Do not overtighten the Nylon Locknut; the
Large Pivot Bracket must be able to pivot
freely.
