Wittkopp Anchor 2600 Benutzerhandbuch
Anchor 2600
Installer manual
Installation and commissioning instructions
02 en_A2600-Teil 2b-Errichterhandbuch V2.03.docx
1 / 7
Note:
On the cover sheet you can find warning information, and an explanation of the symbols and
terms used, together with the exclusion of liability.
Contents
General................................................................................................................................. 2
Preparation for installation..................................................................................................... 3
Installation dimensions A2600........................................................................................... 3
Preparation of the boltwork / door...................................................................................... 3
Installation............................................................................................................................. 4
Wiring / installation................................................................................................................ 4
Connection of an analog keypad ....................................................................................... 5
Connection P- signal plus / UART ..................................................................................... 5
Function test.......................................................................................................................... 6
Input of the opening code.................................................................................................. 6
Keypad test ....................................................................................................................... 6
System setup ........................................................................................................................ 7
Mount the keypad before installing the electronic lock. All the keypads of the Primor series
with direct drive can be used (RO, RE). The function is generally given with all input units
of the Primor series, an additional handle for the drive of the bolt is needed, depending on
which keyboard was chosen. Details on installing the keypads are given in the installation
instructions (see sections “en_02 en_APxxx-Teil 2a-Errichterhandbuch Tastatur V2.05”).
Anchor 2600
Installer manual
Installation and commissioning instructions
02 en_A2600-Teil 2b-Errichterhandbuch V2.03.docx
2 / 7
General
Locks of the Anchor 4000 series have
standard installation dimensions and can
be mounted in all 4 installation positions
(right, left, top, bottom). They have been
designed for a boltwork with two blocking
edges, i.e. for the force to be applied only
on only the flank of the bolt.
They are intended to be installed in safes
made of metal.
Depending on the design, additional
blocking elements (e.g. bolt rails) can
optionally be attached to the lock bolt
using existing holes. A perfect function of
the lock and its connection must be
ensured.
The electronic lock requires no
maintenance in a normal residential or
office environment. We recommend a
security and function test of the electronic
lock after around 10,000 closings.
The breakthrough for the axis must not
exceed 11.4mm.
The lock must be protected against
attacks from outside. It is recommended to
protect the security-relevant parts of the
high-security lock against access even
when the door of the safe is open.
Do not apply any lubricants or other
substances to the lock.
Always use the following sequence for installation:
•Check the preconditions for installation
•Wiring / installation of the cables
•Set up the power supply
•Function test of the locking mechanism
•Make all the settings (user system, Dualcode, inputs and outputs, delay time)
Ensure that the load limits are not exceeded at any time.
You can find the corresponding values in Annex C "Technical data".
Anchor 2600
Installer manual
Installation and commissioning instructions
02 en_A2600-Teil 2b-Errichterhandbuch V2.03.docx
3 / 7
Preparation for installation
Installation dimensions A2600
Preparation of the boltwork / door
For mounting the lock there must be three
threaded holes for attachment to the
boltwork or within the safe door. The
electronic lock is to be attached with the
supplied M6 or 1/4" screws or cylinder
screws (minimum strength class 8.8).
The length of the screws must be 25 mm or
more so that a minimum screw-in depth of
5 mm is attained.
Anchor 2600
Installer manual
Installation and commissioning instructions
02 en_A2600-Teil 2b-Errichterhandbuch V2.03.docx
4 / 7
Installation
The fastening screws must be tightened so
that a permanent and firm hold is
guaranteed.
Tighten up the fastening screws to a
maximum torque of 3,5 –5 Nm. We
recommend the use of a bolt locking agent
(adhesive) to prevent the screws from
coming undone by themselves.
The bolt of the lock may not be under
tension or pressure after installation.
Pay attention to enough free space to the
blocking point.
Wiring / installation
If the lock is operated outside the area of
validity of the VdS, then signal boxes,
external power supplies, etc. can be used
with the Anchor in addition to all the analog
keypads that are compatible with the
Primor series.
The VdS approval is restricted to operation
with input units of the Primor FS, FL, RO,
RE and Anchor LC series.
If the wiring is not guided by the drive axis,
the required hole / way of wiring must be
selected in such a way that this gives no
access to the lock body through tools,
probes or similar.
Drilling for the wiring must be at least 8mm,
a maximum of 11.4mm.
For all work / changes to the wiring between the lock, keypad or signal boxes, the power
supply including the battery must be disconnected!
Anchor 2600
Installer manual
Installation and commissioning instructions
02 en_A2600-Teil 2b-Errichterhandbuch V2.03.docx
5 / 7
Connection of an analog keypad
As supplied, onlythe interface for an analog
keypad from the Primor series is active. If
the lock is to communicate with a digital
input unit, i.e., an "intelligent" one, then
additional settings are required in the setup
menu [6] in addition to the selection of the
corresponding interface or socket.
You can find the corresponding commands
in the user manual.
You can find information on inserting the
battery in the operating manual of the
corresponding Primor keypad.
.
Connection P- signal plus / UART
Connection via the second port (see above)
is always done if
•the lock system has an external
power supply,
•a "silent alarm" contact for
evaluation by an alarm system has
been made available,
•a system block by an external
signal (dry contact) is to be used.
Additional hardware is required to do this.
The lock is compatible with all the available
components of the Primor series.
You can find informationon the wiring in the
instructions for the signal box. The VdS
approval is no longer valid when used in
conjunction with a signal box or if the serial
interface (UART) is not used correctly.
analog keypad
e.g. Primor RO
serial interface [UART] or
[IO] for Alarmbox
If a signal block with "active release" (switching logic) has been set up this ensures that the
blocking is not switched off if the control cable iscut through. At the same, a cable breakage
within the safe always thus entails the risk of a blockade.
Anchor 2600
Installer manual
Installation and commissioning instructions
02 en_A2600-Teil 2b-Errichterhandbuch V2.03.docx
6 / 7
Function test
Carry out a function test after completing all
the mounting and installation work.With the
door open, you should open and close the
lock several times using the master code
that had been set at the factory.
The opening takes place after the release
by turning the keyboard (RO) or the
operating lever (RE):
Using the handle for the boltwork the safe
should be openedeasilyand reliablyclosed
again.
The locking check can be done via the
operating lever of the boltwork and should
be performed after each closing and
locking.
Input of the opening code
e.g. factory code Master
=✓
→
The opening code can be input
directly as described above, without
selection. After a valid code is input
the lock releases the bolt
movement for around 3 seconds.
Open the container with the
valuables within this time after
inputting the code.
=
Keypad test
We recommend a final keypad test using function menu 5 to ensure that all the numeric keys
function properly.
☼Checking the menu system
Press the keys in the
sequence
…
=✓
Press each numeric key once.
A functional key is indicated by a
double signal tone.
A key that is not recognised is
indicated by a long signal tone and
the function test is terminated. The
system must be checked.
Anchor 2600
Installer manual
Installation and commissioning instructions
02 en_A2600-Teil 2b-Errichterhandbuch V2.03.docx
7 / 7
System setup
The setting options and the control sequences that are required are described in the user
manual.
We therefore recommend the following procedure:
•Setup of the users [menu 1]
•if applicable, parameterisation of the inputs and outputs [menu 6]
•if applicable, setting up the Dualcode condition [menu 6]
•if applicable, setting up the delay time [menu 9]
In particular, the user system can be made markedly faster by using setup mode [menu 8].
The repetitive input of the master code is then restricted to selecting setup mode.
Inhaltsverzeichnis
Andere Wittkopp Sperren Handbücher
Wittkopp
Wittkopp Primor 1000 Benutzerhandbuch
Wittkopp
Wittkopp Primor 1600 Benutzerhandbuch
Wittkopp
Wittkopp Insys 7202 Bedienungsanleitung
Wittkopp
Wittkopp Primor P30 Series Bedienungsanleitung
Wittkopp
Wittkopp Primor Level 5 Bedienungsanleitung
Wittkopp
Wittkopp Primor 3000 Bedienungsanleitung
Wittkopp
Wittkopp Anchor 4000 Series Bedienungsanleitung
Wittkopp
Wittkopp ANCHOR Bedienungsanleitung
Wittkopp
Wittkopp BlueCam greendot Bedienungsanleitung
Wittkopp
Wittkopp 7800 Bedienungsanleitung
Wittkopp
Wittkopp Primor Series Bedienungsanleitung
Wittkopp
Wittkopp Primor Series Bedienungsanleitung
Wittkopp
Wittkopp TwinLock 7220 Bedienungsanleitung
Wittkopp
Wittkopp Primor 100 Bedienungsanleitung
Wittkopp
Wittkopp GATOR F Bedienungsanleitung
Wittkopp
Wittkopp FinKey Bedienungsanleitung
Wittkopp
Wittkopp OPTIMA 2648 Bedienungsanleitung
Wittkopp
Wittkopp Primor 2600 Benutzerhandbuch
Wittkopp
Wittkopp Primor 2000 / Level 5 Bedienungsanleitung
Wittkopp
Wittkopp Anchor 7000 Bedienungsanleitung
