Wheaton GRAB SAMPLER 1 Bedienungsanleitung

Specifications subject to change without prior notice 1

WHEATON SCIENCE PRODUCTS

GRAB SAMPLER 1

INSTRUCTION MANUAL

CATALOG NUMBERS 990250

Wheaton Science Products

1501 N. 10th Street

Millville, NJ 08332-2093 USA

Tel: (800) 225-1437 / (856) 825-1100 Fax: (856) 825-1368

www.wheatonsci.com

Specifications subject to change without prior notice 2

WARRANTY

Wheaton Science Products warrants this product to be free from defects in material and workmanship for a period of

one (1) year from the date of shipment. If repair or adjustment is necessary within the warranty period and has not

been the result of mishandling or abuse, the unit may be returned prepaid, provided that return authorization has

been obtained. Wheaton Science Products will correct the defect or adjust the unit at no charge.

Items returned for repair or adjustment should be packed very carefully to prevent damage in transit and should also

be insured against carrier damage. Should the unit arrive damaged as a result of transit, a claim will need to be made

against the carrier. The shipping carton should not be discarded but retained until inspection by a representative of

the carrier is made.

Wheaton Science Products will repair or adjust out of warranty products at a nominal charge.

SAFETY SYMBOLS USED IN THIS MANUAL

A Danger symbol indicates attention to an operation, which could cause electrocution, severe injury, or death!

A Warning symbol indicates attention to an operation, which can cause operator injury, improper function of, or

damage to the equipment and possible problems with the process.

Specifications subject to change without prior notice 3

GENERAL SAFETY INSTRUCTIONS

NOTE: EVEN THE SAFEST EQUIPMENT CAN CAUSE INJURY IF THE USER IS CARELESS.

1. KNOW YOUR INSTRUMENT - Read the operating manual carefully. Learn the equipment's application and

limitations.

2. GROUND ALL EQUIPMENT - If electrical, this instrument is equipped with a grounding type plug. The

green/yellow conductor in the cord is the grounding wire and should never be connected to a live terminal.

3. AVOID DANGEROUS ENVIRONMENT - Electrical instruments designed to process liquids must be

operated with extreme caution. If liquid comes in contact with internal electrical components or wires, fire or

electrical shock may occur. Adequate surrounding workspace should be provided during use. Do not operate

electrical instrumentation in a combustible atmosphere.

4. WORK SURFACE- Keep well lighted. Be certain the work surface is clean, level and sturdy enough to support

the weight of the unit, particularly if it is to be filled with liquid.

5. WEAR PROPER APPAREL - Do not wear loose clothing, neckties or jewelry that might get caught in moving

parts. Non-slip footwear is recommended. Wear protective hair covering to contain long hair.

6. WEAR SAFETY GOGGLES - Wear safety goggles at all times. Everyday eyeglasses only have impact

resistant lenses; they are NOT safety glasses.

7. DON'T OVERREACH- Keep proper footing and balance at all times.

8. MAINTAIN INSTRUMENT WITH CARE - Keep screws tight and unit clean. Check periodically for worn or

damaged parts. Inspect the plug and cord before each use. Do not operate this instrument if there are signs of

damage.

9. AVOID ACCIDENTAL START UP - If electrical, always make sure the switch is in the "OFF" position before

plugging instrument into outlet.

10. DISCONNECT INSTRUMENT - Always disconnect the instrument from the power source before servicing.

11. DO NOT BLOCK COOLING VENTS IF PROVIDED

12. DO NOT OPERATE THIS EQUIPMENT IN ANY MANNER NOT SPECIFIED IN THIS MANUAL

13. KEEP THE OPERATING MANUAL FOR THE INSTRUMENT IN A SAFE PLACE NEAR THE

INSTRUMENT FOR QUICK AND EASY REFERENCE.

14. IT IS RECOMMENDED THAT A FIRE EXTINGUISHER ALWAYS BE LOCATED IN AREAS

WHERE ELECTRICAL INSTRUMENTS ARE BEING USED.

WSP-305

Specifications subject to change without prior notice 4

INTRODUCTION

The WSP Grab Sampler 1 is a subsurface water-sampling tool designed to obtain samples from spillways,

boats, docks, etc., without physical entry into the effluent. It is constructed of 72” x ¾” square aluminum tubing

with a gold alodine finish. The WSP Grab Sampler 1 provides two different size clamps for mounting various

size bottles up to 1000 ml. Typical uses include routine water sample collection for analysis ranging from

B.O.D. to the full range of priority pollutants. The WSP Grab Sampler 1 affords easy waterway access,

eliminates surface contamination and assists in conforming to procedures described in the U.S. E.P.A’s

“Handbook for Monitoring Industrial Wastewater”. A 1000 ml borosilicate glass sample bottle with Teflon

lined screw cap is included.

INSTRUMENT SET UP (refer to fig. A)

1. Select the bottle clamps (2) (3) which best fit the desired sample bottle.

2. Slide the clamp onto the bottle to a point midway between the bottle shoulder and heel and tighten by turning

thumbscrew clockwise.

3. Insert the rod end of the clamp into the hole provided at the base of the Grab Sampler with bottle cap facing

suction cup (7).

4. Align the bottle so that the suction cup, when applied to the cap, is centered on the cap. It should be noted that

the unit will still function properly even if there is a degree of misalignment between the suction cup and bottle

cap. Tighten the bottle clamp by turning the clamp knob (12) clockwise.

5. With a firm sharp motion, slide the pull rod (10) toward the bottle so that the suction cup adheres to the top of

the bottle cap.

6. The unit is now ready for sampling (See Sampling Procedure).

Specifications subject to change without prior notice 5

SAMPLING PROCEDURE

DANGER!

BEWARE OF OVERHEAD WIRES! DUE TO THE LENGTH OF THE GRAB SAMPLER, IT IS

POSSIBLE TO REACH AND CONTACT OVERHEAD HIGH VOLTAGE WIRES. EXTREME CARE

MUST BE TAKEN ESPECIALLY OVER BRIDGES AND EVEN IN REMOTE AREAS THAT ARE

NOWHERE NEAR ROADS. HIGH VOLTAGE WIRES CAN BE WITHIN EASY REACH OF THE

GRAB SAMPLER.

WARNING! WHEN SAMPLING HAZARDOUS LIQUIDS PROTECTIVE CLOTHING AND SAFETY

GOGGLES MUST BE WORN.

1. With the bottle aligned properly and the suction cup firmly applied to the top of the bottle cap, place the closed

bottle into sample stream at the desired level. Good sampling practices, as recommended by the Environmental

Protection Agency or state agency, should be followed. The bottle mouth should be oriented to face upstream.

2. Unscrew the bottle cap from the bottle by turning the pull knob (11) counterclockwise. Turn this knob as many

times as is necessary to ensure the bottle cap is completely unscrewed from the bottle.

3. Pull up on pull knob to totally remove the cap from the bottle mouth.

4. Allow the open bottle to remain submerged until the proper sample volume is collected.

5. With the bottle still submerged, push down on the pull knob and turn clockwise until the cap completely seals

the bottle.

6. Remove the collected sample from the stream.

7. Disengage suction cup from bottle cap.

8. Remove the full sample bottle from the bottle clamp by turning the thumbscrew counterclockwise and replace

with an empty bottle if desired. Tighten cap.

IMPORTANT! EVEN THOUGH THE GRAB SAMPLER 1 IS CONSTRUCTED OF HIGH

STRENGTH ALUMINUM ALLOY AND STAINLESS STEEL, HIGHLY CORROSIVE CHEMICALS

SHOULD BE AVOIDED.

Specifications subject to change without prior notice 6

WHEATON GRAB SAMPLER 1 – PARTS LIST (FIG. A)

ITEM NO. DESCRIPTION WHEATON NO. USE QTY.

11000 ML GRADUATED BOTTLE w/ TEFLON®LINED CAP 990477 1

2LARGE CLAMP I052533 1

3SMALL CLAMP I052532 1

4END CAP I051339 1

5MOUNTING BLOCK WL052531 1

6#10-32 SS SCREW I052320 2

7SUCTION CUP ASSEMBLY I051337 1

8SHAFT COUPLER I051336 1

9NYLINER I051338 4

10 PULL ROD I052534 1

11 PULL KNOB I051335 1

12 CLAMP KNOB I051334 1

13 MAIN ASSEMBLY I052530 1

14 RUBBER GRIP I052090 1

ACCESSORIES FOR USE WITH THE GRAB SAMPLER 1

CATALOG NO. 219820 - WSP 1000 ml Sample Bottle with Teflon Lined Screw Cap – 24/cs

Specifications subject to change without prior notice 7

WHEATONGRAB SAMPLER

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Wheaton Laborausrüstung Handbücher

Wheaton

Wheaton CRIMPenstein Technisches Handbuch

Beliebte Laborausrüstung Handbücher anderer Marken

Qiagen

Qiagen DML 3000 Bedienungsanleitung

Queensgate

Queensgate NANOSCAN OP400 Programmierhandbuch

Conviron

Conviron GEN1000-GE Bedienungsanleitung

Parr Instrument

Parr Instrument 4560 Bedienungsanleitung

IKA

IKA IC control Bedienungsanleitung

Integra

Integra DOSE IT Bedienungsanleitung

Agilent Technologies

Agilent Technologies 5800 ICP-OES Bedienungsanleitung

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Bedienungsanleitung

NI PXI-5422 Handbuch

Collomix

Collomix Aqix Bedienungsanleitung

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Bedienungsanleitung

Ocean Insight

Ocean Insight FLAME-NIR+ Bedienungsanleitung

Parker

Parker ALIGN-MG-NA Bedienungsanleitung

BD 644787 Bedienungsanleitung

DENTAURUM

DENTAURUM Compact Megaplus Bedienungsanleitung

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Bedienungsanleitung

VWR

VWR SAS Super IAQ Bedienungsanleitung

illumina

illumina MiSeqDx Bedienungsanleitung