Whalen SIG3IN1CGT Bedienungsanleitung

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.

PLEASE READ AND KEEP FOR FUTURE REFERENCE.

Whalen Furniture Mfg., Inc. Page 1 Factory No. 33-10944

Signa Gaming TheaterTM 3-in-1TM TV Stand

Model # SIG3IN1CGT

U.S. Patents 8,079,311 & 8,191,485 and other Patent Pending

This item is designed to be a 3-in-1 configuration. Please choose the option that best suits your

needs. DO NOT discard any of the hardware or parts that you will not use on your chosen option.

This will allow you to use this TV Console in different configurations at a later date, if desired.

ADULT ASSEMBLY REQUIRED

If you have any questions regarding assembly or if parts are missing, DO NOT return this

item to the store where it was purchased. Please call our customer service number and have

your instructions and parts list ready to provide the model name, part name or factory

number:

1-866-942-5362

Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday

Or visit our web site 24 hours a day, 7 days a week for product assistance at

www.whalenstyle.com

Or e-mail your request to parts@whalenfurniture.com

LOT NUMBER:

DATE PURCHASED: / /

Model # SIG3IN1CGT

Whalen Furniture Mfg., Inc. Page 2 Factory No. 33-10944

MANUFACTURER: Whalen Furniture Mfg., Inc.

CATALOG: Signa Gaming TheaterTM 3-in-1TM TV Stand (SIG3IN1CGT)

DATE OF MANUFACTURE: December 2012

MADE IN CHINA

1. Please read the Assembly Instructions prior to assembling this product.

2. Remove all hardware from the box and sort by size.

3. Check to see that all hardware and parts are present BEFORE assembling.

4. Ask a friend to assist you with the assembly of this furniture.

5. To avoid damage, assemble the product on a sturdy, level and protective surface.

6. Please wait until all steps are completed before fully tightening bolts.

7. Make sure all bolts are tightly fastened before the unit is used.

MAXIMUM RECOMMENDED WEIGHT LOADS

GENERAL INFORMATION

TIPS and TRICKS

This product is sold with a set of Tipping Restraint Hardware Kit. You must install the Tipping

Restraint Hardware between the wall and the TV console to prevent any accidents or

damages. When properly installed, this restraint can provide protection against the unexpected

tipping of the unit due to small tremors, bumps or climbing. The restraint is only a deterrent and

is not a substitute for proper adult supervision. Use of tip-over restraints may only reduce, but

not eliminate, the risk of tip-over.

FITS UP TO MOST 60” FLAT PANEL TVs

MAXIMUM LOAD 135 lb. (61.2 kg)

FITS UP TO MOST 60” FLAT PANEL TVs

WITHOUT SWIVELING BRACKET

MAXIMUM LOAD 135 lb. (61.2 kg)

MAXIMUM LOAD 50 lb. (22.6 kg)

THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH

FLAT PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND

WEIGHT LIMITS. NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT

PANEL TVS OR EQUIPMENT. TO AVOID INSTABILITY, PLACE FLAT PANEL TV IN THE

CENTRE OF THE UNIT; CRT TVS, IMPROPERLY POSITIONED FLAT PANEL TVS, OR FLAT

PANEL TVS OR OTHER EQUIPMENT THAT EXCEED RECOMMENDED SIZE AND WEIGHT

LIMITS COULD FALL OFF OR BREAK THE UNIT, CAUSING POSSIBLE SERIOUS INJURY.

MAXIMUM LOAD 15 lb. (6.8 kg)

Model # NVS3IN1CGT

Whalen Furniture Mfg., Inc. Page 3 Factory No. 33-10944

Parts and Hardware List

Please read completely through the instructions and verify that all listed parts are present

before beginning assembly.

A- Top Shelf Frame (1) B- Middle Shelf Frame (1) C- Bottom Shelf Frame (1)

D- Long Spine (1) D1- Short Spine (1)

E- Left Leg (1) F- Right Leg (1) G- Top Glass (1)

H- Middle Glass Shelf (1) I- Bottom Glass Shelf (1) J- Swiveling Bracket (1)

(Pre-attached)

K- Mounting Frame (1) L- Monitor Bracket (2) M- SSS Spine (1)

N- Sensor/Sound Shelf (1) O- Cable Wheel (2)

Model # SIG3IN1CGT

Whalen Furniture Mfg., Inc. Page 4 Factory No. 33-10944

Parts and Hardware List

Please read completely through the instructions and verify that all listed parts are present

before beginning assembly.

(1) Suction Cup (2) 1/2” Bolt (3) 3/4” Bolt (4) 1-1/4” Bolt (5) Lock Washer

(24+1 extra) (8+1 extra) (12+1 extra) (8+1 extra) (24+1 extra)

(6) Flat Washer (7) Concrete Anchor (8) 2-1/2” Lag Bolt (9) Large Flat Washer

(24+1 extra) (4) (4) (4+1 extra)

M4 Allen Wrench 3/16” Allen Wrench Touch-up Pen Tipping Restraint Hardware Kit (1)

(1) (1) (1) (Inside Plastic Bag)

TV Mounting Kit

M4 x 12 Bolt (4) M4 x 30 Bolt (4) M5 x 12 Bolt (4) M5 x 30 Bolt (4)

M6 x 12 Bolt (4) M6 x 35 Bolt (4) M8 x 16 Bolt (4) M8 x 40 Bolt (4)

M4 Lock Washer (4) M5 Lock Washer (4) M6 Lock Washer (4) M8 Lock Washer (4)

Large Spacer (4) Small Spacer (4) M4/M5 Flat Washer (8) M6/M8 Flat Washer (4)

Tools required: Allen Wrench (provided) and Phillips screwdriver (not provided).

Model # NVS3IN1CGT

Whalen Furniture Mfg., Inc. Page 5 Factory No. 33-10944

Assembly Instructions

NOTE: Please do not fully tighten all bolts until you finish assembling all parts. Once assembled,

go back and fully tighten all bolts. This will make the assembly easier.

1. Unpack the unit and confirm that you have all the hardware and required parts.

2. Choose the option suits your needs. For the Floating Swivel Mount option, select the Long

Spine (D). For the other two options, select the Short Spine (D1). Set the Spine back face down

on a scratch free surface, as shown.

3. Align and attach 3 Shelf Frames (A, B and C) to the Spine. Make sure the inside corner plates

on the shelf frames will face up when the unit is turned upright.

1-1/4” Bolt

(4 used in this step)

④

Lock Washer

(6 used in this step)

⑤

Flat Washer

(6 used in this step)

⑥

3/4” Bolt

(2 used in this step)

③

B/C

D/D1

Model # SIG3IN1CGT

Whalen Furniture Mfg., Inc. Page 6 Factory No. 33-10944

Assembly Instructions

4. Stand the unit upright.

5. Align and attach the Left Leg (E) to the Top Shelf Frame (A) by inserting two 1-1/4” Bolts (4)

with Washers (5 and 6) from inside the Shelf Frame through the pre-drilled holes on the side

rail into the threaded inserts on the Leg. Make sure that top rail of Leg is flush with the wooden

front rail of Top Shelf Frame. DO NOT tighten the bolts.

6. Secure the Left Leg (E) to the Lower Shelf Frame (B and C) using the 3/4” Bolts (3) with

Washers (5 and 6) through the end bracket holes into the Leg.

7. Repeat the last 2 steps with the Right Leg (F). Make sure the gaps between the wooden front

rail of Top Shelf Frame and Legs are equal. Loosen the Bolts on the wooden front rail and

adjust, if necessary.

1-1/4” Bolt

(4 used in this step)

④

3/4” Bolt

(6 used in this step)

③

Lock Washer

(10 used in this step)

⑤

Flat Washer

(10 used in this step)

⑥

Model # NVS3IN1CGT

Whalen Furniture Mfg., Inc. Page 7 Factory No. 33-10944

Assembly Instructions

8. Go back and tighten all Bolts with the provided M4 Allen Wrench.

9. In case of uneven floor, Floor Levelers are provided at the bottom of both Legs (E and F).

Simply tilt the unit back and raise or lower Floor Leveler by hand to correct tilting, as shown

above.

If you choose Table-top Console

configuration, continue to step 10.

If mounting TV with the Floating Swivel

Mount, skip ahead to PAGE 11.

Model # SIG3IN1CGT

Whalen Furniture Mfg., Inc. Page 8 Factory No. 33-10944

Assembly Instructions for Table-top Console

10.Attach 2 Cable Wheels (O) to the backside of the Short Spine (D1) with the 3/4” Bolts (3).

Tighten the Bolts with the provided M4 Allen Wrench.

11.The Cable Wheels (O) enable you to shorten, separate and route cables and cords. Using the

Cable Wheels you can create a system for routing cables through channels, between

components and to power sources without tangled mess or annoying signal interference.

3/4” Bolt

(4 used in this step)

③

Model # NVS3IN1CGT

Whalen Furniture Mfg., Inc. Page 9 Factory No. 33-10944

B/C

Assembly Instructions for Table-top Console

12.Put the Suction Cups (1) firmly into top holes and inside corner plates on 3 Shelf Frames (A, B

and C), as shown.

TIP: If a Suction Cup resists insertion, try pressing down on the middle of the cup with the

Allen Wrench while twisting it clockwise into the hole.

13.Place the Top Glass (G) and Glass Shelves (H and I) in place starting from the Bottom Glass

Shelf, as shown above. Make sure the glass shelf is properly centered. Push each glass shelf

all the way back against the Spine. Also, be sure to press down evenly and firmly each glass

shelf onto the Suction Cups to make sure they securely rest onto the Suction Cups.

NOTE: If a glass shelf is scratched, you can minimize the damage by using a BLACK marker

and filling in scratched area from underneath.

Suction Cup

(24 used in this step)

①

Model # SIG3IN1CGT

Whalen Furniture Mfg., Inc. Page 10 Factory No. 33-10944

Assembly Instructions for Table-top

Tools required: Allen Wrench (provided), Phillips screwdriver, Mallet, Power Drill, and 3/8” Drill Bit.

14.Position the assembled console at the desired location against a wall. Now, follow the

instructions printed on the plastic bag containing the Tipping Restraint Hardware to mount the

tipping restraint to the Spine and the wall.

NOTE: YOU MUST USE THIS TIPPING RESTRAINT TO ATTACH THIS UNIT TO THE

WALL, TO PREVENT FROM TIPPING, CAUSING ACCIDENTS AND/OR INJURIES.

15.The Console is now ready for use. Be sure to position your Flat Panel TV in the center of the

console.

NOTE: If you choose the Tilting Wall Mount configuration, proceed to PAGE 19.

Inhaltsverzeichnis

Andere Whalen Inneneinrichtung Handbücher

Whalen

Whalen WF24HVO Bedienungsanleitung

Whalen

Whalen WSWB72-ST-E Bedienungsanleitung

Whalen

Whalen Parker Series Bedienungsanleitung

Whalen

Whalen Emergent SPUS-EGDB Bedienungsanleitung

Whalen

Whalen Kellum WMFP54EC-26GR Bedienungsanleitung

Whalen

Whalen Hendricks Series Bedienungsanleitung

Whalen

Whalen Stetson SMSSDSK Betriebsanleitung

Whalen

Whalen Huntingdon EC-HU48D Bedienungsanleitung

Whalen

Whalen MainStays Parsons Bedienungsanleitung

Whalen

Whalen AVCBEC60-SMB Bedienungsanleitung

Whalen

Whalen Bayside CSCGLBST-4-UK-BL Bedienungsanleitung

Whalen

Whalen James SPCA-JA48D Bedienungsanleitung

Whalen

Whalen PROL-37 Bedienungsanleitung

Whalen

Whalen LWS60DCVAG Bedienungsanleitung

Whalen

Whalen WSLW30IFV Bedienungsanleitung

Whalen

Whalen ATD60H-13AX Bedienungsanleitung

Whalen

Whalen Sagemoor SAGE7PD-E Bedienungsanleitung

Whalen

Whalen LWS30DCVAG Bedienungsanleitung

Whalen

Whalen JCS110605-D Bedienungsanleitung

Whalen

Whalen Shelby 60in Bedienungsanleitung

Whalen

Whalen LWF30AVG Bedienungsanleitung

Whalen

Whalen BSKY-368036 Bedienungsanleitung

Whalen

Whalen XLDEC54-NV Bedienungsanleitung

Whalen

Whalen Sedona MNFP54BF23-5 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung