X-Vision XSD27ZIR-2 Bedienungsanleitung

XSD27ZIR-2 Operating Manual

Contents

1. PRODUCT INTRODUCTION

1.1 FEATURES …………………………………………………………………………………….……………….…3

1.2 FUNCTION …………………………………………………………………………………………………….... 4

1.3 PACKAGED CONTENTS …………………………………………………………………………..……..…. 4

2. INSTALLATION

2.1 INSTALLATION WARNING …………………………………………..…………………………..…..…… 5

2.1 WIRING …………………………………………………………………………………………….…………….. 7

3. BASIC OPERATION

4. MENU SETTINGS

4.1 MAIN MENU ……………………………………………………………………………………………..……. 8

4.2 SYSTEM INFORMATION …………………………………………………………………….……………. 10

4.3 ADDRESS SETTING ……………………………….…………………………………………………………. 10

4.4 MOTION ………………………………………………………………………………………………………... 11

4.5 PATTERNS …………………………………………………………………………………………..…………. 13

4.6 CAMERA …………………………..…………………………………………………………………………… 14

4.7 CRUISE SETTING …………………………………...……………….………………………………………. 14

4.8 ALARM SETTING ………………………………………………..…………………………………………… 15

4.9 DISPLAY SETUP ………………………………………………………..………………….…………………… 15

4.10 IR SETTING …………………………………………………………..……………………………………… 16

5. TROUBLESHOOTING

5.1 TROUBLE SHOOTING TABLE …………………………………………….……………………………… 17

XSD27ZIR-2 Operating Manual

1. PRODUCT INTRODUCTION

1.1 FEATURES

Strong Intelligence Function:

Compatible with PELCO D/P, HIKVISION and DAHUA Multi-protocol

Recognizes 2400, 4800, 9600 Baud Rate

Automatic recognition for RS 485 control protocol

Support 3D Positioning Function for the HIKVISION and DAHUA DVR

Strong Horizontal and Vertical Rotation Function:

Complete 360 degree° rotation

High speed Pan Tilt rotation

Based on vector drive technology that ensures the Pan & Tilt motion takes the most

efficient and shortest path when viewing presets

Features an advanced micro-stepping motor that allows the Pan/Tilt rotation reach

speeds of 0.05 degree/sec. This allows the video image to be more accurate and

stable under high magnification times.

Presets, Cruises Scan, Zones Scan, Continuous Scan

Maximum 256 presets (every preset includes lens magnification and angle position)

It may record up to 4 cruise presets (100 units of motion per cruise)

Set up the left and right border of specified zones

Pan Tilt Zoom functions can be executed at specified speeds

A preset can include a continuous 360° scan

On Screen Display (OSD) Menu

Built-in OSD screen menu that allows you to easily access and modify the speed

dome’s parameters

Horizontal/Vertical angle and operating magnification of lens and presets can be

displayed on screen

PTZ Control

Adopts RS485 protocols

Complete 360° horizontal rotation and 90° vertical rotation allows surveillance

without any blind spots

XSD27ZIR-2 Operating Manual

1.2 FUNCTION

Setup of address code:

The XSD27ZIR-2 allows the user to manually set the camera’s protocol such as its network

address, baud rate and RS485 protocol. Additionally the speed dome camera has the

ability to recognize the camera address, baud rate and control protocol automatically.

Automatic turnover:

When the camera reaches its maximum tilt position, by continuing the movement on a

PTZ controller, the lens will automatically flip 90° and rotate 180° horizontally. Therefore

the user will not have to scroll all the way back to the opposite viewing angle, allowing

them to a achieve 180 ° continuous surveillance.

Reserve and call preset:

Users can store up to 256 presets which can be set via the speed dome itself or via a

compatible controller

Lens Control:

The cameras lens can be fully controlled via a PTZ controller such as the zoom and focus.

Additionally if you want to reset the auto-focus the user can simply shake the PTZ

controller’s joystick or set up a preset.

Iris Control:

User can manually adjust the iris via using the PTZ joystick/controller to their desired

requirements.

Night vision:

The Speed Dome will automatically switch to its nightvision mode once the illumination

levels drop to a certain level. This will power up the IR LEDs and will provide a clear black

and white image.

Auto-Cruise:

The speed dome can be programmed to set up various presets that allow the user to set

up various patterns

Patterns:

The camera can store up to 4 different patterns which can then be auctioned by the PTZ

controller as predefined presets (i.e. numbers 84, 85, 86, and 87)

1.3 PACKAGE CONTENTS

The packaged box for the XSD27ZIR-2 comes with the following items:

XSD27ZIR-2 Speed Dome Camera (x1)

24v Power Supply (x1)

Protective Gloves (x1)

Screws (x4)

Allen key (x1)

Should any of these items be missing please contact your local distributor.

XSD27ZIR-2 Operating Manual

2. Installation Instruction

Warnings

This symbol on the product or on its packaging indicates that this product should not be

treated as household waste. Instead, you should make arrangements for the recycling of this

unit.

By ensuring this product is disposed of correctly, you will help to prevent harm to the

environment, and avoid possible health issues, which may be caused by inappropriate waste

handling of this product.

The recycling of materials helps to conserve our natural resources. For more detailed

information about recycling of this product, please contact your local council office, your

household waste disposal service or the shop where you purchased the product. In addition

you can find further information online at www.environment-agency.co.uk

WARNING: This symbol is intended to alert the user to the presence of

non-insulated “dangerous voltage”.

CAUTION: This symbol is intended to alert the user to presence of

important operating and maintenance (Servicing) instructions in the

literature accompanying the appliance.

Disposal of Old Electrical & Electronic Equipment (Applicable in the

European Union and other European countries with separate collection

systems- WEEE).

XSD27ZIR-2 Operating Manual

Prior to installation and use of this product, please observe the following points:

Installation and servicing should be carried out by qualified service personnel.

It is important that the dome camera is not left in a position where the camera is

pointing directly at the sun or other extremely bright light source. This may result in CCD

damage and poor image quality.

The installation position must be as far away from high voltage sources as possible.

Dome cover is high quality optical product- Try to avoid touching it as any scratches or

marks left on the surface could affect image quality (we recommend the use of cotton

gloves when handling). Please refer to the installation manual for further guidance

In order to get the optimum image at all times, the dome cover should be cleaned

periodically. Be careful when cleaning; only hold the cover edge, avoiding direct contact

with the dome cover. Acid from fingerprints will damage the coated surface of the dome

cover. Direct contact with hard objects could lead to deterioration of the image. Please

use a soft clean cloth or similar to clean interior and exterior surfaces of the cover. A

neutral detergent or high-grade furniture detergent may be used.

Only use replacement parts recommended by your local distributor.

After replacement/repair of this unit’s electrical components, take a resistance

measurement between line and exposed parts to verify the exposed parts have not been

connected to line circuitry.

The installation method and materials should be capable of supporting four times the

combined weight of the camera and bracket.

When unpacking the dome, the Pan/Tilt module should be handled with care. Do not

place in a position where something could rub against or fall onto the housing.

When installing camera module, avoid touching any parts which could be easily damaged,

such as the optics and PCB.

Make sure all power and telemetry connections are complete before powering up the

camera.

XSD27ZIR-2 Operating Manual

2.1 Wiring

2.1.1 Power supply connection

Please check the voltage rating and electric current:

Voltage Rating

Range of Voltage Rating

Electric Current

AC 24V / DC 24V

±5%

Connection of control cable

PTZ control: connect RS-485 cable to PTZ control keyboard or DVR. If you control more

than one camera the RS-485 cable needs to be run in parallel position

Protocol and baud rate of PTZ control keyboard or DVR can be set optionally

If you have more than 1 dome please set incremental addresses for each camera

Video Connection

Use BNC plug to connect video signal cable.

Power supply: DC 24V 2A interface

Control cable: RS485 control

Video cable: BNC interface

Please note:

Handle with care whilst installing the camera ensuring that none of the moving

parts are damaged.

Use shielded cable and do not mix with other cables.

Keep the PTZ dome camera or signal transmission cable away from high voltage

equipment or cables (at least 50 meters) and ensure that is lightning and surge

protection

Do not use the PTZ dome camera in environments of extreme temperature or

humidity. The temperature should be between -25 ° and 50° with humidity <90%

XSD27ZIR-2 Operating Manual

3. BASIC OPERATIONS

To control the PTZ functions on a speed dome you will need use a compatible PTZ

joystick/keyboard controller. These instructions are based upon Xvision’s XSDZ-3DM Speed

Dome Joystick controller.

When you turn on the power for speed dome it will begin to initialise and the monitor will

display the following information:

Input <95>and then press the <PRE> (CALL) button to bring up the OSD main menu which

will be displayed as follows:

Move the PTZ joystick (i.e. up/down directions) to navigate the menu’s contents

Press the <OPEN> button to enter the chosen menu item. The <OPEN> button can also be

used to select and save changes to parameters within the specific menu items.

Press the <CLOSE> button to exit the OSD menu.

Additionally navigate to the BACK option within the menus and then press the <OPEN>

button to go back to the previous menu/page.

To exit the menu navigate to the bottom of the main menu and select the EXIT option

and then press the <OPEN> button to exit the OSD menu.

PTOL: Auto

COMM: Auto

ADDR: 1

Please Note: PTZ joystick/Controller manufacturers may have different operational

configurations. Please refer to the manufacturer’s operating manual for further details.

MAIN MENU

SYSTEM INFORMATION

ADDR SETTING

MOTION

PATTERNS

CAMERA

CRUISE SETTING

ALARM SETTING

DISPLAY SETUP

IR SETTING

RESTORE FACTORY DEFAULT

REBOOT SYSTEM

EXIT

XSD27ZIR-2 Operating Manual

The XSD27ZIR-2 is designed to recognise the following presets:

SPECIAL PRESETS

FUNCTION

95 + CALL

Enter main menu

XXX + PRESET

Reserve preset xxx

XXX + CALL

Call preset xxx

83 + CALL

Delete all presets

84 + CALL

Call pattern 1

85 + CALL

Call pattern 2

86 + CALL

Call pattern 3

87 + CALL

Call pattern 4

96 + PRESET

Select different camera core

96 + CALL

360° gap scanning

98 + CALL

360° continuous scanning

99 + CALL

Presets Cruise

4.1 Main Menu

The items in the main menu are listed below as follows:

SYSTEM INFORMATION: Displays the camera’s general information

ADDR SETTING: Camera’s operating protocols

MOTION: PTZ Movement Settings

PATTERNS: Configure Patterns

CAMERA: Configure settings for the lens

CRUISE SETTING: Configure Cruises

ALARM SETTING: Configure actions for alarms

IR SETTING: Configure settings for IR LEDs

RESTORE FACTORY DEFAULT: Restores the factory default setting

REBOOT SYSTEM: Reboot the camera

EXIT: Exit the OSD menu

XSD27ZIR-2 Operating Manual

4.2 SYSTEM INFORMATION

The System Information option displays the speed domes general operating parameters and

information and is displayed as follows:

The System Information menu items are explained as follows:

COM: Baud Rate, Parity Bit, Date Bit and Stop Bit

ADDRESS: Camera ID for PTZ control (i.e. between 0-255)

SOFTWARE VERSION: Current software version

BACK: Returns back to the previous menu

EXIT: Exits the main menu

4.3 ADDRESS SETTING

The address setting menu is displayed as follows:

The speed domes address type (ADDR TYPR) can set between either SOFT (automatically

obtains an address) or HARD (address is physically set via the dip-switches). Once selected

press the <OPEN> button to save any changes. Similarly uses the joystick to scroll through the

other options to set either the ADDR SOFT or ADDR HARD).

Once completed you can select BACK or EXIT options to leave the setup.

SYSTEM INFORMATION

COM 9600, N, 8 ,1

ADDRESS 1

SOFTWARE VERSION V5.2

BACK

EXIT

ADDR SETTING

ADDR TYPE HARD

ADDR SOFT 255

ADDR HARD 1

BACK

EXIT

Please Note: The options described with the System Information cannot be changed

within this menu

Andere Handbücher für XSD27ZIR-2

Inhaltsverzeichnis

Andere X-Vision Sicherheitskamera Handbücher

X-Vision

X-Vision XC960BA Bedienungsanleitung

X-Vision

X-Vision XSD27ZIR Bedienungsanleitung

X-Vision

X-Vision XIR501 Bedienungsanleitung

X-Vision

X-Vision XSD27ZDN2 Bedienungsanleitung

X-Vision

X-Vision XSD27ZIR-2 Bedienungsanleitung

X-Vision

X-Vision XP1080B Bedienungsanleitung

X-Vision

X-Vision VIS430R Leitfaden

X-Vision

X-Vision XC960DA Bedienungsanleitung

X-Vision

X-Vision Professional NPR Camera Einrichtungshandbuch

X-Vision

X-Vision XPD421DNV Bedienungsanleitung

X-Vision

X-Vision XPD700W-2 Bedienungsanleitung

X-Vision

X-Vision XSD27ZS Bedienungsanleitung

X-Vision

X-Vision XSD27ZIR-2 Bedienungsanleitung

X-Vision

X-Vision PCC422E Bedienungsanleitung

X-Vision

X-Vision XSD27ZDN Bedienungsanleitung

X-Vision

X-Vision XSD27ZS Bedienungsanleitung

X-Vision

X-Vision XPS036 Bedienungsanleitung

X-Vision

X-Vision VIS449E Bedienungsanleitung

X-Vision

X-Vision XAM202-208 Bedienungsanleitung

X-Vision

X-Vision VIS249D Bedienungsanleitung

X-Vision

X-Vision XIR621 Bedienungsanleitung

X-Vision

X-Vision XC960BN Bedienungsanleitung

X-Vision

X-Vision VIS238D Bedienungsanleitung

X-Vision

X-Vision VIS200DX-3 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung