Xtreme X-500 Bedienungsanleitung

Page

X-500 Electric Scooter

Owner’s Manual

Revised 10/10/09

PLEASE BE SAFE WHEN RIDING

ALWAYS WEAR A HELMET AND OBEY ALL LAWS!

X-Treme TM Electric Scooters

Page

BATTERY MAINTENANCE and

CHARGING INSTRUCTIONS

1. You MUST charge completely prior to initial use. (Follow

charging instructions in your Product Handbook)

2. Charge immediately after each use.

3. Charge before storage. You must charge every 30 days if not

in use.

4. Charge the unit for 6-8 hours after the light on the charger turns

green.

5. DO NOT allow this unit to deep discharge the battery.

6. For safety purposes, DO NOT charge for over 24 hours.

7. Turn the unit OFF when not in use.

This PRODUCT IS NOT INTENDED FOR EXTREME or

OFF-ROAD Use! Please take care of your X-500!

DO NOT JUMP or ABUSE THIS PRODUCT!

DO NOT RIDE IN WET/ICY CONDITIONS!

Failure to follow these instructions will

VOID YOUR WARRANTY!

IMPORTANT

Failure to follow these INSTRUCTIONS will

VOID YOUR WARRANTY!

Page

WARNING

This product does not conform to Federal Motor Vehicle Standards and is not

intended for operation on public streets, roads or highways. Serious injury can

result from the unsafe operations of this product. Operator can minimize these

risks by using certain safety equipment such as: safety helmet, goggles, gloves,

elbow and kneepads and appropriate footwear.

DO NOT operate this product in traffic, on wet, frozen, oily or unpaved surfaces or

under the influence of drugs and/or alcohol. Avoid uneven surfaces, potholes,

surface cracks and obstacles.

DO NOT use a water hose to clean this product. See Product Handbook for more

information.

This product is recommended for riders 16 YEARS OF AGE and older.

SAFETY

Persons without excellent vision, balance, coordination, reflex, muscle and

bone strength and good decision-making capabilities should not use this

product.

Minors without adult supervision should not use this product.

Persons unwilling or unable to take responsibility for their own actions should

not use this product.

The user of this product assumes ALL risks associated with its use. To

minimize these RISKS, the user must wear safety helmet, goggles, gloves,

elbow and kneepads and appropriate footwear.

This product is ELECTRIC! DO NOT ride this product in wet conditions,

puddles or rainy weather.

IMPORTANT

PLEASE READ THIS BEFORE USING THIS PRODUCT

READ THIS FIRST!

Page

SAFETY GUIDE

The recommended age for riding this scooter is 16 years old.

To avoid damage to the motor and footplate, do not overload the scooter.

Never ride with more than one person.

Inspect your scooter thoroughly before each use for loose or missing parts.

Avoid unintentional starts by turning the scooter off while not in use.

To avoid the risk of a short circuit in the electrical parts, do not use your

X-Treme Electric scooter in the rain and never spray or wash off your scooter

with water.

Do not place the battery near fire or heat.

To avoid damage to the battery, do not use the charger if it has been damaged

in any way.

Keep hands, face, feet and hair away from all moving parts.

Do not touch the motor or wheels while they are rotating.

Brakes are designed to control speed as well as stop the scooter. Practice

braking for proper slowing down and smooth stops.

Maintain your X-Treme X-500 as recommended in this Product Handbook.

Use only quality replacement parts as recommended by the manufacturer.

Inspect the entire scooter prior to each use. Replace any part that is cracked,

chipped or damaged before use.

*NEVER ALLOW CHILDREN TO OPERATE THE SCOOTER WITHOUT ADULT

SUPERVISION.

*NEVER ATTEMPT TO OPERATE THE SCOOTER WHILE UNDER THE

INFLUENCE OF ALCOHOL.

If a situation arises that is not covered in the manual,

proceed with caution and use good judgment.

Contact your dealer or X-Treme (www.x-tremescooters.com/support/)

if you need further assistance

QUICK

REFERENCE

SAFETY GUIDE

Page

TABLE OF CONTENTS

IMPORTANT INFORMATION…………………………………….………………..2

QUICK REFERENCE……………………………………………………………….4

TABLE OF CONTENTS……………………………….…………….………………5

GETTING TO KNOW YOUR X-TREME X-500…………………………………..6

PACKAGE CONTENTS…………………………………………………………….7

GETTING STARTED………………..……………………………..………………..7

ASSEMBLY……………………………………………………………………...7

FUSE INSTALLATION…….……………………………………………………8

SEAT & SEAT POST INSTALLATION………………………………………...8

CHARGING……………………………………………………………………...8

RIDING/BRAKING………………………………………………………………9

FOLDING AND STORAGE……….………………………..……………………….9

TIRES AND WHEELS……….…………………………………….………………10

MAINTENANCE…………………………………………………………………….11

RECOMMENDED TOOLS…………………………………….……………...11

ADJUSTING THE HEAD UNIT…………….…………………………………11

ADJUSTING THE CHAIN…..………..……………….………………………12

MAINTENANCE SCHEDULE……………………………………...……………..13

OTHER QUESTIONS….…………………………………………………………..13

GENERAL INFORMATION/TECH SUPPORT………………………………….14

Page

GETTING TO KNOW YOUR X-TREME X-500

(Photo’s may vary)

Page

PACKAGE CONTENTS

Your X-Treme X-500 comes with the following items in the box. Please locate

all of the following:

1. The X-Treme X-500 Scooter

2. 48V Battery Charger

3. Tool Kit

4. 20amp Fuse(s)

5. Product Handbook

6. Seat & Seat Post

GETTING STARTED

Please read and understand these instructions and the OPERATING

PROCEDURES section, prior to starting or riding your X-500

Assembly

1. Carefully remove the X-500 from the box.

2. To unfold the X-500, begin by pressing

down on the FOLDING HANDLE with one

hand (Fig.1), while gently pulling up on the

handlebars with the other (Fig.2)

3. Fully extend the handlebars to their upright

position until you feel the mechanism lock

into place (Fig. 3).

4. Attach the handlebars by first attaching the

large handlebar clamp to the top of the

handlebar down tube. Then attach the

handlebars to the clamp. Tighten all bolts

after adjusting the handlebars to the

desired tilted position. (Fig. 4)

5. The BRAKE LEVER is in the down position

for shipping. Using the provided Allen

Wrench, loosen the tension bolt, and adjust

the levers to a comfortable position.

*BE CAREFUL NOT TO PULL ON THE

CABLES!

Page

Fuse Installation

Your scooter comes with a 20amp fuse that is NOT installed at the factory.

Follow the instructions below to properly install the fuse before attempting to use your

scooter.

1. Locate the 20amp glass fuse that came with your scooter.

2. Locate the fuse holder on the right side of the scooter frame under the footplate.

(Fig.5)

3. Remove the fuse holder cap and insert the fuse into the cap first.

4. Then insert fuse/cap into fuse holder and gently tighten. DO NOT OVER

TIGHTEN THE CAP.

Seat and Seat Post Installation

1. Insert the seat post into the bottom of the seat and tighten securely.

2. Next, insert the seat post into the post receiver that is already attached to the

footplate on the scooter and tighten the clamp securely.

Charging

Your scooter comes charged out of the carton. We still recommend charging the unit for

6-8 hours prior to it’s first use. We also recommendcharging your scooter after each use

and prior to storage.

WARNING: Do not allow your scooter to go into deep discharge, as this will damage the

batteries.

Fig. 5

Fig. 6

1. Make sure unit is turned off.

2. Open the charging socket cover

located on the right side of the

scooter frame, under the footplate.

(Fig. 5)

3. Locate your Battery Charger. (Fig.

6) Find the charger socket end

that has a three-prong socket and

plug it into the scooter.

4. Next, plug the AC plug into a wall

outlet.

When first plugged in, the charger has two

red lights that will illuminate at the same

time, indicating that the charging process

has started. Once the light on the charger

turns green, you may remove the charger

and close the safety cap.

Page

Riding

1. Make sure that all of the exposed bolts and screws are tightened.

2. Raise the kickstand to its upright position.

3. Push the on/off switch (located on the left handlebar) to the ON position.

4. Put one foot on the deck of the X-500 while pushing off with the other foot, gently

rotate the THROTTLE GRIP, on the right side of the handlebars. The X-500 will begin

to move on its own power.

**Your scooter has a variable speed hand throttle. You can control the speed of your

scooter by the amount of pressure you use when rotating the hand throttle. The more

you rotate, the faster you will go.

Stopping/Braking

1. To brake, release the THROTTLE GRIP and depress the BRAKE LEVERS (on the

left/right side of the handlebars. Depressing the brake will disengage power to the

motor. When the unit feels like it is loosing power or not accelerating to full speed,

the scooter is ready to be re-charged.

NOTE: If the on/off switch is left in the ON position for more than 10-15 minutes without

moving, Smart Power will shut itself OFF. To reset, turn the unit OFF, wait a few seconds

and then switch it back ON again.

FOLDING & STORAGE

When you are done riding the X-500 you can fold it down for compact storage and

transportation. To fold down the X-500, use one hand to push down on the folding handle

while gently pushing down on the handlebars. BE CAREFUL NOT TO HIT YOUR HEAD

WITH THE HANDLEBAR. Push down until you feel the mechanism lock into the down

position.

BRAKING SYSTEM

The X-500 uses a pinch braking system for the front, and a disc/caliper system

for the rear They are both activated by a hand brake lever on the left and right

side of the handlebar. Squeezing the hand brake lever with your left hand

activates the rear brake. Squeezing the hand brake lever with your right hand

activates the front brake. Make sure to release the HAND THROTTLE GRIP

when engaging the brakes.

Practice braking on a smooth, dry surface to get used to the feel of the braking

system. Braking distance is affected by wet conditions and loose and uneven

riding surfaces.

Adjusting the Brakes

The Brakes on the X-500 should come fully adjusted from the factory.

Page

However, it may be necessary to adjust the brakes from time to time.

Fig. 12

Fig. 13

Squeaky Brakes

The brakes may squeak before they are broken in. This is normal and will not

affect the function or performance of the brakes. With continued use the

squeak should go away.

TIRE AND WHEELS

The X-Treme X-500 uses an identical rim and tires assembly on the front and

rear wheels, which means that the tires can be rotated. The wheels are

actually two wheel halves (split rim) bolted together to make it easier to remove

and replace the tire and tube.

The rear wheel is fitted with a special spacer to accommodate the chain

sprocket, while the front wheel has a bracket for the disc brake.

To adjust the rear brakes:

1. With one hand, depress the brake

caliper using your thumb and

forefinger (Fig.12).

2. With the other hand, adjust the

tension screw on the brake line.

a. Turn the tension screw

clockwise to loosen the brake.

b. Turn the tension screw

counterclockwise to tighten

brake.

To adjust the front brakes:

For brakes that are adjusted too tight:

1. Loosen the tension screw on the

right hand brake lever by rotating it

counter-clockwise until the wheel

spins freely.

For brakes that are adjusted too loose:

1. Tighten the tension screw on the

right hand brake lever by rotating it

clockwise until the wheel has a

slight drag.

For further adjustment:

1. Locate the adjustment screw on the

front brake assembly (located

above the front wheel, Fig. 13)

Tighten or loosen as necessary.

Inhaltsverzeichnis

Andere Xtreme Roller Handbücher

Xtreme

Xtreme X-560 Bedienungsanleitung

Xtreme

Xtreme XB-500 Bedienungsanleitung

Xtreme

Xtreme XG-505 Bedienungsanleitung

Xtreme

Xtreme XG-470 Bedienungsanleitung

Xtreme

Xtreme XMB-400 Bedienungsanleitung

Xtreme

Xtreme XB-420M Bedienungsanleitung

Xtreme

Xtreme XG-499 Bedienungsanleitung

Xtreme

Xtreme XG-565 A-Blaze Signature Series Bedienungsanleitung

Xtreme

Xtreme X-140 Bedienungsanleitung

Xtreme

Xtreme X-370 Bedienungsanleitung

Xtreme

Xtreme XT300 Bedienungsanleitung

Xtreme

Xtreme XR-101 Bedienungsanleitung

Xtreme

Xtreme X-400 Bedienungsanleitung

Xtreme

Xtreme X-300 Bedienungsanleitung

Xtreme

Xtreme X-250 Bedienungsanleitung

Xtreme

Xtreme X-360 Bedienungsanleitung

Xtreme

Xtreme XR-301 Bedienungsanleitung

Xtreme

Xtreme XR-302 Bedienungsanleitung

Xtreme

Xtreme XG-550 Bedienungsanleitung

Xtreme

Xtreme XM-4000Li Fehlerbehebungshandbuch

Xtreme

Xtreme XM-5000Li Fehlerbehebungshandbuch

Xtreme

Xtreme XA-750 Bedienungsanleitung

Xtreme

Xtreme XB-300SLA Bedienungsanleitung

Xtreme

Xtreme XM-3000 Fehlerbehebungshandbuch

Beliebte Roller Handbücher anderer Marken

TEKTRO

TEKTRO CHEETAH Bedienungsanleitung

Douglas

Douglas Vespa Sprint Installationsanleitung

PLAYTIVE

PLAYTIVE AS-2448 Bedienungsanleitung

Ebinger

Ebinger DONKEY XL Bedienungsanleitung

Flyer

Flyer Mountain Benutzerhandbuch

BackCountry eBikes

BackCountry eBikes Storm Bedienungsanleitung

equipmed

equipmed FreeRoam II Bedienungsanleitung

Yoto

Yoto Lion Bedienungsanleitung

WESTHILL BIKES

WESTHILL BIKES LINK Bedienungsanleitung

BAnff

BAnff eProdigy series Bedienungsanleitung

Winther

Winther 475 Bedienungsanleitung

Jetson

Jetson JBZL17 Bedienungsanleitung

First Choice Mobility

First Choice Mobility Roma Medical Corella S741 Bedienungsanleitung

Carrera

Carrera impel Bedienungsanleitung

Afikim

Afikim Superlight SL-3 Bedienungsanleitung

CareCo

CareCo ZOOM Bedienungsanleitung

Douglas

Douglas Vespa G.S. Bedienungsanleitung

Gazelle

Gazelle with BOSCH System Bedienungsanleitung