White Rodgers NP100 Verdrahtungsschema

NP100 Non-Programmable Thermostat

Installation Instructions & User Guide

Congratulations on the purchase of your White-Rodgers™thermostat!

Save these instructions for future use!

Questions? Contact White-Rodgers

™

customer service at 1-877-654-9394

For Installation Help

1-877-654-9394

White-Rodgers.com

For Installation HelpFor Installation Help

For Installation Help

For Installation Hel

877

654

9394

877 654 9394

hite-Rod

0037-7264A

White-Rodgers

8100 West Florissant Avenue

St. Louis, MO 63136

111

ATTENTION: MERCURY NOTICE

This product does not contain mercury. However, this product may replace a

product that contains mercury. Mercury and products containing mercury must

not be discarded in household trash. Do not touch any spilled mercury. Wearing

non-absorbent gloves, clean up any spilled mercury and place in a sealed

container. For proper disposal of a product containing mercury or a sealed

container of spilled mercury, place it in a suitable shipping container.

Refer to www.White-Rodgers.com for location to send product containing

mercury.

These symbols are used throughout this User Guide.

Watch for them to identify:

Cautions

Tips

Part 1: Before Getting Started ...................................................... Page 2

1.1 Check package contents

1.2 Answer questions about source of heating in your home

1.3 Assemble tools

1.4 Turn off power to your heating and cooling system

Part 2: Remove Old Thermostat and Install New Thermostat .... Page 4

2.1 Expose wires connected to old thermostat

2.2 Label and disconnect the wires

2.3 Install new thermostat’s wallplate

2.4 Match and connect wires

2.5 Set switch

2.6 Install batteries

2.7 Snap thermostat to the wallplate

Part 3: Quick Setup..................................................................... Page 13

3.1 Get to know your thermostat

3.2 Select options

3.3 Set fan and system switch

3.4 Turn on power to your heating and cooling system

Part 4: Additional Thermostat Features.................................... Page 17

4.1 Set change ﬁlter reminder

4.2 Change batteries

4.3 Adjust actual temperature display

Part 5: Troubleshooting Guide.................................................... Page 19

TABLE OF CONTENTS

• Failure to read and follow all instructions carefully before installing

or operating this control could cause personal injury and/or

property damage.

• The thermostat may stop controlling temperature and your house

may freeze or overheat when batteries are too low. Batteries must

be changed when or appears on the

display.

2 3

Part 1 Before Getting Started

1.1 Check package contents

Open the package and verify that the following items are included:

• Thermostat Wallplate (A) and Cover (B)

• 2 mounting screws and wall anchors (C)

• Wire Labels

• Installation Instructions and User Guide

Before getting started, please review the following

pre-installation checklist.

If any of the items shown above are missing from your package,

call White-Rodgers™customer service at 1-877-654-9394 before

returning the thermostat to your place of purchase.

✔Do you have either oil or gas burning furnace?

✔Do you have Hydronic Heating (steam or hot water radiators or

radiant ﬂoor heating)?

You will need the following tools:

✔Flat-head screwdriver

✔2 AA alkaline batteries

You may also need:

✔Hammer

✔Drill with 3/16" (4 mm) bit

✔Small pliers to bend wires

Typically, this is achieved by ﬂipping a switch on the outside of the

furnace/air handler to the “OFF” position.

1.2 Answer questions about source of

heating in your home

1.3 Assemble tools

1.4 Turn off power to your heating and

cooling system

Do not turn the system back on until you have

completed the installation and set up of the thermostat.

4 5

AUX

Part 2 Remove Old Thermostat and

Install New Thermostat

Do not disconnect wires from the old thermostat until you

label all the wires according to this manual.

2.1.1After turning off power to your heating & cooling system,

expose wallplate with wires and wire terminals. The required

steps vary depending on your old thermostat type.

2.1 Expose wires connected to

old thermostat

✔The Cover: This usually pulls off, but is sometimes secured by a

screw which must be loosened.

✔The Base: This either pulls off or needs to be removed by loosening

screws under the cover.

✔The Wallplate: This is removed by loosening the screws that hold

the thermostat to the wall.

Your old thermostat may consist of:

• 3 parts: a cover, base and wallplate

• 2 parts: a cover and wallplate

Wallplate

Base

Cover

3-Part unit

2-Part unit

6 7

✔ Ignore wire colors. There is no standard color code for

thermostat wires.

✔ Ignore existing wire labels, if they are present.

✔ Use the provided labels to label/re-label the thermostat wires.

✔ The new labels must remain on the wires at least until the

installation process is complete.

✔ No two wires can have the same label.

2.2.1 Note you may see two types of wiring in the old thermostat:

1. Wires leading from the wall to a

terminal on the thermostat

2. Wires connecting one terminal to

another (jumper wire).

These don’t have to be labeled.

2.2 Label and disconnect the wires

wall

2.1.2 Loosen all screws holding the old thermostat’s wallplate to

the wall. Do not disconnect the wires from terminals. Allow

the wallplate to hang loosely on the wires.

Wall opening

Wallplate hanging on the wires

8 9

If the OLD thermostat’s

terminal is wired into the wall

and identiﬁed by this letter…

…Then label its wire with

this letter:

You’ll need this information further in the installation process!

2.2.2 Label each wire that comes out of the wall and attaches to

terminals on the old thermostat. Use labels provided with your

new thermostat.

1. Note the letter printed near each wired terminal

2. For each out-of-the-wall wire:

– ﬁnd its terminal letter(s) in the left column of the table

on page 9,

– label the wire according to the right column of the table.

3. Make the following notes in the right column of the table

on page 9:

– Circle all your out-of-the-wall

labeled wires

– Pencil in any jumper wire

connecting 2 terminals

Mislabeling the wires could result in damage to your

heating and cooling unit.

Contact White-Rodgers™Customer Service at 1-877-654-9394 if your

old thermostat contains any wired terminals not listed in the table.

Note: No thermostat installation uses all of the wires shown

on page 9. In most cases, between 4 and 5 terminals are wired.

wall

RC, R

RH, 5, R5

W, 4, W1

Y, Y1

X, C

wall

If terminal “O” is NOT wired.

If terminal “O” is wired.

2.2 Label and disconnect the wires (cont.)

Examples

2.2.3 After labeling all the wires, use a screwdriver to disconnect

each wire from its terminal. Remove the old thermostat.

Make sure that the wires don’t fall

into the wall after you detach them from

the old thermostat. You may choose to

tape them to the wall or tightly wind them

around a pencil or screwdriver.

10 11

2.4 Match and connect wires

2.4.1 Match each wire coming from the wall to its corresponding

terminal, as shown in the illustration below. Insert each wire into

the hole on the side of its matching terminal. Using a screwdriver,

tighten the screw securely. DO NOT REMOVE THE WIRE LABELS.

A maximum of one wire from the wall can be wired

into each terminal.

No thermostat installation uses all of the wires shown below.

In most cases, between 4 and 5 terminals are wired. The remaining

terminals will not be used.

2.4.2 In the new thermostat, a jumper wire

connects the RC and RH terminals.

If, in your OLD thermostat… Then…

Terminals RC and RH (or 5, or R5) …leave the jumper wire in place

were connected by a jumper wire, in the new thermostat.

There was a terminal R, which you then …leave the jumper wire in place

labeled RC according to 2.2.2, in the new thermostat.

Terminals RC and RH (or 5 or R5) …remove the jumper wire from the

were NOT connected by a jumper wire, new thermostat.

If you’re not sure whether terminals RC and RH were connected in your old

thermostat, refer to your notes made in section 2.2.2.

GAS

ELEC

CGOY

WRHBRC

2.3.1 Detach the new thermostat’s wallplate from the rest of the

thermostat and position the wallplate on the wall according to

the illustration below, passing the labeled wires through the

wire hole in the center of the wallplate.

2.3.2 With the wallplate ﬂush against the wall, mark mounting holes

with a pencil.

2.3 Install new thermostat’s wallplate

Do not allow wires to touch each other or parts on

the thermostat. Doing so could result in damage to your heating and

cooling unit.

2.3.3 Move the wallplate aside. Drill the mounting holes using a 3/16"

drill bit. With a hammer, tap the wall anchors, provided in the

package, into the drilled holes.

2.3.4 Position the wallplate on the wall again and screw the mounting

screws into the wall anchors. Do not use a power screwdriver,

you may damage your thermostat.

Wallplate

Mounting hole

CGOY

RH RH

RC RC

12 13

System Switch

Cool - air conditioning

Heat - heating

Off - system turned off

Fan Switch

On - fan always on for air circulation

Auto - fan runs only when system

provides Heating or Cooling

Indicates system

currently providing

Heating (ﬂame

icon) or Cooling

(snowﬂake icon)

Find a switch located in the lower right corner of the wallplate labeled

ELEC/GAS. Set it as follows:

2.5 Set switch

• If you have either a gas or oil furnace, set the switch to GAS.

• If you do NOT have a gas or oil furnace, set the switch to ELEC.

Install 2 AA alkaline batteries (not included) into the battery

compartment at the top of the thermostat.

2.7 Snap thermostat to the wallplate

2.6 Install batteries

Do not restore power to the heating and cooling system

until instructed.

Part 3 Quick Setup

3.1 Get to know your thermostat

Actual

Temperature

Desired

Temperature

Temp Up/Down

Buttons

GAS

ELEC

CGOY

WRHBRC

GAS

ELEC

14 15

Set SYSTEM switch to OFF position and then press both buttons

simultaneously.

You will be prompted to answer 5 “Options” questions, on page 15.

As each option is presented:

✔Use the

buttons to answer each question.

✔Then press both buttons simultaneously

to move to the next question.

When you have answered all 5 questions, set SYSTEM switch to

HEAT position.

Options Default Setting Additional Information

1. Do you want the FA Select SL (slow) if you have

Cycle Rate to be (fast) Hydronic (water or steam)

Fast or Slow? heating. Otherwise, select

default FA.

2. Do you want 000 Select default 000 for now.

to be reminded (no reminder) To set a ﬁlter-change

when it is time reminder, see section 4.1

to change the

air ﬁlter? (FILTER)

3. Compressor OFF Select ON to provide

Lockout (LOC) protection to your Heating

and Cooling System’s

compressor

4. How much 0HI (no offset) Select default 0HI for now.

displayed To adjust the actual

temperature offset temperature reading, see

do you want? section 4.3

5. Do you want °F

temperature (Fahrenheit)

displayed in °C

(Celsius) or °F

(Fahrenheit)?

3.2 Select options

16 17

3.4 Turn on power to your heating and

cooling system

Congratulations!

You have completed the basic setup of

your new thermostat. It’s ready to use.

To read about additional thermostat features, continue to section 4.

1. Set the FAN switch to AUTO.

2. Set the SYSTEM switch to COOL (to turn on cooling) or HEAT (to

turn on heating).

3.3 Set fan and system switches Part 4

Additional thermostat features

The thermostat can display a reminder when it is time to change the air

ﬁlter on your heating and cooling system.

To enable Change Filter reminder:

1. Set SYSTEM switch to OFF position.

2. Press both the buttons simultaneously two (2) times until you

see FILTER icon in the lower left corner of the display.

3. Using the buttons select the number of hours until you would like

to be reminded of the ﬁlter change. The hours increase in

increments of 50.

4. Move SYSTEM switch back to COOL or HEAT position when you

are ﬁnished.

5. Once the set time has elapsed, FILTER will be displayed on

the screen.

6. Reset the reminder by pressing both

the

buttons simultaneously

when the FILTER is displayed.

When the thermostat displays

you need to replace batteries with 2 new AA alkaline batteries.

4.1 Set change ﬁlter reminder

4.2 Change batteries

Inhaltsverzeichnis

Andere White Rodgers Thermostat Handbücher

White Rodgers

White Rodgers 1F95W-80 Bedienungsanleitung

White Rodgers

White Rodgers 1F95W-71 Bedienungsanleitung

White Rodgers

White Rodgers SuperStat Pro SuperStat Pro Programmable... Bedienungsanleitung

White Rodgers

White Rodgers 1F95-1280 Bedienungsanleitung

White Rodgers

White Rodgers 1F73 Bedienungsanleitung

White Rodgers

White Rodgers 1F82-0261 Bedienungsanleitung

White Rodgers

White Rodgers 1E78-140 Bedienungsanleitung

White Rodgers

White Rodgers 1F60-22 Montageanleitung

White Rodgers

White Rodgers BNP125 Verdrahtungsschema

White Rodgers

White Rodgers 1F83-51 Bedienungsanleitung

White Rodgers

White Rodgers 1F80-261 Bedienungsanleitung

White Rodgers

White Rodgers 1F92W-71 Bedienungsanleitung

White Rodgers

White Rodgers 1F85-277 Bedienungsanleitung

White Rodgers

White Rodgers 1F80-0471 Bedienungsanleitung

White Rodgers

White Rodgers 1F80-224 Bedienungsanleitung

White Rodgers

White Rodgers 1F89-211 Bedienungsanleitung

White Rodgers

White Rodgers 1F87-0261 Bedienungsanleitung

White Rodgers

White Rodgers 1F72 Bedienungsanleitung

White Rodgers

White Rodgers 90 SERIES Bedienungsanleitung

White Rodgers

White Rodgers WHITE RODGERS 1E50N-303 Bedienungsanleitung

White Rodgers

White Rodgers 1F89EZ-0251 Montageanleitung

White Rodgers

White Rodgers 1F95CA-391 Bedienungsanleitung

White Rodgers

White Rodgers 1F95W-80 Bedienungsanleitung

White Rodgers

White Rodgers IF73 Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Honeywell

Honeywell T6811 Bedienungsanleitung