Winsport Karella E-MASTER Bedienungsanleitung

Instruction manual

Before use, please read the operating instructions carefully and keep it!

Karella

E-MASTER

Stand: 16. Mai 2019

Operating manual

8111.01 REV_DA_16052019

CONGRATULATIONS FOR THE PURCHASE OF YOUR KARELLA DART MACHINE.

Before you mount device and use it, please read the following instructions first and keep it.

Only so you can use the device safe and with high reliability.

Familiarize yourselves in particular with the safety regulations.

IMPORTANT: The assembly may only be done by adults.

Use this device exclusively for the supposed purpose.

Technical advice:

If the power cord is connected to a socket, the unit is automatically powered. To operate the appliance,

please switch the main switch of the appliance to 'ON'.

Mains voltage: 110 - 240VAC / 50 Hz

Max. Power Consumption: 120 WMAX

Within the device there are no voltage potential which could endanger life, all of the circuits use a

voltage potential of 5 Volts or 12 Volts.

Dimension wall unit

Height: 97,5cm

Width: 62,0 cm

Depth: 46,5cm

Weight: approx. 45,0 kg

Dimensions base-underframe (optional)

Height: 210,0 cm

Width: 60,0 cm

Depth: 60,0 cm

Weight: approx. 8,0 kg

CAUTION: Electric shock due to cable damage –If you notice any visible damage to your E-

Master or power cord, do not use it.

Do not touch the cable until the plug has been disconnected from the socket.

Replace damaged cable completely.

It is forbidden to mend the defective cable with insulating tape. Repairs are only allowed by qualified

personnel.

Always route cables without tripping hazards and always choose extension cables long enough.

Cable must always be placed splash-proofed.

Never touch the mains plug and socket with wet hands. Only connect the device to AC power. The

specified voltage on the identification plate must match the voltage of the power source.

ATTENTION: PLEASE READ CAREFULLY PRIOR TO COMMENCING THE ASSEMBLY AND

USE OF THE UNIT.

It is not a toy! Danger for children –Choking hazard. Small parts.

With not appropriate use for article of every kind all guarantee claims go out!

Operating manual

8111.01 REV_DA_16052019

Please observe the following safety instructions to ensure a long life and optimal function of your

dartmachine:

(1) Do not try to open the unit by force. It contains no parts or components to which the user will be able to

repair. Consult a specially trained professional if there is a need for a repair.

(2) Slots and other openings on the top, sides, and bottom of the cabinet supports the ventilation system.

To ensure the unit is working properly and does not overheat, these openings must not be blocked or

covered.

(3) No sharp objects should be pushed through slots in the interior of the apparatus, as they could touch

live parts. It could cause a short circuit followed by a fire.

(4) The appliance must not be installed or located close to the heat source.

(5) No liquid may be poured over the apparatus. If this happens anyway, the device must be checked by a

specialist.

(6) Never expose the unit to rain or high humidity.

7) If you pass on the dartboard to another person, make sure that this person knows the contents of the

set-up and operating instructions.

(8) Before each use, you should check all parts for their function and should not use this device in the

case of faults occurring

CAUTION: Always unplug the power cord before cleaning the device.

CAUTION: Missing or modified safety devices.

Safety devices are for your protection. Never change or bypass safety devices.

ACCESSORIES & SPARE PARTS

Only use original accessories and original spare parts, they guarantee the safe and trouble-free operation of the

device. Information about accessories and spare parts can be obtained from your dealer.Li

DELIVERY

During unpacking, check the contents of the device for completeness. If there are no accessories included or

transport damages, please inform your dealer.

Winsport accepts no liability for damage that should be caused by disregarding these instructions.

We reserve the right to technical innovations or deviations in color and design.

Please keep the original packaging for possible later returns.

Operating manual

8111.01 REV_DA_16052019

Content

1. ASSEMBLY INSTRUCTIONS......................................................................................5

1.1. Wallmounting........................................................................................................................5

1.1. Mounting with stand (optional) ..............................................................................................6

1.2. Put up the start-line ad adjusting the height..........................................................................7

2. DETAILS AND STARTING UP....................................................................................8

2.1. Detail view of the device........................................................................................................8

2.2. Disassembly and maintenance of the dartboard...................................................................9

2.3. Start up.................................................................................................................................10

2.4. Delete credits.......................................................................................................................10

2.5. Keys...............................................................................Fehler! Textmarke nicht definiert.

2.6. Display .................................................................................................................................11

2.7. Coin validator.......................................................................................................................11

2.8. Overview..............................................................................................................................12

2.9. Testmenu.............................................................................................................................12

2.10. Sound...................................................................................................................................15

2.11. Main bookkeeping................................................................................................................15

2.12. Secundary bookkeeping......................................................................................................15

2.13. Turniermodus.......................................................................................................................16

2.14. Werkseinstellungen / Reset.................................................................................................16

2.15. Setup Menu..........................................................................................................................17

2.16. Sound Volume adjust...........................................................................................................21

3. GAME RULES...........................................................................................................22

Attention: The manual is intellectual property of Winsport e.K. Reproduction of the entire manual or individual

passages is only permitted with the written permission of Winsport.

Operating manual

8111.01 REV_DA_16052019

1. Assembly Instructions

Please read the instructions carefully before you start assembling! Always mount the dartboard with at least two

adults!

1.1. Wallmounting

Step 1

Open the device and remove the accessory set.

Loosen the safety screw and remove the Wall bracket from

the back of the device.

Step 2

Attach the wall bracket with the supplied our dowels (Ф 8 mm)

and screws (6 x 50 mm) on the wall. The position of the drill

holes can be found in the sketch beside.

Step 3

ATTENTION: Please carry out this procedure with

two peoples –never alone!

Hang the device in the wall bracket and fix the device with the

safety screw on the wall bracket.

Stept 4

After the device has been properly installed, the device can be

connected to the power supply.

ATTENTION: The power cable must not cause tripping hazards.

Always use appropriate cable extensions, if the distance to the socket

should be too big!

Note: 2 people needed to

mount the device.

Operating manual

8111.01 REV_DA_16052019

1.1. Mounting with stand (optional)

ATTENTION: For safety reasons, it is absolutely necessary to secure the unit against

falling over by attaching it to the floor or wall.

Step 1

Open the device and remove the accessory set.

Loosen the safety screw and remove the Wall bracket from

the back of the device.

Step 2

Take the two lower parts # 1 and connect them to the cross brace # 2. Use the supplied screws and nuts for this.

Step 3

Now insert the upper part # 3 on the two cross-beams and screw them together with the screws and nuts

provided.

ATTENTION: Before you hang up the device to the stand-foot,

make sure that the device stands on his final place.

Step 4

ATTENTION: Please carry out this procedure with two people

–never allone!

Hang the device in the holder of the stand and secure the device to the pedestal-bracket with the safety screw.

To ensure a secure footing, place the device on a firm and level floor, so that the device is in the balance.

Step 5

After the device has been properly installed, the device can be connected

to the power supply.

ATTENTION: The power cable must not cause tripping hazards.

Always use appropriate cable extensions, if the distance to the socket

should be too big!

Note: 2 people neede to

mount the device.

Operating manual

8111.01 REV_DA_16052019

1.2. Put up the start-line ad adjusting the height

High of the Bull’s Eye: The distance from the Bull's Eye to the ground should be 1.73m.

The distances are additionally marked in the

enclosed measure-tape, so that a correct

installation is facilitated.

Start-line: The distance between the throw-off line

and Bull's Eye (not the wall!) should be 2.37m on

the ground or 2.93m diagonal from the startline.

Bull´s Eye

Start-line

Operating manual

8111.01 REV_DA_16052019

Details and Starting up

2.1. Detail view of the device

The illustration below shows the inside of the dart machine. The maintenance of the device and the cleaning or

replacement of the dartboard are very simple and can be done by yourself.

Wooden support for the dartboard

Winged nuts holding the dartboard

Matrix field connector

Slot unit

CPU board

Speaker

LED Light

Counters

Supply

Infra sensor

Missed arrows Sensor

Operating manual

8111.01 REV_DA_16052019

2.2. Disassembly and maintenance of the dartboard

After a few thousand games broken arrow points could fill in or clog dartboard segments, resulting the arrows not

being able to stick on the dartboard. Then it is time to clean the dartboard. The broken tips can be removed with

the help of pliers, whereby those who cannot be pulled out with the pliers can push into the interior of the

segment. Then the dartboard has to be disassembled to be able to remove the pressed-in tips.

WARNING: Careless and incautious handling of the dartboard and its parts can cause damage and

provoke damage to the dartboard or its parts. To safely disassemble the dartboard follow the exact

sequence of the steps below.

Step by step disassembling the dartboard:

1. Turn off the device, open upper door and disconnect the sensor field connector on

the electronics board (see detail view 2.1.);

2. Unwind 4 wing nuts (see detail view 2.1.) and take out the dartboard to the front from its base;

3. Unwind 4 wing nuts from the rear side of the dartboard and remove the wooden base;

4. Carefully unwind the two screws from the sensor field and remove the sensor field and protective rubber;

5. Remove the broken tips and assemble the dartboard board to the opposite side;

6. After every disassembly and assembly it is important to check the sensor field function (test target, see chapter

5.1.1.).

Wood

Sensor

field

Rubber

Segments

Spider

Screws

Wood

Null sector

Operating manual

8111.01 REV_DA_16052019

2.3. Start up

When switched on, a start melody sounds. Before the device jumps into the demo mode, the device checks

whether there are clamping buttons. If a jammed key is found, "KEY BLK" will appear in the display and a warning

tone will sound

The device has a RAM memory where the last game is saved. Should be e.g. due to a power failure, the device

will be switched off during operation (for example, power failure), the last game can be continued after restarting

the device. Any existing credits are also saved.

If you throw on the dartboard without a valid credit, an alarm will sound - unless the device is in tournament mode.

2.4. Delete credits

To clear the credits, open the unit with the key, set DIP microswitch 5 (detailed explanation of the DIP

microswitches in Chapter 3) to ON, and press the player change button for a few seconds. Then set the

microswitch back to OFF.

2.5. Buttons

For those buttons that have multiple functions, pressing the keys changes the game (for example, you have to

press the key 3 times for game 501). In addition, the name of the game appears on the display. After selecting a

game, the option keys flash. These can be selected until the game starts, even if the lights on the keys stop

flashing. The selected option of the game will appear on the display.

180,301

501,701

901 Parcheesi Double In

Cut Throat

Cricket Double

Out Master

Out Team

Abort game

Button change player

Inhaltsverzeichnis

Andere Winsport Zubehör Handbücher

Winsport

Winsport GHIBLI Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung