X-Vision XSD27ZIR-2 Bedienungsanleitung

XSD27ZIR-2

Day/Night 600 TVL

IR Speed Dome CCTV Camera

27x Optical Zoom

and 100m Nightvision

User Manual

XSD27ZIR-2 - User Manual

Contents

1. PRODUCT INTRODUCTION

1.1 FEATURES …………………………………………………………………………………….……………….… 3

1.2 FUNCTIONS ………………….……………………………………………………………………………….... 4

1.3 PACKAGED CONTENTS …………………………………………………………………………..……..…. 4

2. INSTALLATION

2.1 INSTALLATION WARNING …………………………………………..…………………………..…..…… 5

2.3WIRING …………………………………………………………………………………………….…………….. 8

3. OPERATING BASICS

4. MENU SETTINGS

4.1 MAIN MENU ……………………………………………………………………………………………..……. 10

4.2 SYSTEM INFORMATION …………………………………………………………………….……………. 11

4.3 ADDRESS SETTING ……………………………….…………………………………………………………. 12

4.4 MOTION (PAN/TILT SETTINGS) …………..………………………………………………….………... 11

4.5 PATTERNS …………………………………………………………………………………………..…………. 13

4.6 CAMERA …………………………..…………………………………………………………………………… 14

4.7 CRUISE SETTING (Tour) ….……………………...……………….………………………………………. 14

4.8DISPLAY SETUP ………………………………………………………..………………….…………………… 15

4.9IR SETTING ………..……………………………………………………..………………….…………………… 15

5. TROUBLESHOOTING

5.1 TROUBLE SHOOTING TABLE …………………………………………….……………………………… 15

XSD27ZIR-2 - User Manual

1. PRODUCT INTRODUCTION

1.1 FEATURES

Advanced Pan Tilt Zoom functionality:

Automatic recognition for RS 485 control protocol

Recognizes 2400, 4800, 9600 Baud Rate (Compatible with PELCO D/P protocols).

Complete 360 degree° rotation and 90° vertical rotation allows surveillance without

any blind spots

High speed Pan Tilt rotation

Based on vector drive technology that ensures the Pan & Tilt motion takes the most

efficient and shortest path when viewing Presets

Features an advanced micro-stepping motor that allows the Pan/Tilt rotation reach

speeds of 0.05 degree/sec. This allows the video image to be more accurate and

stable under high magnification times.

Presets and Tours

Maximum of 256 Presets (every Preset includes a lens magnification and viewing

angle position)

Records up to 1 predefined tour (which consists of a maximum of 20 Presets)

Set up the left and right border of specified zones

Execute Pan Tilt Zoom functions at specified speeds

A Preset can include a continuous 360° scan

On Screen Display (OSD) Menu

Built-in OSD screen menu that allows you to easily access and modify the speed

dome’s operating parameters/settings

Operating information such as horizontal/vertical viewing angle, magnification of the

lens and Preset in use, can be displayed on screen for the operator.

XSD27ZIR-2 - User Manual

1.2 FUNCTIONS

Setup of address code:

The XSD27ZIR-2 allows the user to manually set the camera’s protocols such as its ID

address, baud rate and RS485 protocol.

Automatic turnover:

When the camera reaches its maximum tilt position, by continuing the movement on a

PTZ controller, the lens will automatically flip 90° and rotate 180° horizontally. Therefore

the user will not have to scroll all the way back to the opposite viewing angle, allowing

them to a achieve 180 ° continuous surveillance.

Reserve and Call Preset:

Users can store up to 256 Presets which can be set via the speed dome itself or via a

compatible controller

Lens/Iris Control:

The camera’s lens can be fully controlled via a PTZ controller such as the zoom and focus.

Additionally if you want to reset lens (i.e. auto-focus) the user can simply shake the PTZ

controller’s joystick (left to right) or set up a relevant Preset.

Night vision:

The Speed Dome will automatically switch to its nightvision mode once the illumination

levels drop to a user specified level (Optional infrared lighting is required for the camera

to view in nightvision mode)

Patterns:

The camera can store up to 4 patterns which can then be launched by the PTZ

controller as predefined presets (i.e. numbers 84, 85, 86, and 87)

Tours:

The camera can store 1 Tour, which allows the camera to move to a user-defined pattern,

which itself is a sequence of user-defined Preset points. The tour can then be easily

launched by the PTZ controller.

1.3 PACKAGE CONTENTS

The packaged box for the XSD27ZIR-2 comes with the following items:

XSD27ZIR-2 Speed Dome Camera

Wall Bracket

Power Supply

Screws

Allen key

User Manual

Should any of these items be missing please contact your local distributor.

XSD27ZIR-2 - User Manual

2. INSTALLATION INSTRUCTIONS

2.1 Warning

This symbol on the product or on its packaging indicates that this product should not be

treated as household waste. Instead, you should make arrangements for the recycling of this

unit.

By ensuring this product is disposed of correctly, you will help to prevent harm to the

environment, and avoid possible health issues, which may be caused by inappropriate waste

handling of this product.

The recycling of materials helps to conserve our natural resources. For more detailed

information about recycling of this product, please contact your local council office, your

household waste disposal service or the shop where you purchased the product. In addition

you can find further information online at www.environment-agency.co.uk

WARNING: This symbol is intended to alert the user to the presence of

non-insulated “dangerous voltage”.

CAUTION: This symbol is intended to alert the user to presence of

important operating and maintenance (Servicing) instructions in the

literature accompanying the appliance.

Disposal of Old Electrical & Electronic Equipment (Applicable in the

European Union and other European countries with separate collection

systems- WEEE).

XSD27ZIR-2 - User Manual

Prior to installation and use of this product, please observe the following points:

Installation and servicing should be carried out by qualified service personnel.

It is important that the dome camera is not left in a position where the camera is pointing

directly at the sun or other extremely bright light source. This may result in CCD damage

and poor image quality.

The installation position must be as far away from high voltage sources as possible.

The dome cover is high quality optical product - Try to avoid touching it as any scratches

or marks left on the surface could affect image quality (we recommend the use of cotton

gloves when handling). Please refer to the installation manual for further guidance

In order to get the optimum image at all times, the dome cover should be cleaned

periodically. Be careful when cleaning; only hold the cover edge, avoiding direct contact

with the dome cover. Acid from fingerprints will damage the coated surface of the dome

cover. Direct contact with hard objects could lead to deterioration of the image. Please

use a soft clean cloth or similar to clean interior and exterior surfaces of the cover. A

neutral detergent (non-acid based) or high-grade furniture detergent may be used.

Only use replacement parts recommended by your local distributor.

After replacement/repair of this unit’s electrical components, take a resistance

measurement between line and exposed parts to verify the exposed parts have not been

connected to line circuitry.

When unpacking the dome, the Pan/Tilt module should be handled with care. Do not

place in a position where something could rub against or fall onto the housing.

When installing camera module, avoid touching any parts which could be easily damaged,

such as the optics and PCB.

Make sure all power and telemetry connections are complete before powering up the

camera.

Do NOT install the camera close to the air outlet of an air conditioning unit as the camera

may be affected by the resulting water condensation.

XSD27ZIR-2 - User Manual

2.1 Wiring

Connections:

RS485 Connection: Ensure that the camera and PTZ controller/keyboard/DVR are

connected by a suitable CAT-5 cable. If you have more than 1 dome please set

incremental addresses for each camera. Please ensure that the camera’s setting (i.e. Baud

Rate, Camera ID etc.) match/correspond between the Speed Dome and controlling

device.

Video Connection: Use a BNC cable to connect the speed dome directly to a monitor or

DVR.

Power Supply Connection: Ensure that the camera to a suitable power outlet, ensuring

that you use the power supply provided.

3. BASIC OPERATIONS

Please Note:

When you turn on the power for speed dome it will begin to initialise for a few

seconds, as the camera runs a self-test protocol

Handle with care whilst installing the camera ensuring that none of the moving

parts are damaged.

Use shielded cable and do not mix with other cables.

Keep the PTZ dome camera or signal transmission cable away from high voltage

equipment or cables (at least 50 meters) and ensure that is lightning and surge

protection

Do not use the PTZ dome camera in environments of extreme temperature or

humidity. The temperature should be between -25 ° and 50° with humidity <90%

XSD27ZIR-2 - User Manual

3. OPERATING BASICS

To control the PTZ functions you will need use a compatible PTZ joystick/keyboard

controller/DVR. These instructions are based upon Xvision’s XSDZ-3DM Speed Dome Joystick

controller.

Setting up Presets:

A Preset is a fixed position of the camera and its lens, which is defined by the user. A

Preset includes both the lens’ position (i.e. horizontal/vertical position) and its state

(i.e. zoom magnification and Iris)

Use the PTZ controller to set the camera chosen position, zoom and iris

Using the controller press the SET button, then key in the chosen Preset number (i.e.

number 9) and press the PRESET (PRE) button to store the chosen parameters.

To Call a Preset:

Key in the chosen Preset number and press the PRE button to move the camera to

the chosen preset parameters (i.e. position, zoom and Iris)

A list special defined Presets recognised by the Speed Dome are listed below as follows:

SPECIAL PRESETS

FUNCTION

95 + CALL

Enter Main Menu

XXX + PRESET (PRE)

Reserve Preset xxx

XXX + CALL

Call Preset xxx

82 + CALL

Frame Scan (Left to Right image scan)

83 + CALL

Delete all presets

84 + CALL

Call Pattern 1

85 + CALL

Call Pattern 2

86 + CALL

Call Pattern 3

87 + CALL

Call Pattern 4

88 + CALL

Preset 1-10 cruise

89 + CALL

Preset 11-20 cruise

90 + CALL

Preset 21-30 cruise

91 + CALL

Preset 31-40 cruise

96 + CALL

360° Scan

98 + CALL

360° continuous scanning

99 + CALL

Preset Cruise (Tour)

Please Note: PTZ joystick/Controller manufacturers may have different operational

configurations. Please refer to the manufacturer’s operating manual for further details.

XSD27ZIR-2 - User Manual

4. MENU SETTINGS

4.1 Main Menu

The items in the main menu are listed below as follows:

SYSTEM INFORMATION: Displays the camera’s general information

ADDR SETTING: Camera’s operating protocols

MOTION: PTZ Movement Settings

PATTERNS: Configure Patterns

CAMERA: Configure settings for the lens

CRUISE SETTING: Configure Cruises

DISPLAY SETUP: Configure displayed on-screen information.

RESTORE FACTORY DEFAULT: Restores the factory default setting

REBOOT SYSTEM: Reboot the camera

EXIT: Exit the OSD menu

4.2 SYSTEM INFORMATION

The System Information option displays the speed domes general operating parameters and

information which is displayed as follows:

The System Information menu items are explained as follows:

COM: Baud Rate, Parity Bit, Date Bit and Stop Bit

ADDRESS: Camera ID for PTZ control (i.e. between 0-255)

SOFTWARE VERSION: Current software version

BACK: Returns back to the previous menu

EXIT: Exits the main menu

4.3 ADDRESS SETTING

The address setting menu is displayed as follows:

SYSTEM INFORMATION

COM 9600, N, 8 ,1

ADDRESS 1

SOFTWARE VERSION V5.2

BACK

EXIT

ADDR SETTING

ADDR TYPE HARD

ADDR SOFT 255

ADDR HARD 1

BACK

EXIT

Please Note: The options described with the System Information cannot be changed

within this menu

XSD27ZIR-2 - User Manual

The speed domes address type (ADDR TYPR) can set between either SOFT (automatically

obtains an address) or HARD (address is physically set via the dip-switches). Once selected

press the <OPEN> button to save any changes. Similarly uses the joystick to scroll through the

other options to set either the ADDR SOFT or ADDR HARD.

Once completed you can select BACK or EXIT options to leave the setup.

4.4 MOTION (PAN/TILT SETTINGS)

The Motion option menu is displayed as follows:

< FRAME SCAN>: Allows the user to setup the camera’s maximum left/right position

during a scan and displays the following menu:

To setup the left/right maximum positions select SET SCAN POSITION and the following

menu will be displayed

To set the LEFT LIMIT POSITION move the joystick to the desired location and press the

<OPEN> button on your controller to save. Once saved the user will be prompted to set

RIGHT LIMIT POSITION as shown below:

MOTION

< FRAME SCAN>

POWER UP NONE

PARK TIME 15s

PARK ACTION NONE

BACK

EXIT

FRAME SCAN

SET SCAN POSITION

CLEAR FRAME SCAN

FRAME SCAN SPEED 16

BACK

EXIT

SET FRAME SCAN

LEFT LIMIT POSITION

IRIS OPEN TO CONTINUE

SET FRAME SCAN

RIGHT LIMIT POSITION

IRIS OPEN TO CONTINUE

Andere Handbücher für XSD27ZIR-2

Inhaltsverzeichnis

Andere X-Vision Sicherheitskamera Handbücher

X-Vision

X-Vision XP1080B Bedienungsanleitung

X-Vision

X-Vision XSD27ZDN Bedienungsanleitung

X-Vision

X-Vision PCC435 Bedienungsanleitung

X-Vision

X-Vision XC960T Bedienungsanleitung

X-Vision

X-Vision X100 Series Bedienungsanleitung

X-Vision

X-Vision CVR811 Bedienungsanleitung

X-Vision

X-Vision XC960DA Bedienungsanleitung

X-Vision

X-Vision VIS238D Bedienungsanleitung

X-Vision

X-Vision XIR621 Bedienungsanleitung

X-Vision

X-Vision XPD621 Bedienungsanleitung

X-Vision

X-Vision VIS449E Bedienungsanleitung

X-Vision

X-Vision VIS249D Bedienungsanleitung

X-Vision

X-Vision VIS249D-2 Bedienungsanleitung

X-Vision

X-Vision VIS338D Bedienungsanleitung

X-Vision

X-Vision PCC427 Bedienungsanleitung

X-Vision

X-Vision XC960S30IRN Bedienungsanleitung

X-Vision

X-Vision XPD721WIR Bedienungsanleitung

X-Vision

X-Vision VIS338DX-3 Bedienungsanleitung

X-Vision

X-Vision XSD27ZIR Bedienungsanleitung

X-Vision

X-Vision XSD27ZIR-2 Bedienungsanleitung

X-Vision

X-Vision XIR501 Bedienungsanleitung

X-Vision

X-Vision XC960BN Bedienungsanleitung

X-Vision

X-Vision VIS430R Leitfaden

X-Vision

X-Vision XC960VV Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung