Weslo Cadence 55 Bedienungsanleitung

USER'S MANUAL

Serial Number Decal

Model No. WMTL19408

Serial No.

Version No. 0

QUESTIONS?

If you have questions, or if parts are

damaged or missing, PLEASE

CONTACT THE STORE WHERE

YOU PURCHASED THIS PROD-

UCT.

Electric Specifications:

120V ~ 60 Hz Type Y

Vendor:

Comercializadora Mexico

Americana, S. de R.L. de C.V.

Av. Nextengo No. 78

Col. Santa Cruz Acayucan

Del. Azcapotzalco

Mexico D.F., C.P. 02770

R.F.

www.iconservice.com

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. Save this manual

for future reference.

Visit our website at

www.weslo.com

new products, prizes,

fitness tips, and much more!

TABLE OF CONTENTS

IMPORTANTPRECAUTIONS .................................................................3

BEFOREYOUBEGIN .......................................................................5

ASSEMBLY ...............................................................................6

OPERATIONANDADJUSTMENT .............................................................9

HOWTOFOLDANDMOVETHETREADMILL ..................................................12

MAINTENANCEANDTROUBLESHOOTING ....................................................13

EXERCISEGUIDELINES ...................................................................15

ORDERINGREPLACEMENTPARTS ..................................................BackCover

Note: A PART IDENTIFICATION CHART, an EXPLODED DRAWING, and a PART LIST are located at the end of

this manual.

WESLO is a registered trademark of ICON IP, Inc.

WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read the

following important precautions and information before operating the treadmill.

IMPORTANT PRECAUTIONS

1. It is the responsibility of the owner to ensure

that all users of this treadmill are adequately

informed of all warnings and precautions.

2. Use the treadmill only as described.

3. Place the treadmill on a level surface, with at

least eight feet of clearance behind it and two

feet on each side. Do not place the treadmill

on any surface that blocks air openings. To

protect the floor or carpet from damage, place

a mat under the treadmill.

4. Keep the treadmill indoors, away from mois-

ture and dust. Do not put the treadmill in a

garage or covered patio, or near water.

5. Do not operate the treadmill where aerosol

products are used or where oxygen is being

administered.

6. Keep children under the age of 12 and pets

away from the treadmill at all times.

7. The treadmill should not be used by persons

weighing more than 250 pounds.

8. Never allow more than one person on the

treadmill at a time.

9. Wear appropriate exercise clothes when

using the treadmill. Do not wear loose clothes

that could become caught in the treadmill.

Athletic support clothes are recommended for

both men and women.

Always wear athletic

shoes; never use the treadmill with bare feet,

wearing only stockings, or in sandals.

10. When connecting the power cord (see page 9),

plug the power cord into a surge suppressor

(not included) and plug the surge suppressor

into a grounded circuit capable of carrying 15

or more amps. No other appliance should be on

the same circuit. Do not use an extension cord.

11. Use only a single-outlet surge suppressor that

meets all of the specifications described on

page 9. To purchase a surge suppressor,

please see your local electronics store.

12. Failure to use a properly functioning surge

suppressor could result in damage to the con-

trol system of the treadmill. If the control sys-

tem is damaged, the walking belt may change

speed, accelerate, or stop unexpectedly,

which may result in a fall and serious injury.

13. Keep the power cord and the surge suppres-

sor away from heated surfaces.

14. Never move the walking belt while the power

is turned off. Do not operate the treadmill if

the power cord or plug is damaged, or if the

treadmill is not working properly. (See MAIN-

TENANCE AND TROUBLESHOOTING on page

13 if the treadmill is not working properly.)

15. Read, understand, and test the emergency

stop procedure before using the treadmill (see

STEP-BY-STEP CONSOLE OPERATION on

page 10).

16. Never start the treadmill while you are stand-

ing on the walking belt. Always hold the

handrails while using the treadmill.

17. The treadmill is capable of high speeds.

Adjust the speed in small increments to avoid

sudden jumps in speed.

18. Never leave the treadmill unattended while it is

running. Always remove the key and unplug

the power cord when the treadmill is not in use.

19. Do not attempt to raise, lower, or move the

treadmill until it is properly assembled. (See

ASSEMBLY on page 6 and HOW TO FOLD

AND MOVE THE TREADMILL on page 12.)

You must be able to safely lift 45 pounds (20

kg) to raise, lower, or move the treadmill.

20. When folding or moving the treadmill, make

sure that the storage latch is fully closed.

21. Do not change the incline of the treadmill by

placing objects under the treadmill.

The decals shown here have been placed on the tread-

mill. If a decal is missing, or if it is not legible, please

go to www.iconservice.com and order a free replace-

ment decal. Apply the decal in the location shown.

Note: The decals are not shown at actual size.

22. Inspect and properly tighten all parts of the

treadmill regularly.

23. Never drop or insert any object into any

opening.

24. DANGER: Always unplug the power

cord immediately after use, before cleaning

the treadmill, and before performing the main-

tenance and adjustment procedures de-

scribed in this manual. Never remove the

motor hood unless instructed to do so by an

authorized service representative. Servicing

other than the procedures in this manual

should be performed by an authorized service

representative only.

25. This treadmill is intended for in-home use

only. Do not use this treadmill in any commer-

cial, rental, or institutional setting.

WARNING: Before beginning this or any exercise program, consult your physician. This

is especially important for persons over the age of 35 or persons with pre-existing health problems.

Read all instructions before using. ICON assumes no responsibility for personal injury or property

damage sustained by or through the use of this product.

SAVE THESE INSTRUCTIONS

HOW TO FOLD AND MOVE THE TREADMILL

HOW TO FOLD THE TREADMILL FOR STORAGE

Unplug the power cord. CAUTION: You must be able to

safely lift 45 pounds (20 kg) to raise, lower, or move the

treadmill.

1. Hold the metal frame firmly in the location shown by

the arrow at the right. CAUTION: To decrease the pos-

sibility of injury, do not lift the frame by the plastic

foot rails. Make sure to bend your legs and keep your

back straight. As you raise the frame, make sure to lift

with your legs rather than your back. Raise the frame

about halfway to the vertical position.

2. Move your right hand to the position shown and hold the

treadmill firmly. Using your left hand, pull the latch knob

to the left and hold it. Raise the frame until the catch is

past the latch pin. Slowly release the latch knob; make

sure that the latch pin is resting securely against the

catch.

To protect the floor or carpet from damage, place a

mat under the treadmill. Keep the treadmill out of di-

rect sunlight. Do not leave the treadmill in the stor-

age position in temperatures above 85° Fahrenheit.

HOW TO MOVE THE TREADMILL

Before moving the treadmill, convert the treadmill to the stor-

age position as described above. make sure that the latch

pin is resting securely against the catch.

1. Hold the handrails and place one foot against a wheel.

2. Tilt the treadmill back until it rolls freely on the wheels.

Carefully move the treadmill to the desired location. Never

move the treadmill without tipping it back. To reduce

the risk of injury, use extreme caution while moving

the treadmill. Do not attempt to move the treadmill

over an uneven surface.

3. Place one foot against a wheel, and carefully lower the

treadmill until it is in the storage position.

HOW TO LOWER THE TREADMILL FOR USE

1. See drawing 2 above. Hold the treadmill with your right hand as shown. Pull the latch knob to the left and hold

it. Pivot the frame down until it is past the latch pin.

2. See drawing 1 above. Hold the metal frame firmly with both hands, and lower it to the floor. CAUTION: To

decrease the possibility of injury, do not lower the frame by gripping only the plastic foot rails. Do not

drop the frame to the floor. Make sure to bend your legs and keep your back straight.

Latch

nob

Catch

Handrail

Wheel

Frame

ASSEMBLY

Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not

dispose of the packing materials until assembly is completed. Do not remove the long wire is inside the Right

Handrail until told to. Note: The underside of the treadmill walking belt is coated with high-performance lubricant.

During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping car-

ton. This does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the

lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires the included hex key and your own Phillips screwdriver , adjustable

wrench , and wire cutters .

Note: To identify small parts used during assembly, see the PART IDENTIFICATION CHART in the center of

this manual. Some parts may be preassembled. To avoid damaging plastic parts, do not use power tools

for assembly.

1. Attach the six Base Pads (19) to the bottom of the Base

(71) with six Base Pad Screws (42). Note: The Base

Pads may be preassembled.

2. Have a second person hold the Base (71) in the position

shown.

Identify the Right Handrail (6) which has a large hole near

the lower end.

Hold the Right Handrail (6) so that the bend is in the

position shown. Insert two Handrail Bolts (12) into the

bracket on the Right Handrail. Attach the Right Handrail

to the Base (71) with the Handrail Bolts, two Handrail

Washers (30) and two Nuts (17). Do not tighten the

Nuts yet.

Attach the Left Handrail (7) to the Base (71) in the same

way.

71 42

42 19

Large

Hole

Bend

5. Hold the Console (1) near the Right Handrail (6). Touch

the Right Handrail to discharge any static.

Untie the wire from the end of the Wire Harness (22).

Insert the end of the Wire Harness through the three

looped plastic ties. Next, press the end of the Wire

Harness into the connector on the back of the Console

(1) in the location shown. The end of the Wire Harness

should slide easily into the connector and snap into

place. If it does not, turn the end of the Wire Harness and

then insert it. IF THE CONNECTORS ARE NOT CON-

NECTED PROPERLY, THE CONSOLE MAY BE DAM-

AGED WHEN THE POWER IS TURNED ON. Plastic

Ties

Connector

4. Have a second person lift and hold the front end of the

Frame (55). Hold a Frame Spacer (13) between the Right

Handrail (6) and the Frame. Attach the Right Handrail to

the Frame with a Frame Bolt (10), a Handrail Washer

(30), and a Handrail Star Washer (60).

Repeat this step on the left side of the treadmill.

3. With the help of a second person, raise the Handrails

(6, 7) so the Base (71) is flat on the floor as shown.

Attach the Wheels (15) to the outer sides of the Base

(71) with two Wheel Bolts (14) and two Wheel Nuts (88)

as shown. Do not overtighten the Wheel Nuts; the

Wheels should turn freely.

Position the front of the treadmill Frame (55) between the

Handrails (6, 7) as shown. Next, locate the long wire in-

side of the lower end of the Right Handrail (see the inset

drawing). Tie the end of the wire securely to the end of

the Wire Harness (22). Then, pull the opposite end of the

wire until the end of the Wire Harness is extending from

the upper end of the Right Handrail.

88 15

Wire

9. Make sure that all parts are properly tightened before

you use the treadmill. eep the included hex key in a

secure place. The hex key is used to adjust the walking

belt (see page 14). To protect the floor or carpet, place a

mat under the treadmill.

8. Carefully lower the Handrails (6, 7) to the floor. Center the

Frame (55) between the Handrails, and tighten the four

Handrail Bolts (12). Then, raise the Handrails to the verti-

cal position.

See drawing 8a. Attach the Storage Latch Assembly (41)

to the Left Handrail (7) with two 16mm Screws (58).

Make sure that the Storage Latch Assembly is ori-

ented as shown.

See HOW TO CHANGE THE INCLINE OF THE TREAD-

MILL on page 11. Adjust the incline legs and insert

the incline pins into the incline legs.

7. Attach the Console Back (4) to the Console (1) with four

16mm Screws (58). Note that there is a slot in the side of

the Console Back for the wire—make sure that no wires

are pinched.

Slot

6. Set the Console (1) on the Right Handrail (6) and the Left

Handrail (not shown). Finger tighten four Console Screws

(70) (only two are shown) into the Console. After you

have started all four Console Screws, tighten them.

Insert the excess Wire Harness (22) down into the Right

Handrail (6). Tighten the three plastic ties around the Wire

Harness, and then cut off the ends of the plastic ties.

Plastic

Ties

6, 7

DIAGRAM OF THE CONSOLE

Clip

Note: If there is a sheet of clear plastic

on the console, remove the plastic.

STEP-BY-STEP CONSOLE OPERATION

Before operating the con-

sole, make sure that the

power cord is properly

plugged in (see page 9).

Next, locate the reset/off cir-

cuit breaker on the treadmill

frame near the power cord.

Make sure that the circuit breaker is in the reset posi-

tion.

Next, stand on the foot rails of the treadmill. Find the

clip attached to the key (see the drawing above), and

slide the clip securely onto the waistband of your

clothes. Then, insert the key fully into the console.

After a moment, the display will light. Important: In an

emergency situation, the key can be pulled from

the console, causing the walking belt to slow to a

stop. Test the clip by carefully taking a few steps

backward; if the key is not pulled from the console,

adjust the position of the clip.

Follow the steps below to operate the console.

Insert the key fully into the console.

A moment after the key is inserted, the display will

light.

Press the Digital Speed increase button to start

the walking belt.

A moment after the button is pressed, the walking

belt will begin to move at 1 mph. Hold the handrails

and begin walking. As you exercise, change the

speed of the walking belt as desired by pressing

the Digital Speed buttons. Each time a button is

pressed, the speed setting will change by 0.1

mph; if a button is held down, the speed setting

will change in increments of 0.5 mph.

CAUTION: Before operating the

console, read the following precautions.

• Do not stand on the walking belt when turn-

ing on the power.

• Always wear the clip (see the drawing

above) while operating the treadmill.

• Adjust the speed in small increments to

avoid sudden jumps in speed.

• To reduce the possibility of electric shock,

keep the console dry. Avoid spilling liquids

on the console and place only sealed water

bottles in the water bottle holders.

Reset

OPERATION AND AD USTMENT

THE PRE-LUBRICATED WALKING BELT

Your treadmill features a walking belt coated with high-

performance lubricant. IMPORTANT: Never apply sil-

icone spray or other substances to the walking

belt or the walking platform. Such substances will

deteriorate the walking belt and cause excessive

wear.

HOW TO PLUG IN THE POWER CORD

Your treadmill, like any other type of sophisticated

electronic equipment, can be seriously damaged by

sudden voltage changes in your homeʼs power.

Voltage surges, spikes, and noise interference can

result from weather conditions or from other appliances

being turned on or off. To decrease the possibility of

your treadmill being damaged, always use a surge

suppressor with your treadmill (see drawing 1 at

the right). To purchase a surge suppressor, please

see your locel electronics store.

Use only a single-outlet surge suppressor that is

UL 1449 listed as a transient voltage surge sup-

pressor (TVSS). The surge suppressor must have a

UL suppressed voltage rating of 400 volts or less

and a minimum surge dissipation of 450 joules.

The surge suppressor must be electrically rated for

120 volts AC and 15 amps. There must be a moni-

toring light on the surge suppressor to indicate

whether it is functioning properly. Failure to use a

properly functioning surge suppressor could result

in damage to the control system of the treadmill. If

the control system is damaged, the walking belt

may change speed, accelerate or stop unexpect-

edly, which may result in a fall and serious injury.

This product must be grounded. If it should malfunc-

tion or break down, grounding provides a path of least

resistance for electric current to reduce the risk of elec-

tric shock. This product is equipped with a cord having

an equipment-grounding conductor and a grounding

plug. Plug the power cord into a surge suppressor,

and plug the surge suppressor into an appropriate

outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

Important: The treadmill is not compatible with

GFCI-equipped outlets.

This product is for use on a nominal 120-volt circuit,

and has a grounding plug that looks like the plug illus-

trated in drawing 1 below. A temporary adapter that

looks like the adapter illustrated in drawing 2 may be

used to connect the surge suppressor to a 2-pole

receptacle as shown in drawing 2 if a properly

grounded outlet is not available.

The temporary adapter should be used only until a

properly grounded outlet (drawing 1) can be installed

by a qualified electrician.

The green-colored rigid ear, lug, or the like extending

from the adapter must be connected to a permanent

ground such as a properly grounded outlet box cover.

Whenever the adapter is used it must be held in place

by a metal screw. Some 2-pole receptacle outlet box

covers are not grounded. Contact a qualified elec-

trician to determine if the outlet box cover is

grounded before using an adapter.

DANGER: Improper connection

of the equipment-grounding conductor can

result in an increased risk of electric shock.

Check with a qualified electrician or service-

man if you are in doubt as to whether the

product is properly grounded. Do not modify

the plug provided with the product—if it will

not fit the outlet, have a proper outlet

installed by a qualified electrician.

Grounded Outlet Box

Grounding Plug

Surge Suppressor

Grounding Pin

Adapter

Lug

Metal Screw

Grounded Outlet

Grounding Pin

Andere Handbücher für Cadence 55

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Weslo Tretmühle Handbücher

Weslo

Weslo Cadence 200 Bedienungsanleitung

Weslo

Weslo WLTL85052 Bedienungsanleitung

Weslo

Weslo Cadence 6.0 Treadmill Bedienungsanleitung

Weslo

Weslo Cardio Stride 2.0 Treadmill Bedienungsanleitung

Weslo

Weslo CADENCE G 3.9 Bedienungsanleitung

Weslo

Weslo Cadence 300 Treadmill Systemhandbuch

Weslo

Weslo Cadence 21.5 Treadmill Bedienungsanleitung

Weslo

Weslo Cadence 4450 Bedienungsanleitung

Weslo

Weslo Cadence 600 Treadmill Bedienungsanleitung

Weslo

Weslo WLTL26080 Bedienungsanleitung

Weslo

Weslo Cadence 500 Treadmill Systemhandbuch

Weslo

Weslo Cadence 16.0 Cwl Treadmill Kurzanleitung

Weslo

Weslo Cadence 21.5 Treadmill Benutzerhandbuch

Weslo

Weslo Cadence 4.0 Bedienungsanleitung

Weslo

Weslo Cadence S 8 Bedienungs- und Wartungshandbuch

Weslo

Weslo Easy compact 2 treadmill Benutzerhandbuch

Weslo

Weslo WLTL29310.0 Bedienungsanleitung

Weslo

Weslo Cadence 3100 Bedienungsanleitung

Weslo

Weslo CADENCE 850 WETL85061 Bedienungsanleitung

Weslo

Weslo Cadence 6.9 Ery Treadmill Benutzerhandbuch

Weslo

Weslo Lyne 3500 Treadmill Kurzanleitung

Weslo

Weslo Cadence 215s Treadmill Bedienungsanleitung

Weslo

Weslo Cadence J3.7 Treadmill Bedienungsanleitung

Weslo

Weslo Cadence 700 Treadmill Bedienungs- und Wartungshandbuch

Beliebte Tretmühle Handbücher anderer Marken

Treadly

Treadly TREADLY 2 Bedienungsanleitung

HEALTH ONE

HEALTH ONE Walk Ro Bedienungsanleitung

NordicTrack

NordicTrack T7.5 S Bedienungsanleitung

Gold's Gym

Gold's Gym ADVANTAGE GGTL12920 Bedienungsanleitung

Merax

Merax MS282992 Bedienungsanleitung

FYTTER

FYTTER RU-2SX Bedienungsanleitung

Precor

Precor 903 Bedienungsanleitung

FitLogic

FitLogic freewill d225 Bedienungsanleitung

HOP-SPORT

HOP-SPORT ESTIMA HS-3200LB Bedienungsanleitung

Horizon Fitness

Horizon Fitness Adventure 5 Plus Bedienungsanleitung

Stamia

Stamia InMotion II Bedienungsanleitung

Smooth Fitness

Smooth Fitness EVO 3i Bedienungsanleitung

NordicTrack

NordicTrack NETL81810.0 Bedienungsanleitung

Schwinn

Schwinn 830/Journey 8.0 Bedienungsanleitung

Keys Fitness

Keys Fitness HealthTrainer HT-740T Bedienungsanleitung

Spirit

Spirit XT8 Bedienungsanleitung

NordicTrack

NordicTrack T 14.0 Treadmill Bedienungsanleitung

Master

Master F22 Bedienungsanleitung