XtendLan IP SENSOR ESZ-162 Bedienungsanleitung

ESZ-162

USER MANUAL

Warning:Anychangestothisequipmentwithoutpermissionmaycausedamagestoyourequipment!This

equipment has been authenticated byFCC and CE, it can be preventedfrom theinfluenceof harmful

electronicjammingin normal business use condition.

IMPORTANT NOTICE

1. IP SENSOR ESZ-162 is only designed for splash-proof shell. Wehave no responsibilityfor the

possible damagecausedbybadlyworkingenvironment

2. PleaseusetheDC adapterprovidedbythedealer,we haveno responsibilityforthepossibledamage

causedbyusing other adapter

3. Do not use IP SENSOR ESZ-162 in strongshaking condition.

4. Please contact the dealer if IP SENSOR ESZ-162 worksimproperly.

a retrieval system, or transmitted in anyform or by any means, electronic, mechanical, photocopying,

recording or otherwise, without the prior written consent of XtendLan

All other products mentioned in this document are trademarks of their respective manufactures.

-3-

Table of Content

1. INTRODUCTION................................................................................................................4

FEATURES .........................................................................................................................

ESZ-162 FUNCTION DESCRIBE

................................................................................................

2.SPECIFICATION...............................................................................................................6

PACKAGECONTENTS.........................................................................................................

MINIMUMSYSTEMREQUIREMENTS ....................................................................................

3.INTERFACE DESCRIPTION ..........................................................................................7

4.HARDWARE & SOFTWARE INSTALLATION............................................................8

HARDWAREINSTALLATION..................................................................................................

SOFTWAREINSTALLATION..................................................................................................

5. INITIAL SETTING...............................................................................................................9

INITIALSETTINGTHROUGHETHERNET ................................................................................

READMESSAGEFROMRS232 SERIAL-PORT.......................................................................

6. CONTROL AND SETTING THROUTHTHE INTERNET EXPLORE...................... 10

STATEREPORT..................................................................................................................

SETTINGTHEIP ADDRESS…………………… ………………………………………………

SETTINGTHEDDNS..........................................................................................................

SETTINGTHEE-MAIL.......................................................................................................…

SETTING THE PASSWORD………………………………………………… …………… …..

NETWORK AKE UP FUNCTION.………………………… ……………………………………

SNMPSETTINGS……………………………………… ……………………………….. ….

MONITORINGSETTING……………………… …………… ………… ……… …… ……..

EXTERNALVOLTAGELEVELMONITORING…………… ……………… ……… …… ……..

ONLINEFIRMWAREUPDATE………………………………… …………………………. …

7. CONTROL AND SETTING THROUTH HTTP COMMAND..................................... 20

-4-

1. introduction

IP SENSOR ESZ-162 is a web sensor with build-in web server which can be easy used in the industry

supervise filed. With the remote net control technology, user can get the IO state of remote equipments,

monitoring the voltage, temperature or working state of power supply directly in remote. User can start the

fan and when the fan is not working properlyit willmakean alarm automatically.

Usercando thisin anycomputer connectedto the internet or localarea network, no needforanyspecial

program or computer.This designis easyto use, is fit for the office/industryautomation or housesecurity

manage.Otherwisethe populardeveloptoolVB/VCis providedforusertomodifytheapplicationsaccordingto

your own needs.

Feature

1. Builtin web server, can be used through the Ethernet network or Internet network withoutcomputer.

2. Supported 10/100M Ethernet and TCP/IP UDP,ICMP, DHCP, HTTP protocol.

3. Builtin network browser interface, you can remote receive or triggerthesignalof drycontactoperatethe

switch and check thestate. Support multi platform and server application,such as InternetExplore,

Netscape,Mozilla(Linux).

4. 16 route input digitalsignals monitoring, 8 input signals can be setto drycontactor wet contact.

5. 3 routeDC voltagemonitoring, ESZ-162 will alarm if voltage is outof presetnormal range.

6. Controlthestartupandturnoff of 3routefan,monitoringtheoperationof eachfan,ESZ-162willalarm if rotate

speedis lower than the presetlower limit.

7. 2 route temperature monitoring, ESZ-162 will alarm if temperatureis higher than the preset normal range.

8. Supported HTTP, SMTP,SNMP,INTERNET-fixedIP,DDNS, DHCP,LAN–virtualIP

9. Security passwords identify. Easilyinstalled andcanbe updated online.

10.Supported serial portcommunication, indicate all kinds of real time stateof ESZ-

162. 11.Supportedhttp command.

12.Built in Watch Dog.

13.LEDdisplay indicates the status.

14.Develop tool SDK (VB/ VC) is provided.It can be modified to meet theuser’s specialneed.

15.Safely designed for high voltage resistance and protection for leakage of electrical currency, using

nonflammablematerial

16.Polarityprotective—no damage to yourequipmentif you reverse the polarity in installation.

17.It canbe usedseparatedor associated with other series products of XtendLan.

-5-

ESZ-162function describetions

1. Voltagemonitoringof ESZ-162

ESZ-162canmonitor3standardvoltageof 12V,5V,3V.Whenthese3 under monitoringvoltagearebeyondof

the predetermined upper limit or lower limit,the buzzer will make an alarm as enable .

2. Temperaturemonitoringof ESZ-162

ESZ-162can monitor 2 route temperaturesignals.The monitoring temperature can be predeterminedbyuser.

T1 is the temperaturesensorfor ESZ-162 circuitboard,canindicatethe owntemperature of ESZ-162.T2 and

T3is outlet temperature sensors,the temperature will displayto -48 degree if the sensor has not been

connected.When anyof the 3 sensor’s temperatureis beyondof thepredeterminedupperlimit,the buzzer

willmakean alarm (if thisalarm functionis notforbiddenbyuser).Onlywhenthetemperatureis lower than

theupperlimitagain,the alarm will stop.

3. Fanmonitoringof ESZ-162

ESZ-162canmonitoring3 route fan ( DC fan,12V/0.5A),if the workingfan’s rotate speed is lower than the

preset value, the buzzer will make an alarm(if this alarm functionis not forbidden byuser)

4. 16 route inputsignals monitoring

ESZ-162canmonitor 16 route inputsignals; user canget the voltage lever of eachroute signal. There are 8 dry

contacts(DI01–DI08),DI09–DI16canbesetto drycontactor wetcontact.Whenaportis settodrycontact,

ESZ-162 willsupplyDC 5V to contact,monitoring if there is an externalswitch on or switchoffmovement.

5. Monitoringthrough RS232 serial-port

User can monitor the working state in each portof ESZ-162 throughthe RS232serial-port.

6. E-mailreport

When ESZ-162starts up or the presetalarm event happens, ESZ-162 can automaticallysend e-mail

reportto the mailbox preset by user.

7. Settingthe passwordand IP

Usercansetthe password and IP addressof ESZ-162, supporting control multiple ESZ-162s in one local

network.

-6-

8. Settingthe buzzer

User can turn off the buzzer in setup webpage, then buzzer will not alarm . User can turn off the alarm in one

monitoring item, so when this monitoring item reach the alarm level , ESZ-162 will not alarm. When one or

multiple monitoring item trigger the alarm, you can cancel the alarm by pressing the alarm reset button, but

whenthese

monitoring item reach the alarm level again, the buzzer will make an alarm again.

9. LED display

ESZ-162candisplay its workingstate through thedigital LED, for example:

Displayfrom left to right :

IP , 192 , 168 , 100 , 99 , 80 , P1 , 3.00, P2, 0.03, P3 , 2.00 , T1, 29 , T2 , -48 , T3, -48, F1, 3824,

F2, 3633, F3, 0 .

* IP : means following willdisplay the IP address of ESZ-162. IF following displays 192, 168, 10, 100 : 50

(in 5 times),it meansthe IP addressof ESZ-162is 192.168.10.100: 50.

* V1 V2 V3 : means following willdisplaythe voltage valuesof 3 routemonitoringvoltage.

* T1T2 T3: means following will displaythe temperature valuesof 3 route monitoringtemperature(in degree

centigrade, C)

* F1 F2 F3: meansfollowing will displaythe rotatespeed of 3 routemonitoringfan.

2.Specification

ESZ-162E package contents

One setof ESZ-162

One1A,110~220V power adapter

2 temperaturesensors

3 voltage sensor wires

Minimum System Requirements

■

Intel Pentium III 300MHzor above/compatible AMD CPU

■

WINDOWS operating system (IE5.0+SPI) & LINUX

■

Minimum 64MBRAM

■

VGA Card:supported direct draw

Network card with RJ45 port & Ethernet HUB or Switcher

■

Internet network (Ethernet, ADSL or other ways, depends on whether you need far end control ability or

not)

-7-

3. Interface Description

Interfaceof ESZ-162 is as thefigureshows:

Description of each port:

1. RJ45Ethernet port 2. RS232 serialport

3. LED board 4. DC 12V input

5 Portof Fan3 6. Portof Fan2

7. Portof Fan1

9. Portof temperaturesensor2 8. Portof temperaturesensor 3

10. Portof voltage sensor 3

11. Portof voltagesensor 2 12. Portof voltagesensor1

13. DI1 ~ 4 port 14. DI 5 ~ 8 port

15. DI 9 ~D 12 port 16. DI 13 ~ 16 port

17. DI for 12V : Internal debug purpose.

18& 19 : . SW 1 & SW2 - Setting the type of DI9-DI16contact to dryor wetcontact.When SW2 is on, the

respondingcontactis wet contact;when SW2 is off,the respondingcontactis drycontact.

SW1 is responding to DI9, SW2 is responding to DI16 (each contact needs the setting

of SW1 and SW2 at the same time)

For Example :

A. Set DI 9 & 13 as drycontact ：1 –ON , 5 –ON , 1- ON , 5 –ON .

B. Set DI 10 & 14 as wet contact ：2 –OFF , 6 –OFF, 2- OFF , 5 –OFF .

20. Alarm reset button: when alarming, press this button to turn off the alarm of buzzer.

(Keeppressing for10secondswillsettheIPaddressandpasswordof ESZ-162 backtofactorydefault)

21. Internal debug purpose.

-8-

4. Hardware & Software installation

Before you star to useIP SENSORESZ-162,pleasefollowthe steps below

■

Check the package to make sure the contents is complete.

■

prepareone Ethernet HUBor Router

■

Check the voltage of thepower supplyto makesureit is AC 110-240 volt

Hardwareinstallation

1 Connectthe ESZ-162to HUB throughnetwork wire.

2 Connectthe HUB or Routerto theinternet (MaythroughADSL/XDSLmodem).

3 Connectthe power adapter to the ESZ-162.

4 Connect the power adapters of under controlelectricequipmentto corresponding

outport of ESZ-162.

* ESZ-162 HUB XDSL or * ESZ-162 HUB / ROUTER XDSL

Turnon your computer and the power adapter of IP SENSOR ESZ-162.

Software installation

HavingconnectedthepowersupplyandnetworkwirewithRJ45porttotheESZ-162,pleaseinstallthe

softwareas thefollowsteps:

1. Start yourcomputer,puttheinstalldiscin theCDROM,andthenfindthefilenamedipedit.exe inthe

installdisc.

2. Copythefileto desktopor any directory you want save to.

Start the initial setting process following the construction in nextsection.

-9-

5. Initial Settings

Initial setting through the Ethernet

1. Double click the Edit.exe :

2. All the IPs in thesame subnet of the Ethernet

willbe found and be displayin the window bythe

software.

The default name of IP SENSORESZ-162 is IP

TERMINAL.

The default IP address of ESZ-162 is fixed at

192.168.100.100.

3. Click the equipment‘s name that you want to edit in the left of the window; it will turnfuscous,the

equipment’s nameandIPaddresswilldisplayinthewindows,youcanrename(usenumbersand letters).After

that,click the update button and the new setting will be work in 20 seconds.

4. Doubleclickthenameoftheequipmentyouwanttocontrol,theIE browserwindowwillopenandconnected

tothisequipmentin thatEthernetautomatically. Youalsocantype theIPaddressof the ESZ-162intheIE

browser to open the web pageof ESZ-162.Wesuggestyouto updatethe IE to version6.0withSP1 or

higher if yourIE notices you thesecuritylevel is too low to openthat webpage.

NOTICE:

1. IP Sensor ESZ-162 defaultsettingisfixedIP address:192.168.100.100.TheIP addressof your

computer shouldin thesamesubnetwiththatof IP SensorESZ-162,so thatyoucanopenthe

controlwebpage.In

the figureabove,theIP addressof ESZ-162 is 192.168.100.168. You can make sure theIP address of

your computer first, thenuse the ipedit.exe to modifytheIPaddressof ESZ-162.after that,

your computer can connect to theESZ-162.

2. IF user can not enter the control web page, please set theIP address of IP Sensor ESZ-162 and

your computer in the same subnet. User canobtain thecomputer’s IP address,subnetmask,and

default gateway through the following method.

start run typein “cmd” then open the MS –DOS window, now typein “ipconfig”

-10-

The last number of the IP address(default is 100) canbe any number between1~254, but cannotbe thesame

withthatof thecomputer’s. If youwantto useit at home,you can enter theweb page bytyping in the IP, theIE,

or using ipedit.exeprogram.

*Same subnet : means the firstthreepartsof the IP addressmustbe the same, such as XXX.XXX.X.abc. For

example,192.168.1.100 and 192.168.1.123 are in the samesubnet.

4. The default username and password of IP Sensor ESZ-162

are: Username: admin

Password: 12345678

If forget password and can not log in webpage, please press Reset for 10 second , after few second

then restart power . Then the IP address and password will be back to default value

Read message from RS232 serial port

Usercanreadthe system state of ESZ-162 in PC through theRS232serial port in ESZ-162.

First,connectthe ESZ-162 serial portto PC serial port and make sure theconnection is correct.

Then,click the start menuin your PC,program---accessories---communicate---super terminal,setting as

the figurebelow shows:

* Bits per second ;19200

* Data bits : 8

* Parity:None

* Stopbits: 1

* Flowcontrol : NONE

Then you can read message of ESZ-162from RS232serialport.

Inhaltsverzeichnis

Andere XtendLan Zubehör Handbücher

XtendLan

XtendLan DPA-D2-QSW Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung