X-Rite DTP32 Bedienungsanleitung

X-Rite World Headquarters © 1995 X-Rite, Incorporated Doc# DI00012a.doc

(616) 534-7663 Fax (616) 534-8960 August 18, 1995

Interfacing the DTP32/DTP12 with the Seiko DPU-411 Thermal Printer

To interface the DTP unit to send output to a Seiko DPU-411 Thermal Printer, you must first

set-up three things: 1) connect the two devices with the correct cabling and adapters, 2) set

the dip switches on the DPU-411 correctly, and 3) configure the communications set-up on the

DTP unit.

Cabling

To connect the DTP32 or DTP12 to the Seiko printer you will need a 418-69 cable and a 418-

80 converter from X-Rite. Plug the 418-80 into the RS 232 port in the back of the Seiko

Printer. Next plug the cable in; one end to the DTP unit, the other to the adapter plugged into

the printer. It will not matter which end goes to which device.

Setting the DPU's Dip Switches

Next you must set the dip switches found on the bottom of the Seiko DPU-411 Thermal

Printer. Turning the printer over you will notice two sets of dip switches. The first set of

switches are labeled 1 through 8. The second set is labeled 1 through 6. Switches pushed up

(towards the word "ON") are on, while switches in the down position are off. Set the switches

as follows:

1: OFF 1: ON

2: OFF 2: ON

3: ON 3: OFF

4: ON 4: OFF

5: OFF 5: ON

6: OFF 6: ON

7: ON

8: ON

Configuring the DTP

To configure the DTP unit we must go to the configure menu. Start by pressing the two right-

most buttons on the DTP unit at the same time. This will get you to Page one of the MAIN

MENU. Now press the left-most button twice to scroll you to page 3 of the Main Menu. The

display should read "p3 cnfg edit". Press the button under the word "cnfg" to enter the configu-

ration menu.

®

Interfacing the DTP32/DTP12 with the Seiko

DPU-411 Thermal Printer

Author - Michael DiCosola

X-Rite World Headquarters © 1995 X-Rite, Incorporated Doc# DI00012a.doc

(616) 534-7663 Fax (616) 534-8960 August 18, 1995

Check the following fields to ensure proper communication:

•Press the button under the word "TYPE". If "TYPE" does not change to "ser", continue to

press the same button until it does read "ser".

•Press the left-most button to continue.

•Press the button under the word "BAUD". If "BAUD" does not change to "1200", continue

to press the same button until it does read "1200".

•Press the button under the word "HAND". If "HAND" does not change to "xon", continue to

press the same button until it does read "xon".

•If the last word on the display, "axmt", is spelled in all capital letters, press the button be-

neath "AXMT" until the word changes from capital letters to lower case letters.

•Press the left-most button to continue.

•Press the button under the word "DLIM". If "DLIM" does not change to "crlf", continue to

press the same button until it does read "crlf".

•Press the two left-most buttons at the same time to save these configuration settings.

Sending Data to the Printer

After reading an auto scannable test strip the DTP will automatically display your readings.

Use the up or down arrows to view the separate reading of each strip. Use the right most but-

ton to toggle between different strips if you scanned more than one strip. Pressing the button

under the word "xmit" will transmit your data to the Seiko printer. The word will temporarily

change to all capitals and the Seiko will begin printing your output.

Dieses Handbuch passt für folgende Modelle

1

Inhaltsverzeichnis

Andere X-Rite Messgerät Handbücher

X-Rite

X-Rite MA94 Bedienungsanleitung

X-Rite

X-Rite PANTONE i1 PRO 3 PLUS Bedienungsanleitung

X-Rite

X-Rite VeriColor Spectro Bedienungsanleitung

X-Rite

X-Rite X-RiteColor DTP34 Bedienungsanleitung

X-Rite

X-Rite i1Pro Bedienungsanleitung

X-Rite

X-Rite 552 Bedienungsanleitung

X-Rite

X-Rite Ci7860 Series Bedienungsanleitung

X-Rite

X-Rite Ci51 Bedienungsanleitung

X-Rite

X-Rite DensiEye 700 Bedienungsanleitung

X-Rite

X-Rite Ci61 Bedienungsanleitung

X-Rite

X-Rite MA-T6 Bedienungsanleitung

X-Rite

X-Rite COLOREYE XTH Bedienungsanleitung

X-Rite

X-Rite BASF 12/6 Bedienungsanleitung

X-Rite

X-Rite Color i7 Bedienungsanleitung

X-Rite

X-Rite VeriColor Installationsanleitung

X-Rite

X-Rite DigiMatch PPG Bedienungsanleitung

X-Rite

X-Rite DensiEye 100 Bedienungsanleitung

X-Rite

X-Rite SP52 Bedienungsanleitung

X-Rite

X-Rite i1Studio Bedienungsanleitung

X-Rite

X-Rite SP60 Series Bedienungsanleitung

X-Rite

X-Rite EyeOne Pro Bedienungsanleitung

X-Rite

X-Rite MA-5 QC Bedienungsanleitung

X-Rite

X-Rite vipFLEX2 Bedienungsanleitung

X-Rite

X-Rite RM61 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung