Wittkopp Anchor 4000 Series Bedienungsanleitung

1 / 11

Note:

On the cover sheet you can find warning information, and an explanation

of andsymbolsthe terms used, together with the exclusion of liability.

Contents

General ........................................................................................................................... 2

Code length / silent alarm ............................................................................................ 2

Battery ......................................................................................................................... 2

Interfaces .................................................................................................................... 2

Dualcode + delay time ................................................................................................. 2

Penalty time ................................................................................................................. 2

Overview of user rights ................................................................................................ 3

Open ............................................................................................................................... 3

Opening with Dualcode ................................................................................................... 3

Opening with active delay time ........................................................................................ 4

Triggering a silent alarm .................................................................................................. 4

Menu functions ................................................................................................................ 5

0 Change code ............................................................................................................ 5

1 Create user ............................................................................................................... 5

2 Blockade .................................................................................................................. 6

3 Delete user ............................................................................................................... 6

5 Check system ........................................................................................................... 6

6 System setup ............................................................................................................ 7

6-1-1 Mode change UART, serial communication .................................................... 7

6-1-2 Switch off analog keypad ................................................................................ 7

6-1-3 Activating the analog keypad and UART ........................................................ 8

6-2 Configuration of silent alarm .............................................................................. 8

6-3 Activate / deactivate external system blockade .................................................. 9

6-4 (De)Activate Dualcode ....................................................................................... 9

6-5 Battery warning threshold .................................................................................. 9

7 Overview of users ................................................................................................... 10

8 Activate setup mode ............................................................................................... 10

9 Set delay ................................................................................................................ 11

Operator

Instructions administrators user and system for

Manual 4000Wittkopp Anchor

2 / 11

General

Depending on the setup, the opening of

the lock can be subject to additional

restrictions. A combination of these

restrictions is also possible:

1. Delay time → Opening is only

possible once a defined delay

time has come to the end (with

the exception of user 9).

2. Dualcode → Opening is only

possible with two valid user

codes. (also the "two pairs of

eyes" principle )

Code length / silent alarm

Normally each user code has a length of

6 digits (0-9). If a silent alarm has been

configured, the number of code digits is

increased to 7 places. The 7th code digit

is therefore shown greyed out in the

following description.

Battery

The lock is supplied with power from a

9V block-type battery (alkaline

manganese).

A warning signal is given after code input

if the battery charge is too low. A warning

tone is repeated several times with an

alternately flashing red LED.

In such a case, change the battery as

soon as possible. The programmed

codes are retained while the battery is

changed.

Interfaces

As supplied, only the interface for analog

input units from the Primor series is

active. Other interfaces must be set via

the Setup menu.

Dualcode + delay time

If Dualcode has been activated the

opening operation corresponds to the

described opening procedure after the

end of the delay time.

Only "user 9" can open by himself with an

active Dualcode condition ("two pairs of

eyes" principle)

during the delay time. A Dualcode

condition arises through the fact that

under 9 alone cannot start the delay time.

An invalid code input during the release

time means that the operation is

terminated and the delay time must be

started again.

The input of a valid code during the

opening delay is acknowledged positively

but has no effect in itself.

An opening delay time that has been

started can be stopped by pressing any

key.

Penalty time

A penalty time of 5 minutes is imposed

after 4 invalid code inputs. Until a valid

code is input, a penalty time is imposed

again after two incorrect inputs.

3 / 11

Overview of user rights

Open

e.g. factory code Master





=

→



The opening code can be input

directly as described above, without

selection. After a valid code is

input, the lock releases the bolt

movement for around 3 seconds.

Open the safe within this time after

inputting the code.

=

Opening with Dualcode

e.g. user 3 begins the input of his code with code

030303 If there is an incorrect input or if

more than 30 seconds elapse

between the two code inputs then

the inputting is terminated with a

long signal tone.





=

=

The two pairs of eyes principle, here user 5 with code

0505050, initiates the opening operation





=

→



=→

Factory code

Open

Start delay time

Quick opening code

Create user

Change code

Delete user

Initiate operating

blockade

Check system

System setup

Overview of users

Set delay time

Master 23456(0)  

User 0...8 -   

User 9 -    

4 / 11

Opening with active delay time

Start through code input





=

→



If a delay time has been

programmed, this must be started

first by inputting a valid opening

code. It can then be opened by

inputting any desired valid user

code during the time window for

opening.

User 9 cannot start the delay, but

instead can open before the end of

the delay time.

=

♪…2 sec…♪…2 sec…♪…2

sec…



♪…1 sec…♪…1 sec…♪…1

sec…



Input the code for opening





=

→



=→

Triggering a silent alarm

e.g. opening code 1234567, alarm addend 2

Start through code input





=

→



The last code digit is amended in

each case with active "silent

alarm". The calculation is done on

the basis of the last digit + alarm

addend. If a number is carried over

then the units are evaluated:

e.g. code number 9 + alarm

addend 2 = 11, hence the last

number is = 1

→



=→

The locking check can be done via the operating lever of the boltwork and should be

performed after each closing and locking.

5 / 11

Menu functions

If there is a rejection at the end of a menu step (long signal tone) then the procedure is

terminated and the menu function is quit.

0 Change code

e.g. change 1234560to 1111111

 ☼ Change menu code

Input code, e.g.





=

Both the user code and the master

code can be amended by using the

Change function.

Input the new code





=

Confirm the new code





=

Code was amended successfully

1 Create user

e.g. create user No. 3

 ☼ Menu Create user

Input the master code





=

A new user code is only accepted if

the code differs at two places by

one digit from an existing code.

If an opening delay has been

programmed, user 9 for the

immediate opening code can only

be created in the opening release

time.

This of course only applies if this

had not already been created

before the activation of the delay

time.

Number of the user to be

created





=

Input user code, e.g.





=

Confirm the user code





=

In the case of an active Dualcode a valid user input must be input before jumping to a menu.

The menu selection is only done afterwards.

6 / 11

2 Blockade

 ☼ Menu Blockade All users can be blocked or

released with this function. All

codes are retained.

Input the master code





=

All users are activated / deactivated

3 Delete user

e.g.delete user No. 2

 ☼ Menu Delete user

Input the master code





=

The master can delete a user. It is

not possible to delete the master.

Number of the user to be

deleted





=

5 Check system

 ☼ Checking the menu system

Press the keys in the

sequence

 …



=

Press each numeric key once. A

functional key is indicated by a

double signal tone.

A key that is not recognised is

indicated by a long signal tone and

the function test is terminated.

The system must be checked.

If Dualcode is active the user who made the jump to the menu possible with a code input

cannot be deleted.

7 / 11

6 System setup

6-1-1 Mode change UART, serial communication

Switch off UART to be able to use IO

 

☼

Menu System setup

Input the master code





=

Since switching of the operating

mode can under certain

circumstances also have a major

influence on the function of the

input unit, the general sequence for

the menu function was amended

intentionally.

This should make it more difficult to

switch mode accidentally.

Submenu Mode change





=

Mode IO





=

Input the master code





=

Mode IO





=

6-1-2 Switch off analog keypad

 ☼ Menu System setup

Input the master code





=

!!! Warning !!!

Once the analog keypad has been

switched off it can only be activated

again via the serial interface!

Since switching of the operating

mode can under certain

circumstances also have a major

influence on the function of the

input unit, the general sequence for

the menu function was amended

intentionally.

This should make it more difficult to

switch mode accidentally.

Submenu Mode change





=

Mode only UART





=

Input the master code





=

Mode IO





=

Locks of the Anchor series have in addition to the connection for an analog keypad an

additional interface that can be used for serial communication [UART] or to connect a signal

box (e.g. from the Primor series) [IO]. The operating mode must be set correspondingly

before use.

8 / 11

6-1-3 Activating the analog keypad and UART

 ☼ Menu System setup

Input the master code





=

Since switching of the operating

mode can under certain

circumstances also have a major

influence on the function of the

input unit, the general sequence for

the menu function was amended

intentionally.

This should make it more difficult to

switch mode accidentally.

Submenu Mode change





=

Mode analog + UART





=

Input the master code





=

Mode analog + UART





=

6-2 Configuration of silent alarm

Set the alarm addend, e.g. the last code digit + 3

 ☼ Menu System setup

Input the master code





=

The "silent alarm function" is

deactivated by inputting the number

0 as the alarm addend.

The quiescent state of the

switching contact is defined by the

switching logic.

high = relay switches on briefly if

there is an alarm

low = relay switched to quiescent

state. If there is an alarm it is

switched off briefly

Submenu "silent alarm"





=

Alarm addend





=

Switching logic 1=high,

0=low

or 



=

Activation of the "silent alarm function" increases the number of code digits that are

required from 6 to 7 places. (Requirement for code differentiation VdS)

If users have already been created, the last place is automatically filled with 0.

The user codes should therefore be changed subsequently!

9 / 11

6-3 Activate / deactivate external system blockade

Activate the blockade by an external signal

 ☼

Menu System setup

Input the master code





=

The basic setting is "deactivated"

after activating the IO.

The quiescent state of the control

input is defined by the switching

logic:

high = the system is blocked if a

signal is present.

low = the system is blocked and

must be released by the signal.

Submenu System blockade





=

activate=1, deactivate=0



or 



=

Switching logic 1=high,

0=low



or 



=

6-4 (De)Activate Dualcode

Activate / deactivate the Dualcode

 

☼

Menu System setup

Input the master code





=

The Dualcode only becomes active

once at least a second user has

been defined.

A valid opening code must be input

before the menu start to be able to

deactivate the function.

Submenu Dualcode





=

activate=1, deactivate=0



or 



=

6-5 Battery warning threshold

Amend the battery warning threshold to, for example,

5.67 V

 

☼

Menu System setup

Input the master code





=

The lock system can be adapted to

various kinds of batteries through

the parametrisation of the warning

threshold.

The preset value is 5 V. The

warning threshold can be set

between 5000 mV and 8000 mV.

Submenu Battery warning





=

Threshold value in mV





=

10 / 11

7 Overview of users

 ☼ Menu Overview query users

Input the master code





=

This function gives an overview of

the number of free and already

occupied users.

It is possible to check selectively

whether one or more specific users

have already been created.

User number to be checked

,,...

♪



= free

= occupied

End the query





=

8 Activate setup mode

 ☼ Menu Activate setup mode

Input the master code





=

Setup mode is used to parametrise

the functions "Create user", "Delete

user" or delay times.

Submenu Setup mode





=

Setup mode is terminated automatically if keypad input is cancelled due to the time being

exceeded, at the end of a menu sequence without restarting a menu, or by interrupting the

power supply.

Andere Handbücher für Anchor 4000 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Wittkopp Sperren Handbücher

Wittkopp

Wittkopp Primor Series Bedienungsanleitung

Wittkopp

Wittkopp Primor 1000 Benutzerhandbuch

Wittkopp

Wittkopp Primor 3000 Bedienungsanleitung

Wittkopp

Wittkopp GATOR F Bedienungsanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Wittkopp

Wittkopp ElCom 7205 Bedienungsanleitung

Wittkopp

Wittkopp Primor Level 5 Bedienungsanleitung

Wittkopp

Wittkopp Primor Series Bedienungsanleitung

Wittkopp

Wittkopp BlueCam greendot Bedienungsanleitung

Wittkopp

Wittkopp SmartCam Bedienungsanleitung

Wittkopp

Wittkopp Primor P30 Series Bedienungsanleitung

Wittkopp

Wittkopp Anchor 2600 Benutzerhandbuch

Wittkopp

Wittkopp Primor 2600 Benutzerhandbuch

Wittkopp

Wittkopp Primor 1000 Bedienungsanleitung

Wittkopp

Wittkopp Primor 2000 / Level 5 Bedienungsanleitung

Wittkopp

Wittkopp Primor 100 Bedienungsanleitung

Wittkopp

Wittkopp Anchor 4000 Series Benutzerhandbuch

Wittkopp

Wittkopp 7800 Bedienungsanleitung

Wittkopp

Wittkopp Anchor 7000 Leitfaden

Wittkopp

Wittkopp Primor 1600 Benutzerhandbuch

Wittkopp

Wittkopp OPTIMA 2648 Bedienungsanleitung

Wittkopp

Wittkopp TwinLock 7220 Bedienungsanleitung

Wittkopp

Wittkopp Primor Level 25 Bedienungsanleitung

Wittkopp

Wittkopp Anchor 7000 Bedienungsanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung

Metra Electronics

Metra Electronics Door Access Terminal Combo Bedienungsanleitung