Wittkopp Anchor 7000 Bedienungsanleitung

Anchor 7000

Installation Manual

Installation and Commissioning Manual

02 A7000-Part 2b-Installation Manual V1.04

1 / 10

Note:

The cover sheet provides warning information, and an explanation of the symbols and terms

used, together with our disclaimer.

Contents

General................................................................................................................................. 2

Preparation for installation..................................................................................................... 3

Installation dimensions of lock A7000................................................................................ 3

Preparation of the boltwork / door...................................................................................... 4

Installation............................................................................................................................. 4

Cabling / installation.............................................................................................................. 4

Cabling.............................................................................................................................. 4

Connection of an analogue keypad ................................................................................... 6

UART connection .............................................................................................................. 6

Connection of alarm contacts ............................................................................................ 7

Connecting an alarm system outside the scope of the VdS ........................................... 7

Connecting an alarm system within the scope of the VdS.............................................. 9

Functional test......................................................................................................................10

Input of the opening code.................................................................................................10

Keypad test ......................................................................................................................10

Figure 1 - Dimensional drawing............................................................................................. 3

Figure 2 - Drilling positions for the Primor FS........................................................................ 5

Figure 3 - Cable connection .................................................................................................. 6

Figure 4 - Assignment of the alarm interface......................................................................... 8

Figure 5 - Connection of the Gator Signal plus...................................................................... 9

Mount the keypad before installing the electronic lock. For information on how to install the

keypads, please refer to “APxxxx Part 2a- Keypad Installation Manual”.

Anchor 7000

Installation Manual

Installation and Commissioning Manual

02 A7000-Part 2b-Installation Manual V1.04

2 / 10

General

A7000 series locks have standard

installation dimensions and can be installed

in all 4 installation positions (right, left, top,

bottom). They are designed for “scissor-

bolt” movements, i.e. for force absorption

by the bolt flanks.

They are intended to be installed in metal

safes.

Depending on the version, additional

locking elements (e.g. angle rail with bolts)

can optionally be attached to the bolt using

the existing holes. Ensure the proper

operation of the lock and its connection.

The electronic lock is maintenance-free in a

normal residential or office environment.

After approximately 10,000 closures, it is

recommended to have a security and

functional check of the electronic lock

conducted by a safe technician.

No not allow the opening for the keyhole to

exceed a rectangle measuring 27 x 9 mm.

It is essential that the lock is protected

against external attacks. We recommend

protecting the security-relevant

components of the high-security lock from

being accessed even when the safe door is

open.

Do not apply any lubricants or other

substances to the lock.

Multiple locks where the closure needs to

be checked by a bolt movement, as is the

case with the A-7000, may not be installed

on the boltwork of a safe. If the lock on a

boltwork is combined with locks featuring a

closing status indicator, then the A-7000

must first be closed and the closure status

checked.

Anchor 7000

Installation Manual

Installation and Commissioning Manual

02 A7000-Part 2b-Installation Manual V1.04

3 / 10

Always adhere to the following sequence for installation:

Preparation for installation

Installation dimensions of lock A7000

Figure 1 - Dimensional drawing

•Check the preconditions for installation

•Wiring / installation of the cables

•Disconnection of the power supply

•Functional test of the locking mechanism

•Perform all settings (user installation, time delay)

Anchor 7000

Installation Manual

Installation and Commissioning Manual

02 A7000-Part 2b-Installation Manual V1.04

4 / 10

Preparation of the boltwork / door

To install the lock, there needs to be three

threaded fixing holes on the boltwork or

inside the safe door. Use the screws

supplied or M6 of 1/4” cylinder screws (min.

strength class 8.8) to fix the electronic lock.

Measure the length of the screws to ensure

a minimum screw penetration depth of 5

mm.

Installation

Tighten the retaining screws to ensure a

permanent and firm hold.

Tighten the fastening screws with a

maximum torque of 3.5 - 5 Nm.

We recommend using a bolt locking agent

(adhesive) to prevent the screws from

coming undone by themselves.

Ensure that the bolt of the lock is not under

tension or pressure once installed.

Make sure there is sufficient clearance to

the locking point.

Cabling / installation

Cabling

Fundamentally, the installation positions of

the input unit and lock can be sited

independently of each other. Make

openings with a diameter of 9 mm through

which to pass the cables into the safe.

Particularly when using series FS keypads,

it is possible to install them centred to the

keyhole. The keypad flap thus also acts as

a cover for the keyhole.

Possible drilling positions for this case are

shown in Figure 2.

Anchor 7000

Installation Manual

Installation and Commissioning Manual

02 A7000-Part 2b-Installation Manual V1.04

5 / 10

Figure 2 - Drilling positions for the Primor FS

Always route the cables in such a way that

they do not come into contact with moving

parts, e.g.of theboltwork. Ensurethatthere

is no continuous movement of the cables

during operation.

Disconnect the power supply, including the power supply from the battery, before starting

work or making any changes to the wiring between the lock, keypad or signal boxes.

Anchor 7000

Installation Manual

Installation and Commissioning Manual

02 A7000-Part 2b-Installation Manual V1.04

6 / 10

Connection of an analogue keypad

As supplied, only the interface for an

analogue keypad of the AnchorPrimor

series is enabled. The serial interfaceto the

PC-based configuration of the lock and/or

to read audit information needs to be

enabled via the menu function [6].

(See the Operation Manual)

Figure 3 - Cable connection

Note:

Unlike with Anchor series locks, the serial

interface is not configured for a Primor

Signal Box. The serial interface function is

permanently set.

As the function of the signal box is fully

mapped via the plug-in terminal, there is no

need for a dual function.

UART connection

The connection via the serial interface [UART] (see above) always takes place when the

system is configured oran audit is readusingthe AnchorSELECT PC software.The connection

to the PC is made using the system cable DataCONNECT.

Outside the intended use of the serial interface (UART), i.e., reading the audit or configuring

in the setup mode, the VdS approval is no longer valid.

Analogue keypad

e.g. Primor RO

Serial interface [UART]

Connection to alarm system (plug-in terminal)

Anchor 7000

Installation Manual

Installation and Commissioning Manual

02 A7000-Part 2b-Installation Manual V1.04

7 / 10

Connection of alarm contacts

Connection via the plug-in terminal (see above) is always used if

•The lock system has an external power supply,

•A “silent alarm” contact is used to evaluate a hazard alarm system or

•A system lock is to be provided by an external signal (potential-free contact).

The connection terminal has spring-loaded

terminals. Locking is automatic when the

individual cables are inserted.

Cable cross-sections of between 0.2 mm²

and 0.5 mm² are used for flexible single

wires, and cross-sections of 0.14 mm² to

0.5 mm² for rigid cables.

According to AWG specifications, this

corresponds to cross-sections 26 to 20.

Strip 6 mm off the lines, 7.5 mm with flexible

cables.

(refer to the Phoenix Contact Combicon

data sheet)

Connecting an alarm system outside the scope of the VdS

Figure 3 shows the assignment of the

alarm interface. The signal lines can be

connected directly outside the scope of the

VdS. The signalling contacts for the silent

alarm (labelled “Duress Alarm”) and the bolt

position switch (labelled “Secure Off”) are

potential-free contacts.

(Switching capacity max. 24 V, 1 A

resistive load).We recommend considering

flyback diodes when switching high

inductive loads.

When using the alarm connection, a

regulated 12 V direct current power supply

is needed via terminals 7 (12 V DC) and 8

(GND).

Terminals 5 (“Block Sig”) and 6 (GND) need

to be bridged by a potential-free contact to

signal a signal lock. Depending on the

switching logic set (see also Operation

Manual), a connection of the contacts leads

to the system being locked or released

when the function is enabled.

Anchor 7000

Installation Manual

Installation and Commissioning Manual

02 A7000-Part 2b-Installation Manual V1.04

8 / 10

Figure 4 - Assignment of the alarm interface

You can find the configuration of the signal interfaces in the Operation Manual.

(03 Axxx –Operation Manual V3.00 Chap. 6-2 and 6-2).

If a signal lock with “release enabled” (switching logic) has been set up, this will ensure that

the lock is not automatically switched off if the control cable is cut through. At the same, a

cable breakage within the safe thus always entails the risk of a block.

Anchor 7000

Installation Manual

Installation and Commissioning Manual

02 A7000-Part 2b-Installation Manual V1.04

9 / 10

Connecting an alarm system within the scope of the VdS

In the event that an alarm connection is to

be within the scope of the VdS, the “Gator

signal plus” box known from the Gator

family must be connected between the two

via a system cable.

Figure 5 - Connection of the Gator Signal

plus

The “Gator Signal plus” box is a combined

solution with the functions of a certified

Identification number

VdS locking device

G115016

VdS hold-up detector

G115032

VdS closure monitor

G115033

It is connected by a system cable (8-pin) and plug-in adapter for the plug-in terminal.

Please refer to Part c of the Installation Manual for wiring and installation of the “Gator Signal

plus” box.

(02 P30xx-Part 2 - Signal Box Installation Manual)

Alarm system

Voltage supply

System cable with

terminal adapter

The system cable is

connected to the right

port.

Anchor 7000

Installation Manual

Installation and Commissioning Manual

02 A7000-Part 2b-Installation Manual V1.04

10 / 10

Functional test

Carry out a functional test after completion

of all assembly and installation work. With

the door open, open and close the lock

several times using the master code that

has been factory set.

The safe should open smoothly and reliably

reclose using the operating lever of the

locking mechanism. The locking control is

to be performed after each opening of the

safe.

Input of the opening code

e.g. master factory code



=✓

→



The opening code can be entered

directly without selection or similar.

The bolt is released for approx. 3

seconds after a valid code has

been entered. Open the safe within

this period after the code has been

entered.

=



Keypad test

To ensure that all numeric keys are working properly, we recommend performing a final keypad

test using function menu 5.

☼Check system menu

Press the keys in the

sequence

…



=✓

Press each numeric key once. A

functional key is indicated by a

double signal tone.

A key that is not recognised is

indicated by a long signal tone and

the functional test is cancelled. The

system must be checked.

Andere Handbücher für Anchor 7000

Inhaltsverzeichnis

Andere Wittkopp Sperren Handbücher

Wittkopp

Wittkopp Anchor 7000 Leitfaden

Wittkopp

Wittkopp Anchor 2600 Benutzerhandbuch

Wittkopp

Wittkopp 1619 Bedienungsanleitung

Wittkopp

Wittkopp BlueCam greendot Bedienungsanleitung

Wittkopp

Wittkopp Primor 1600 Benutzerhandbuch

Wittkopp

Wittkopp OPTIMA 2648 Bedienungsanleitung

Wittkopp

Wittkopp FinKey Bedienungsanleitung

Wittkopp

Wittkopp Primor 2000 / Level 5 Bedienungsanleitung

Wittkopp

Wittkopp Primor Series Bedienungsanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Wittkopp

Wittkopp Primor Level 5 Bedienungsanleitung

Wittkopp

Wittkopp Primor 2600 Benutzerhandbuch

Wittkopp

Wittkopp Primor 1000 Bedienungsanleitung

Wittkopp

Wittkopp Anchor 4000 Series Benutzerhandbuch

Wittkopp

Wittkopp Primor 1000 Benutzerhandbuch

Wittkopp

Wittkopp Primor Series Bedienungsanleitung

Wittkopp

Wittkopp Primor P30 Series Bedienungsanleitung

Wittkopp

Wittkopp Primor 3000 Bedienungsanleitung

Wittkopp

Wittkopp Primor 100 Bedienungsanleitung

Wittkopp

Wittkopp Primor Level 25 Bedienungsanleitung

Wittkopp

Wittkopp ElCom 7205 Bedienungsanleitung

Wittkopp

Wittkopp ANCHOR Bedienungsanleitung

Wittkopp

Wittkopp 7800 Bedienungsanleitung

Wittkopp

Wittkopp TwinLock 7220 Bedienungsanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung

Metra Electronics

Metra Electronics Door Access Terminal Combo Bedienungsanleitung