WilTec CET-80000 Installationshandbuch

http://www.WilTec.de

http://www.aoyue.eu

http://www.teichtip.de

Operation Manual

50982- CET-80000

Read and follow the operating instructions and safety information before using for the first time.

Technical changes reserved!

Due to further developments, illustrations, functioning steps and technical data can differ insignificant-

ly.

Updating the documentation

If you have suggestions for improvement or have found any irregularities please contact us.

http://www.WilTec.de

http://www.aoyue.eu

http://www.teichtip.de

The information contained in this document is subject to change without prior notice. No part of this

document can be copied or duplicated in another form without the prior written consent of WilTec Wil-

danger Technik GmbH. The WilTec Wildanger Technik GmbH assumes no liability for any errors in

this user manual or the connection diagram.

Although WilTec Wildanger Technik GmbH has made every effort to make sure that this user manual

is complete, accurate and updated, errors cannot always be avoided. In the event of problems with

this user manual please complete and send this form back to us.

FAX-notification (+++49 2403 55592-15),

from: ________________________________________

Name: ________________

Firm:_____________________

Tel/Fax:__________________

I would like to report the following mistakes:

___________________________________________________________________

Customer Service WilTec Wildanger Technik GmbH

e-mail: service@WilTec.info

Tel:++ +49 2403 55592-0

Introduction

Thank you for purchasing this quality product. To minimize the risk of injury by means of fire or

electric shock we urge that our clients take some basic safety precautions when using this

device. Please read the operation instructions carefully and make sure you have understood its

content.

Always use a grounded power connection with the appropriate mains voltage. You can find the corre-

sponding mains voltage on the type plate. If you have any doubts about the connection being ground-

ed, have it checked by a qualified professional. Never use a faulty electric cable.

Do not inspect the electrical part of the pressure pond filter in a wet or damp environment or when you

are wet yourself and protect it from direct sunlight. Install this device in a safe location so that nobody

can step on the cable, fall over or damage it. Disconnect the power plug before cleaning it and use

only a damp cloth for cleaning. Avoid using cleaning agents and make sure that no liquid enters the

electrical part of the pump.

The electric part of the device contains no parts that can be inspected or serviced by the user. Leave

the maintenance, adjustment and repair to qualified technical personnel. In case of unauthorised inter-

vention the 2-year warranty is no longer valid! Keep these operation instructions safe.

http://www.WilTec.de

http://www.aoyue.eu

http://www.teichtip.de

UN PACKING

Notify your dealer immediately if there are external damage.

SAFETY INSTRUCTIONS

1> For your own safety, please contact an electrical specialist in case of questions

and problems.

2> Do not connect the power supply when the all parts are not installed.

3> Plug in the pump only to a power receptacle with ground contact. This type of out-

let must have been set up according to the respective national directives (VDE.

EN……IEC etc.) Insure that the PE conductor extend all the way to the pump.

4> Make sure the voltage in the pump is the same with the actual power supply.

5> Electrical installations on garden ponds must correspond to the international and

national installation directives.

6> Only operate the pump if no one is in the water.

7> Do not carry or pull the pump by the connecting cord.avoid the cable over heat,

greasy or touch acute angle.

8> The pump may not be operated if the cable or the casing are defective.

9> Never displace any liquids other than water.

10> Attention: the pump will automatically stop working if overload or run without wa-

ter.

11> The controller is not water-proof design, so put it in a dry and ventilated place.

USING APPLICATIONS

Apply to ponds, rockery, bourne, aquarium tanks and seafood tanks.

FEATURE

1> Multi-function intelligent control, can adjust flow and power.

2> The new electronic frequency conversion technology, energy saving 60%

3> Centrifugal impeller design, improve the H-max and output.

4> Super silence, cab be used both in fresh and sea water.

5> Novel design and generous, rotary handle, easy to carry.

6> Rotary footings, can work both vertical or horizontal.

7> Ceramic shaft, wear resistance, no rust.

8> Long service life, no copper element

9> The outlet realize multistage over, suitable for a variety of pipe diameter connec-

tion.

10> Separation of electric drive, more safe and stable.

11> The external aluminum alloy radiator of the controller can dispatch heat well .

12> With anti-blocking and anti-idling function ( immediately cut off power automati-

cally if impeller blocked, immediately cut off power automatically if pump run idling)

http://www.WilTec.de

http://www.aoyue.eu

http://www.teichtip.de

13> With abnormal alarm function. This pump can warn you of various abnormal

problems in time.

INSTALLATION

1> Notify your dealer immediately if there are external damages.

2> Compare the Voltage and frequency of your electrical circuit with the data on the

model plate, these data must agree.

3> Connect the pipeline if needed. (Attention: the piping system shall not have bub-

ble.) Hose connection diagram is as follows.

This product have variety of outlets, you can select according to the size. Loosen the

nut in clockwise direction, connect the hose, Tighten the nut in anti-clockwise direc-

tion.

4> Attention: the pump must installed below the water level 20cm at least, the sur-

face must firm and horizontal.

5> Do not place the pump directly in the ponds floor that have mud, place it on a

raised surface.

6> Connect the pump with the controller of four core wire (PIC 1), lock the nut as

shown in PIC 2

http://www.WilTec.de

http://www.aoyue.eu

http://www.teichtip.de

CONTROLLER USE

The controller is consist of hook, panel, touch button, fixed foot.

1> Switch function

After the power is switched on, touch “START-STOP”, control the switch of pump.

Attention: please cut off the power if long time no use.

2> Adjust the gear.

Touch “DOWM” or “UP” to adjust pump gear. Consult the detailed performance data

as below.

Model Voltage Gear Power

(W) Output

(L/h) H-max

(m) Flow rate

(1.5m)

50982

(CET-

8000)

110V~22V

50~60HZ

SP01 18 3500 1.6 500L

SP02 23 4000 1.9 1350L

SP03 28 4600 2.3 2000L

SP04 35 5000 2.7 2600L

SP05 42 5400 0.1 3200L

SP06 51 5800 3.5 3500L

SP07 60 6200 3.9 3800L

SP08 66 6700 4.5 4500L

SP09 73 7200 4.8 4800L

SP10 80 8000 5.4 5100L

http://www.WilTec.de

http://www.aoyue.eu

http://www.teichtip.de

3> Feeding function

Long press “UP” until the buzzer sound twice, you now in the state of delay start. You

have 10 minutes to feed the fish. Operation is the same if you want cancel this delay

start..

4> Lock / Unlock function

After you get the correct gear you want, you need press ”down” until the buzzer

sounds twice. You now in the state of locked. the unlock function is the same opera-

tion.

5> Automatic memory function

When the controller power off suddenly, it still have memory. The pump will automatic

recovery to a working state as before when power on.

6> Alarm function

The pump will immediately cut off power automatically if pump run idling. Then re-

start automatically to work again after 5 seconds. If still run idling the pump will auto-

matically power off again. After repeated five times the pump will power off until re-

connect the power. Meanwhile, the buzzer will sounds short time to make alarm.

The pump will immediately cut off power automatically if impeller blocked, and the

buzzer will sounds to make alarm until re-connect the power.

7> Code definition and troubleshooting.

Code

Definition Status Troubleshooting

P000 Power Normal /

SP00 Gear Normal /

FEE0

Delay start Normal /

ER05

Short-circuit current display Abnormal

check the controller

ER04

overheat flicker Abnormal

clean the pump

ER03

pump work without water Abnormal

check the pump if working without wa-

ter

ER02

pump block Abnormal

check the impeller if block

ER01

over/under voltage display Abnormal

check voltage

http://www.WilTec.de

http://www.aoyue.eu

http://www.teichtip.de

MAINTENANCE / CLEANING

Please clean the filter casing, impeller, rotor and shaft part regularly. Please cut off

the power when clean it:

①Turn and take off the filter casing as Pic 1 and Pic 2.

②Press the insurance clasp vertically as Pic 3, and take off the impeller cover as Pic

③take off the rotor set as Pic 5, then you can clean or change.

④The installation position of the O-ring as Pic 6

If the pump is not used for a long time, please full out the pump, it is better to run the

pump in the clean water for a short time. And then rinse with clean water. Clean and

make sure the pump is dry, put it in a stable place.

If the temperature is below 0 degree, the water in the pump should be discharged

immediately. In order to prevent freezing damage of water pump.

TROUBLESHOOTING

Problem

Cause

Troubleshooting

pump do not run

No power supply Connect the power

Burning machine Change pump

Impeller stall Clean and re-link to power

Run without water Fill with water and re-link to power

Not connected with the controller

Re-link the controller

The controller is damaged Change the controller

Pump noise Dirty inside Clean pump

shaft break or wear change shaft

Pump water

shortage

Damage of the impeller change impeller

inlet and outlet obstruction clean the inlet and outlet

filter case obstruction clean filter case

low voltage adjust voltage

http://www.WilTec.de

http://www.aoyue.eu

http://www.teichtip.de

DRAWING

NO. NAME NO. NAME

1 Bottom foot 8 ceramic bearing

2 filter case 9 motor with cable

3 outlet 10 rear cover

4 seal circle 11 handle

5 impeller cover 12 rubber foot

6 rotor set 13 Gear box with cable

7 O-Ring

http://www.WilTec.de

http://www.aoyue.eu

http://www.teichtip.de

Disposal regulations

EU guidelines regarding the disposal of scrap electric appliances (WEEE, 2002/96/EC) were imple-

mented in the law related to electrical and electronic equipment and appliances.

All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out

wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the

domestic waste.

The company WilTec Technik GmbH has been registrated in the German registry EAR under the

WEEE-registration number DE45283704.

Disposal of used electrical and electronic appliances

(intended for use in the countries of the European

Union and other European countries with a separate

collection system for these appliances).

The logo on the article or on its packaging points out

that this article must not be treated as normal house-

hold waste but must be disposed to a recycling collec-

tion point for electronic and electrical waste equip-

ment. By contributing to the correct disposal of this

article you protect the environment and the health of

your fellow men. Environment and health are threat-

ened by inappropriate disposal.

Materials’ recycling helps reduce the consumption of raw materials.

Additional information on recycling this article can be provided by your local community, municipal

waste disposal facilities or the store where you purchased the article.

Address:

WilTec Wildanger Technik GmbH

Königsbenden 12 / 28

D-52249 Eschweiler

Important notice:

The reprint or reproduction, even of excerpts, and any commercial use, even in part of this instructions

manual require the written permission of WilTec Wildanger Technik GmbH.

Inhaltsverzeichnis

Andere WilTec Wasserpumpe Handbücher

WilTec

WilTec CTF-2800 Bedienungsanleitung

WilTec

WilTec 50723 Anleitung zur Verwendung

WilTec

WilTec 51545 Bedienungsanleitung

WilTec

WilTec 50741 Bedienungsanleitung

WilTec

WilTec 50588 Bedienungsanleitung

WilTec

WilTec 61963 Bedienungsanleitung

WilTec

WilTec 51530 Bedienungsanleitung

WilTec

WilTec 50752 Bedienungsanleitung

WilTec

WilTec 92491 Bedienungsanleitung

WilTec

WilTec 61541 Bedienungsanleitung

WilTec

WilTec 62935 Bedienungsanleitung

WilTec

WilTec 50588 Bedienungsanleitung

WilTec

WilTec 51537 Bedienungsanleitung

WilTec

WilTec Urea/AdBlue 51353 Bedienungsanleitung

WilTec

WilTec 50233 Bedienungsanleitung

WilTec

WilTec 61169 Bedienungsanleitung

WilTec

WilTec 51552 Bedienungsanleitung

WilTec

WilTec TeichTip Sunsun CMP-28000 Bedienungsanleitung

WilTec

WilTec 50741 Bedienungsanleitung

WilTec

WilTec 50743 Bedienungsanleitung

WilTec

WilTec XPOtool 63444 Bedienungsanleitung

WilTec

WilTec 51552 Bedienungsanleitung

WilTec

WilTec EGP Bedienungsanleitung

WilTec

WilTec 62138 Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung