X-Vision VIS338D Bedienungsanleitung
CCTV
Model: VIS338D
Colour Varifocal Dome
Camera
CCTV
Model:
VIS338D
Colour Varifocal Dome Camera
Manufactured exclusively for:
Xvision (Europe) Group,
Head Office: London, U.K.
Email: [email protected].uk
Web: www.x-vision.co.uk
TECHNICAL SUPPORT:
For Technical Support for any Xvision product please contact your local
distributor.
LIMITED WARRANTY:
This product is supplied with a 2 Year warranty. The Warranty excludes
products that have been misused, (including accidental damage) and
damage caused by normal wear and tear. In the unlikely event that you
encounter a problem with this product, it should be returned to the
place of purchase.
Beforeyou begin
•Please unpack the box carefully and identify that all the parts are present.
•Do not cut the camera cables, this will void the warranty.
•Make sure you use only the recommended power supply. Damage caused to the camera by
incorrect voltage or wiring is not covered by the warranty.
The camera is suitable for indoor or outdoor use. Please bear in mind the following points when
choosing a mounting position.
•The camera must be positioned so that it will not point directly into the sun (sunrise and
sunset) or any bright light, as this may cause damage to the camera.
•Avoid viewing areas where half the area is in bright sunlight and the other half is dark,
such as in the shadow of a building. All types of cameras have difficulty in ‘seeing’ with
such a large lux level variation.
Specifications
Model: VIS338D
Picture Type: Colour
Image Sensor: Sony 1/3” HQ1 Super HAD CCD
DSP: Xvision IXC1HQE
Resolution: 550 TVL
Lens Viewing Angle: 23 to 90°
Infra Red Nightvision: No
Minimum Illumination: 0.2 Lux
Audio: No
Operating Voltage: 12V DC 145mA
Suggested Power Supply: 12V DC 300mA Regulated
Mounting: Ceiling
Weatherproofing: No
Dimensions (ØxD): 140x81mm
THANK YOU VERY MUCH FOR PURCHASING OUR PRODUCT
The VIS338D colour varifocal dome camera is designed for high risk
applications. It offers super high resolution 550 TVL images from its
Sony 1/3" HQ1 Super HAD CCD sensor and Xvision Pixel+ Varifocal lens
which allows easy selection of the optimum viewing angle required
during installation, and will provide images in light levels as low as 0.2
lux. The camera is designed for internal use and ceiling mounting.
•Super High Resolution CCD sensor provides great quality Colour images
in light levels of 0.2 lux and above
•Discreet styling for unobtrusive low profile use
•Tamper resistant and easy to clean as all moving parts are behind the
dome cover
•Sony 1/3" HQ1 Super HAD CCD image sensor for 550 TVL resolution
images and 0.2 lux low light sensitivity
2. Product Description
Package Contents
1. Instruction Manual
2. VIS338D Dome Camera 3. Plastic Bag- containing
4x fixing screws,
1x retaining screw
1 2 3
3. Features
7DIP Switch Setting
7.1 Flickerless Function- Set switch -OFF/FL to Flicker to enable
flickerless function. In this mode the switch AES/OFF is auto
disabled.
7.2 AGC-Hi/AGC-Lo Function- Adjusting the switch to AGC indicates
AGC-Hi and in the OFF position indicates AGC-Low. In AGC-Hi
mode, the maximum AGC gain is approximately 26dB. In AGC-Lo
mode, the maximum AGC gain is approximately 16dB.
7.3 Auto Iris Function- When using an Auto Iris lens the switch
AES/OFF should be in the OFF position to disable the AES
function. Adjust the LEVEL with the VR to the proper level.
7.4 BLC Function- Set switch OFF/BLC to BLC position to enable
Back Light Compensation (BLC) function
F.L.: Flickerless On/OFF
AGC:Auto Gain Control High/Low
AES: Auto Electronic Shutter
LLC: Back Light Compensation
VR Adjustment Level for DC Drive Lens
Inside Control Board
(Colour Normal Resolution)
•Xvision IXC1HQE Digital Signal Processing (DSP) chip which has been
optimised for internal viewing and features Automatic Gain Control,
Automatic Electronic Iris, Auto White Balance, Back Light Compensation,
Low Smear, Edge Enhancement and Zero Colour Rolling
•Xvision Pixel+ Varifocal 3.3 to 12.0mm Auto Iris lens with 23° to 90°
viewing angle for super sharp images and easy selection of the
optimum viewing angle during installation
•Designed for internal use and ceiling mounting
STEP 1: Select a suitable position on the ceiling to install the camera.
STEP 2: Rotate the dome housing counterclockwise to remove it from
the mounting base (as shown in Figure 1).
STEP 3: Position the mounting base on to the ceiling and centre it over the
mounting hole. Fix with the four fixing screws (supplied). Allow the cable
connnectors to pass through (as shown in Figure 2).
Figure 1
Installation
STEP 6:
6.1 Connect the Video Output to the monitor or other video device
through a 75 Ohms type coaxial cable.
6.2 Connect the DC Jack or AC/DC Terminator with the power source.
6.3 Once the picture appears on the monitor, open the cover and make
the Zoom Adjustment by rotating the screw (NEAR-Anti-clockwise,
FAR-Clockwise) until you get the desired view. Next make the Focal
Adjustment by rotating the screw (TELE-Anti-clockwise, WIDE-
Clockwise) until you get the desired view. After adjustment tighten both.
STEP 4: Set the final image position by moving the camera body (some
model types limit the PCB board to 180° rotational
adjustment) and set the focus by turning the lens to the left or
right. When the camera focus adjustment is complete, replace
the dome housing by rotating clockwise to secure it (as shown
in Figure 3).
STEP 5: Secure the dome to the base of the camera by using the retaining
screw supplied (as shown in Figure 4).
Figure 3
Figure 4
Figure 5
Figure 2
Figure 6
Inhaltsverzeichnis
Andere X-Vision Sicherheitskamera Handbücher
X-Vision
X-Vision Professional NPR Camera Einrichtungshandbuch
X-Vision
X-Vision XPD421DNV Bedienungsanleitung
X-Vision
X-Vision VIS200DX-2 Bedienungsanleitung
X-Vision
X-Vision VIS238D Bedienungsanleitung
X-Vision
X-Vision XIR621 Bedienungsanleitung
X-Vision
X-Vision XSD27ZS Bedienungsanleitung
X-Vision
X-Vision CVR811 Bedienungsanleitung
X-Vision
X-Vision XSD27ZIR Bedienungsanleitung
X-Vision
X-Vision XC960VA Bedienungsanleitung
X-Vision
X-Vision XPT600 Bedienungsanleitung
X-Vision
X-Vision XSD27ZDN Bedienungsanleitung
X-Vision
X-Vision VIS249D Bedienungsanleitung
X-Vision
X-Vision VIS249D-2 Bedienungsanleitung
X-Vision
X-Vision XHC1080S10IRN Bedienungsanleitung
X-Vision
X-Vision XSD27ZIR-2 Bedienungsanleitung
X-Vision
X-Vision XIR538 Bedienungsanleitung
X-Vision
X-Vision XC960DA Bedienungsanleitung
X-Vision
X-Vision VIS249DX Bedienungsanleitung
X-Vision
X-Vision VIS449E Bedienungsanleitung
X-Vision
X-Vision VIS200DX-3 Bedienungsanleitung
