Weider Wedier Pro 9635 Bedienungsanleitung

USER'S MANUAL

QUESTIONS?

As a manufacturer, we are com-

mitted to providing complete

customer satisfaction. If you have

questions, or find that there are

missing or damaged parts, we

will guarantee you complete sat-

isfaction through direct assis-

tance from our factory.

TO AVOID UNNECESSARY

DELAYS, PLEASE CALL DIRECT

TO OUR TOLL-FREE CUSTOMER

HOT LINE. The trained techni-

cians on our customer hot line

will provide immediate assis-

tance, free of charge to you.

CUSTOMER HOT LINE:

1-800-999-3756

Mon.–Fri., 6 a.m.–6 p.m. MST

Model No. WESY96352

Serial No.

Write the serial number in the space

above for reference.

Serial Number Decal (Under Seat)

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. Save this manual

for future reference.

Visit our website at

www.weiderfitness.com

new products, prizes,

fitness tips, and much more!

TABLE OF CONTENTS

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

HOW TO USE THE HOME GYM SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

WEIGHT RESISTANCE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

TROUBLESHOOTING AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

CABLE DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached to the center of

this manual. Remove the PART IDENTIFICATION CHART and the PART LIST/EXPLODED DRAWING before

beginning assembly.

WEIDER is a registered trademark of ICON Health & Fitness, Inc.

IMPORTANT PRECAUTIONS

WARNING: To reduce the risk of serious injury, read the following important precau-

tions before using the home gym system.

WARNING: Before beginning this or any exercise program, consult your physician. This

is especially important for persons over the age of 35 or persons with pre-existing health problems.

Read all instructions before using. ICON assumes no responsibility for personal injury or property

damage sustained by or through the use of this product.

1. Read all instructions in this manual and in

the accompanying literature before using the

home gym system.

2. It is the responsibility of the owner to ensure

that all users of the home gym system are

adequately informed of all precautions.

3. The home gym system is intended for home

use only. Do not use the home gym system

in any commercial, rental, or institutional set-

ting.

4. Use the home gym system only on a level

surface. Cover the floor beneath the home

gym system to protect the floor.

5. Make sure all parts are properly tightened

each time you use the home gym system.

Replace any worn parts immediately.

6. Keep children under 12 and pets away from

the home gym system at all times.

7. Never release the press arm, butterfly arms,

military press arm, leg lever, leg press plate,

lat bar or nylon strap while weights are

raised. The weights will fall with great force.

8. Keep hands and feet away from moving parts.

9. Do not use the VKR station when either

weight stack is in use.

10. Always wear athletic shoes for foot protec-

tion.

11. Always stand on a foot plate when perform-

ing an exercise that could cause the home

gym system to tip.

12. Keep your hands away from the leg press

upright when the military press arm is being

used. Your hand could become pinched

between the leg press upright and military

press arm.

13. Make sure that the cables remain on the pul-

leys at all times. If the cables bind while you

are exercising, stop immediately and make

sure that the cables are on all of the pulleys.

14. Always disconnect the lat bar from the home

gym system when performing an exercise

that does not use the lat bar.

15. If you feel pain or dizziness at any time while

exercising, stop immediately and begin cool-

ing down.

BEFORE YOU BEGIN

ASSEMBLED

DIMENSIONS:

Height: 76 in.

Width: 89 in.

Length: 64 in.

Foot Plate

Low Pulley

Station

High Pulley Station

Lat Bar

Leg Lever

Butterfly Arms

Military Press Arm

Press Arm

Weight Stacks

Backrests

VKR Arms

Leg Press

Plate

Thank you for selecting the versatile WEIDER®PRO

9635 Home Gym System. The PRO 9635 offers a

selection of weight stations designed to develop every

major muscle group of the body. Whether your goal is

to tone your body, build dramatic muscle size and

strength, or improve your cardiovascular system, the

PRO 9635 will help you to achieve the specific results

you want.

For your benefit, read this manual carefully before

using the WEIDER®PRO 9635 Home Gym System.

If you have additional questions, please call our

Customer Service Department toll-free at 1-800-999-

3756, Monday through Friday, 6 a.m. until 6 p.m.

Mountain Time (excluding holidays). To help us assist

you, please note the product model number and serial

number before calling. The model number is

WESY96352. The serial number can be found on a

decal attached to the WEIDER®PRO 9635 (see the

front cover of this manual).

Before reading further, please review the drawing

below and familiarize yourself with the parts that are

labeled.

ASSEMBLY

1. Before beginning assembly, be sure that

you have read and understand the infor-

mation in the box above.

Locate and open the parts bag labeled

“FRAME ASSEMBLY.”

Press two 2” Square Outer Caps (51) onto

the indicated locations on the Stabilizer (5).

Press a 2” Square Inner Cap (27) into the

end of the Base (4).

Insert six 5/16” x 2 1/2” Carriage Bolts (1) up

through the Stabilizer (5). Insert two 5/16” x

2 1/2” Carriage Bolts up through the Base

(4).

Attach the Base (4) to the Stabilizer (5) with

two 5/16” x 2 3/4” Bolts (11), two 5/16” Flat

Washers (8), and two 5/16” Nylon Locknuts

(3). Do not tighten the Nylon Locknuts

yet.

FRAME ASSEMBLY

Before beginning assembly, carefully read the

following information and instructions:

•Place all parts of the PRO 9635 in a cleared area

and remove the packing materials; do not dis-

pose of the packing materials until assembly is

completed.

• The assembly is broken into five stages: 1) frame

assembly, 2) press and butterfly arm assembly,

3) cable and pulley assembly, 4) seat and back-

rest assembly, and 5) VKR assembly. The hard-

ware for each stage is packaged separately.

• Wait until you begin each assembly stage to open

the parts bag labeled for that assembly stage.

•For help identifying the small parts used in

assembly, use the PART IDENTIFICATION

CHART located in the center of this manual.

Note: Some small parts may have been pre-

attached for shipping. If a part is not in the parts

bag, check to see if it has been pre-attached.

•As you assemble the PRO 9635 be sure that all

parts are oriented as shown in the drawings.

•Tighten all parts as you assemble them, unless

instructed to do otherwise.

THE FOLLOWING TOOLS (NOT INCLUDED) ARE

REQUIRED FOR ASSEMBLY:

• Two (2) adjustable wrenches

• One (1) standard screwdriver

• One (1) phillips screwdriver

• One (1) rubber mallet

• Lubricant, such as grease or petroleum jelly,

and soapy water will also be needed.

Assembly will be more convenient if you have the

following tools: A socket set, a set of open-end or

closed-end wrenches, or a set of ratchet wrenches.

2. Slide the VKR Upright (74) and the Leg Press

Upright (56) onto the indicated 5/16” x 2 1/2”

Carriage Bolts (1) in the Stabilizer (5). The

high side of the brackets on the VKR

Upright and Leg Press Upright should be

on the side shown. Hand-tighten four 5/16”

Nylon Locknuts (3) onto the Carriage Bolts.

Do not tighten the Nylon Locknuts yet.

Press two 2” Square Inner Caps (27) into the

Leg Press Upright (56). Press a 2” Square

Inner Cap into the VKR Upright (74).

Attach the Rubber Bumper (91) to the Leg

Press Upright (56) with the #8 x 1/2” Self-tap-

ping Screw (87).

3. Slide the Front Upright (42) onto the 5/16” x

2 1/2” Carriage Bolts (1) in the Base (4).

Hand-tighten a 5/16” Nylon Locknut (3) onto

each Carriage Bolt. Do not tighten the

Nylon Locknuts yet.

Press a 1” Square Inner Cap (6) into the

Front Upright (42).

High Sides

of Brackets

FRAME ASSEMBLY

4. Press a 2” Square Inner Cap (27) into the end

of the Top Frame (55). Press a 1 3/4” Square

Inner Cap (44) into each end of the crossbar

on the Top Frame. Press two 1” Round Inner

Caps (49) into the top of the crossbar.

Attach the Top Frame (55) to the VKR Upright

(74) and the Leg Press Upright (56) with two

5/16” x 2 3/4” Bolts (11) and two 5/16” Nylon

Locknuts (3).

Attach the Top Frame (55) to the Front

Upright (42) with two 5/16” x 2 3/4” Bolts (11),

two 5/16” Flat Washers (8), and two 5/16”

Nylon Locknuts (3).

5. Slide the Rear Seat Frame (100) onto the

indicated 5/16” x 2 1/2” Carriage Bolts (1) in

the Stabilizer (5). Hand-tighten two 5/16”

Nylon Locknuts (3) onto the Carriage Bolts.

Attach the other end of the Rear Seat Frame

(100) to the Leg Press Upright (56) with two

5/16” x 2 3/4” Bolts (11), two 5/16” Flat

Washers (8), and two 5/16” Nylon Locknuts (3).

Attach the Handle (82) to the Rear Seat

Frame (100) with two 5/16” x 2 1/2” Carriage

Bolts (1) and two 5/16” Nylon Locknuts (3).

Tighten all Nylon Locknuts used in steps

1–5.

6. Set two Weight Bumpers (19) on the bracket

on the Base (4) as shown. Set two Weight

Bumpers (19) on the bracket on the Stabilizer

(5).

Stack eight Weights (25) onto each set of

Weight Bumpers (19). Be sure that the pin

grooves are all on the same side of each

stack of Weights.

Be careful not to tip either stack of

Weights (25) until step 8 is complete.

56 42

Crossbar

100

5—Bracket

4—Bracket

FRAME ASSEMBLY

Grooves

6Pin

Grooves

7. Press a Weight Tube Bumper (64) into the

end of a Weight Tube (63). Insert the Weight

Tube into the front stack of Weights (25). Be

sure that the pin on the Weight Tube is sit-

ting in the pin grooves in the top Weight.

Lubricate the inside of the holes in a Top

Weight (65). Set the Top Weight onto the front

stack of Weights (25). Insert both Long

Weight Guides (62) into the stack of Weights.

Be sure that the holes in the Weight

Guides are at the top, as shown.

8. Press a Weight Tube Bumper (64) into the

end of the other Weight Tube (63). Insert the

Weight Tube into the rear stack of Weights

(25). Be sure that the pin on the Weight

Tube is sitting in the pin grooves in the top

Weight.

Lubricate the inside of the holes in the other

Top Weight (65). Set the Top Weight onto the

rear stack of Weights (25). Insert both Short

Weight Guides (73) into the stack of Weights.

Be sure that the holes in the Weight

Guides are at the top, as shown.

7Holes

Lubricate

Pin Grooves

Holes

Lubricate

Pin Grooves

FRAME ASSEMBLY

9. Attach the upper ends of the Short Weight

Guides (73) to the Top Frame (55) with a 5/16”

x 6” Bolt (60), two 1/2” x 3/4” Spacers (61), and

a 5/16” Nylon Locknut (3).

Attach the upper ends of the Long Weight

Guides (62) to the Top Frame (55) with a 5/16”

x 6” Bolt (60), two 1/2” x 3/4” Spacers (61), and

a 5/16” Nylon Locknut (3).

10. Locate and open the parts bag labeled

“ARM ASSEMBLY.”

Be sure there is a Bushing (98) in each side of

the Stabilizer (5). Press a 2” Square Inner Cap

(27) into each end of the Leg Press Arm (96).

Lubricate a 3/8” x 3 1/4” Bolt (67). Attach the

Leg Press Arm (96) to the Stabilizer (5) with the

Bolt and a 3/8” Nylon Locknut (21). Do not over-

tighten the Nylon Locknut. The Leg Press

Arm must be able to pivot freely.

Align the welded tubes on the Leg Press Plate

(95) with one set of holes in the Leg Press Arm

(96). Attach the Leg Press Plate to the Leg

Press Arm with the Press Pin (97).

11. Press a 1” x 7/8” Plastic Bushing (90) onto

each welded spacer on the Press Frame (17).

Slide the Press Frame into place onto the Base

(4). Note: This will be a tight fit. The Plastic

Bushings should fit on each end of the indi-

cated tube in the Base. Make sure that the

pulleys are on the side shown.

Lubricate the 3/8” x 8” Bolt (59). Attach the

Press Frame (17) to the Base (4) with the Bolt

and a 3/8” Nylon Locknut (21).

1117 Pulleys

must be on

this side

59—Lubricate

Welded Spacers

Tube 90

FRAME ASSEMBLYARM ASSEMBLY

61 61

Welded

Tube

96 21

67—Lubricate

12. Press a 1” Round Inner Cap (49) into one of

the Press Arms (46). Press a 1 3/4” Square

Inner Cap (44) into the Press Arm.

Attach the Press Arm (46) to one side of the

Press Frame (17) with two 5/16” x 2 1/2” Bolts

(22) and two 5/16” Nylon Locknuts (3).

Assemble the other Press Arm (46) in the

same manner.

13. Identify the Right Arm (48) and the Left Arm

(47). Note the position of the welded bracket

on each Arm. Arm identification is very

important for step 14.

Attach a “V”-Pulley (50) and a Long Cable

Trap (31) to the Right Arm (48) with a 3/8” x

2 1/2” Bolt (86) and a 3/8” Nylon Locknut (21).

Do not tighten the Nylon Locknut yet.

Attach a “V”-Pulley (50) and a Long Cable

Trap (31) to the Left Arm (47) in the same

manner.

14. Lubricate both axles on the Top Frame (55).

Slide the Right Arm (48) onto the right axle.

Note: Be careful not to confuse the Right

Arm with the Left Arm (47); refer to step 13

to identify the Right Arm. Be sure that the

upper end of the Right Arm is behind the

indicated bracket on the Top Frame (55).

Tap two 1” Retainers (69) and a 1” Round

Cover Cap (70) onto the axle. Be sure that

the teeth on the Retainers bend toward the

Round Cover Cap, as shown in the inset

drawing.

Attach the Left Arm (47) in the same manner.

Press 1 3/4” Square Inner Caps (44) into the

lower ends of the Right and Left Arms (47,

48). Wet the lower end of each Arm with

soapy water. Slide a 10” Pad (45) onto the

lower end of each Arm.

13 86

Welded

Brackets

ARM ASSEMBLY

44 49

55 Bracket

Lubricate

Axle

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Weider Heim-Fitnessstudio Handbücher

Weider

Weider WEBE05921 Bedienungsanleitung

Weider

Weider D136 Bedienungsanleitung

Weider

Weider 9900i Einrichtungshandbuch

Weider

Weider MEDALLION M-305 Bedienungsanleitung

Weider

Weider WEBE29910 Bedienungsanleitung

Weider

Weider XP 800 WESY75742 Bedienungsanleitung

Weider

Weider PRO 270 L Bedienungsanleitung

Weider

Weider C132 Bench Bedienungsanleitung

Weider

Weider 184 Bench Bedienungsanleitung

Weider

Weider 215 Bench Kurzanleitung

Weider

Weider Pro 330 Bench Kurzanleitung

Weider

Weider 190 Tc Bench Benutzerhandbuch

Weider

Weider WESY78734 Bedienungsanleitung

Weider

Weider 244 Bench Kurzanleitung

Weider

Weider Master12 Position Bench Bedienungsanleitung

Weider

Weider WEEVSY3426.1 Bedienungsanleitung

Weider

Weider COBRA Bedienungsanleitung

Weider

Weider 831.153921 Bedienungsanleitung

Weider

Weider 3130 Bedienungsanleitung

Weider

Weider 9900i Bedienungs- und Wartungshandbuch

Weider

Weider PRO 3750 Bedienungsanleitung

Weider

Weider 7000x-train Bedienungsanleitung

Weider

Weider 170 Tc Bench Bedienungsanleitung

Weider

Weider C102 Bedienungsanleitung

Beliebte Heim-Fitnessstudio Handbücher anderer Marken

Horizon Fitness

Horizon Fitness OXFORD 6 Bedienungsanleitung

Energetics

Energetics Multi Trainer 5.1 Bedienungsanleitung

Matrix

Matrix MG-PL Series Bedienungsanleitung

Reebok

Reebok Tbr2i Bedienungs- und Wartungshandbuch

Pure Fitness

Pure Fitness 8526HE Bedienungsanleitung

Bowflex

Bowflex Sport 001-6961 Bedienungsanleitung

NordicTrack

NordicTrack E8200 Competition Bench Kurzanleitung

Body Solid

Body Solid GHYP-345 Bedienungsanleitung

Evo

Evo TAHOE 5105 Bedienungsanleitung

ParaBody

ParaBody 40 Bedienungsanleitung

JLL

JLL Ventus Pro Air Power Bedienungsanleitung

Trojan

Trojan Colorado 370 Bedienungsanleitung

Octane Fitness

Octane Fitness xRide xR650 Bedienungsanleitung

Precor

Precor Discovery Series Bedienungsanleitung

Insportline

Insportline RW600 Bedienungsanleitung

Stamina

Stamina 55-1532 Bedienungsanleitung

Tunturi

Tunturi R25 Bedienungsanleitung

CYBEX

CYBEX Jungle Gym 17000 Bedienungsanleitung